- 01 Feb, 2020 1 commit
-
-
Gus Grubba authored
-
- 18 Jul, 2019 2 commits
-
-
Gus Grubba authored
-
Gus Grubba authored
Support up to 64 buttons, not limit to 16 Send a single button command and not a stream of commands at 25Hz Send button commands through signals (it's coming from a different thread) Hide gimbal support through analog channels (there are no MAVLink messages to handle it)
-
- 17 Jul, 2019 1 commit
-
-
Gus Grubba authored
Add gimbal to external control signal
-
- 16 Jul, 2019 1 commit
-
-
Gus Grubba authored
-
- 15 Jul, 2019 1 commit
-
-
Gus Grubba authored
Add camera trigger Add video start/stop/toggle recording Add gimbal pitch and yaw
-
- 06 Feb, 2018 1 commit
-
-
nanthony21 authored
Joystick axes and buttons can now be monitored even when the joystick input is disabled.
-
- 05 Feb, 2018 4 commits
-
-
Nick Anthony authored
Minor improvement to detection of stick recentering after calibration. Without this if you performed a calibration with deadband enabled but one of the deadbands at the end of the calibration was ~0 it would be very difficult to position the stick so that Qgroundcontrol considered the axis to be centered.
-
nanthony21 authored
-
nanthony21 authored
recentered after calibration.
-
nanthony21 authored
-
- 23 Oct, 2017 1 commit
-
-
DonLakeFlyer authored
-
- 28 Feb, 2017 1 commit
-
-
Nick Anthony authored
This reverts commit 7131a12e.
-
- 26 Feb, 2017 2 commits
-
-
nanthony21 authored
-
nanthony21 authored
-
- 25 Feb, 2017 3 commits
-
-
nanthony21 authored
-
nanthony21 authored
-
nanthony21 authored
-
- 27 Jan, 2017 1 commit
-
-
Jacob Walser authored
-
- 25 Jan, 2017 2 commits
-
-
Jacob Walser authored
-
Jacob Walser authored
-
- 24 Jan, 2017 1 commit
-
-
Jacob Walser authored
-
- 15 Oct, 2016 1 commit
-
-
Gregory Dymarek authored
-
- 14 Oct, 2016 1 commit
-
-
Gregory Dymarek authored
-
- 11 Oct, 2016 1 commit
-
-
Gregory Dymarek authored
-
- 16 Jun, 2016 1 commit
-
-
Don Gagne authored
-
- 31 May, 2016 1 commit
-
-
Lorenz Meier authored
-
- 16 Jan, 2016 1 commit
-
-
Rustom Jehangir authored
The lines removed set the center point of the throttle axis to one extreme of the joystick range. This causes an offset value when the stick is centered if the joystick does not return exactly zero. This is important for vehicles with reversible throttle, such as ground robots or boats.
-
- 06 Dec, 2015 1 commit
-
-
Don Gagne authored
-
- 22 Nov, 2015 1 commit
-
-
Lorenz Meier authored
Joystick: Fix calibration and default use: Do not send anything to vehicle until enabled. Enable after calibration by default.
-
- 30 Oct, 2015 1 commit
-
-
Don Gagne authored
Instead us a Toolbox concept which hangs off of QGCApplication
-
- 21 Oct, 2015 1 commit
-
-
Don Gagne authored
-
- 10 Oct, 2015 1 commit
-
-
Don Gagne authored
-
- 09 Oct, 2015 1 commit
-
-
Don Gagne authored
-
- 25 Sep, 2015 1 commit
-
-
Don Gagne authored
-
- 23 Sep, 2015 1 commit
-
-
Lorenz Meier authored
-
- 05 Sep, 2015 1 commit
-
-
Daniel Agar authored
-
- 04 Sep, 2015 2 commits
- 03 Sep, 2015 1 commit
-
-
Don Gagne authored
-