ParameterFactMetaData.xml 186 KB
Newer Older
1
<?xml version='1.0' encoding='UTF-8'?>
2
<parameters>
3
  <version>3</version>
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57
  <group name="UAVCAN Motor Parameters" no_code_generation="true">
    <parameter default="75" name="ctl_bw" type="INT32">
      <short_desc>Speed controller bandwidth</short_desc>
      <long_desc>Speed controller bandwidth, in Hz. Higher values result in faster speed and current rise times, but may result in overshoot and higher current consumption. For fixed-wing aircraft, this value should be less than 50 Hz; for multirotors, values up to 100 Hz may provide improvements in responsiveness.</long_desc>
      <unit>Hertz</unit>
      <min>10</min>
      <max>250</max>
    </parameter>
    <parameter default="1" name="ctl_dir" type="INT32">
      <short_desc>Reverse direction</short_desc>
      <long_desc>Motor spin direction as detected during initial enumeration. Use 0 or 1 to reverse direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="1" name="ctl_gain" type="FLOAT">
      <short_desc>Speed (RPM) controller gain</short_desc>
      <long_desc>Speed (RPM) controller gain. Determines controller
            aggressiveness; units are amp-seconds per radian. Systems with
            higher rotational inertia (large props) will need gain increased;
            systems with low rotational inertia (small props) may need gain
            decreased. Higher values result in faster response, but may result
            in oscillation and excessive overshoot. Lower values result in a
            slower, smoother response.</long_desc>
      <unit>amp-seconds per radian</unit>
      <decimal>3</decimal>
      <min>0.00</min>
      <max>1.00</max>
    </parameter>
    <parameter default="3.5" name="ctl_hz_idle" type="FLOAT">
      <short_desc>Idle speed (e Hz)</short_desc>
      <long_desc>Idle speed (e Hz)</long_desc>
      <unit>Hertz</unit>
      <decimal>3</decimal>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="25" name="ctl_start_rate" type="INT32">
      <short_desc>Spin-up rate (e Hz/s)</short_desc>
      <long_desc>Spin-up rate (e Hz/s)</long_desc>
      <unit>Hz/s</unit>
      <min>5</min>
      <max>1000</max>
    </parameter>
    <parameter default="0" name="esc_index" type="INT32">
      <short_desc>Index of this ESC in throttle command messages.</short_desc>
      <long_desc>Index of this ESC in throttle command messages.</long_desc>
      <unit>Index</unit>
      <min>0</min>
      <max>15</max>
    </parameter>
    <parameter default="20034" name="id_ext_status" type="INT32">
      <short_desc>Extended status ID</short_desc>
      <long_desc>Extended status ID</long_desc>
      <min>1</min>
Don Gagne's avatar
Don Gagne committed
58
      <max>100000</max>
59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93
    </parameter>
    <parameter default="50000" name="int_ext_status" type="INT32">
      <short_desc>Extended status interval (µs)</short_desc>
      <long_desc>Extended status interval (µs)</long_desc>
      <unit>µs</unit>
      <min>0</min>
      <max>1000000</max>
    </parameter>
    <parameter default="50000" name="int_status" type="INT32">
      <short_desc>ESC status interval (µs)</short_desc>
      <long_desc>ESC status interval (µs)</long_desc>
      <unit>µs</unit>
      <max>1000000</max>
    </parameter>
    <parameter default="12" name="mot_i_max" type="FLOAT">
      <short_desc>Motor current limit in amps</short_desc>
      <long_desc>Motor current limit in amps. This determines the maximum
            current controller setpoint, as well as the maximum allowable
            current setpoint slew rate. This value should generally be set to
            the continuous current rating listed in the motor’s specification
            sheet, or set equal to the motor’s specified continuous power
            divided by the motor voltage limit.</long_desc>
      <unit>Amps</unit>
      <decimal>3</decimal>
      <min>1</min>
      <max>80</max>
    </parameter>
    <parameter default="2300" name="mot_kv" type="INT32">
      <short_desc>Motor Kv in RPM per volt</short_desc>
      <long_desc>Motor Kv in RPM per volt. This can be taken from the motor’s
            specification sheet; accuracy will help control performance but
            some deviation from the specified value is acceptable.</long_desc>
      <unit>RPM/v</unit>
      <decimal>0</decimal>
      <min>0</min>
Don Gagne's avatar
Don Gagne committed
94
      <max>4000</max>
95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118
    </parameter>
    <parameter default="0.0" name="mot_ls" type="FLOAT">
      <short_desc>READ ONLY: Motor inductance in henries.</short_desc>
      <long_desc>READ ONLY: Motor inductance in henries. This is measured on start-up.</long_desc>
      <unit>henries</unit>
      <decimal>3</decimal>
    </parameter>
    <parameter default="14" name="mot_num_poles" type="INT32">
      <short_desc>Number of motor poles.</short_desc>
      <long_desc>Number of motor poles. Used to convert mechanical speeds to
            electrical speeds. This number should be taken from the motor’s
            specification sheet.</long_desc>
      <unit>Poles</unit>
      <min>2</min>
      <max>40</max>
    </parameter>
    <parameter default="0.0" name="mot_rs" type="FLOAT">
      <short_desc>READ ONLY: Motor resistance in ohms</short_desc>
      <long_desc>READ ONLY: Motor resistance in ohms. This is measured on start-up. When
            tuning a new motor, check that this value is approximately equal
            to the value shown in the motor’s specification sheet.</long_desc>
      <unit>Ohms</unit>
      <decimal>3</decimal>
    </parameter>
Don Gagne's avatar
Don Gagne committed
119
    <parameter default="0.5" name="mot_v_accel" type="FLOAT">
120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138
      <short_desc>Acceleration limit (V)</short_desc>
      <long_desc>Acceleration limit (V)</long_desc>
      <unit>Volts</unit>
      <decimal>3</decimal>
      <min>0.01</min>
      <max>1.00</max>
    </parameter>
    <parameter default="14.8" name="mot_v_max" type="FLOAT">
      <short_desc>Motor voltage limit in volts</short_desc>
      <long_desc>Motor voltage limit in volts. The current controller’s
            commanded voltage will never exceed this value. Note that this may
            safely be above the nominal voltage of the motor; to determine the
            actual motor voltage limit, divide the motor’s rated power by the
            motor current limit.</long_desc>
      <unit>Volts</unit>
      <decimal>3</decimal>
      <min>0</min>
    </parameter>
  </group>
139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184
  <group name="Attitude EKF estimator">
    <parameter default="1e-4" name="EKF_ATT_V3_Q0" type="FLOAT">
      <short_desc>Body angular rate process noise</short_desc>
    </parameter>
    <parameter default="0.08" name="EKF_ATT_V3_Q1" type="FLOAT">
      <short_desc>Body angular acceleration process noise</short_desc>
    </parameter>
    <parameter default="0.009" name="EKF_ATT_V3_Q2" type="FLOAT">
      <short_desc>Acceleration process noise</short_desc>
    </parameter>
    <parameter default="0.005" name="EKF_ATT_V3_Q3" type="FLOAT">
      <short_desc>Magnet field vector process noise</short_desc>
    </parameter>
    <parameter default="0.0008" name="EKF_ATT_V4_R0" type="FLOAT">
      <short_desc>Gyro measurement noise</short_desc>
    </parameter>
    <parameter default="10000.0" name="EKF_ATT_V4_R1" type="FLOAT">
      <short_desc>Accel measurement noise</short_desc>
    </parameter>
    <parameter default="100.0" name="EKF_ATT_V4_R2" type="FLOAT">
      <short_desc>Mag measurement noise</short_desc>
    </parameter>
    <parameter default="0.0018" name="ATT_J11" type="FLOAT">
      <short_desc>Moment of inertia matrix diagonal entry (1, 1)</short_desc>
      <unit>kg*m^2</unit>
    </parameter>
    <parameter default="0.0018" name="ATT_J22" type="FLOAT">
      <short_desc>Moment of inertia matrix diagonal entry (2, 2)</short_desc>
      <unit>kg*m^2</unit>
    </parameter>
    <parameter default="0.0037" name="ATT_J33" type="FLOAT">
      <short_desc>Moment of inertia matrix diagonal entry (3, 3)</short_desc>
      <unit>kg*m^2</unit>
    </parameter>
    <parameter default="0" name="ATT_J_EN" type="INT32">
      <short_desc>Moment of inertia enabled in estimator</short_desc>
      <long_desc>If set to != 0 the moment of inertia will be used in the estimator</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
  </group>
  <group name="Attitude Q estimator">
    <parameter default="0.2" name="ATT_W_ACC" type="FLOAT">
      <short_desc>Complimentary filter accelerometer weight</short_desc>
      <min>0</min>
      <max>1</max>
185
      <decimal>2</decimal>
186 187 188 189 190
    </parameter>
    <parameter default="0.1" name="ATT_W_MAG" type="FLOAT">
      <short_desc>Complimentary filter magnetometer weight</short_desc>
      <min>0</min>
      <max>1</max>
191 192 193 194 195 196
      <decimal>2</decimal>
    </parameter>
    <parameter default="0.1" name="ATT_W_EXT_HDG" type="FLOAT">
      <short_desc>Complimentary filter external heading weight</short_desc>
      <min>0</min>
      <max>1</max>
197 198 199 200 201
    </parameter>
    <parameter default="0.1" name="ATT_W_GYRO_BIAS" type="FLOAT">
      <short_desc>Complimentary filter gyroscope bias weight</short_desc>
      <min>0</min>
      <max>1</max>
202
      <decimal>2</decimal>
203 204 205
    </parameter>
    <parameter default="0.0" name="ATT_MAG_DECL" type="FLOAT">
      <short_desc>Magnetic declination, in degrees</short_desc>
Don Gagne's avatar
Don Gagne committed
206
      <long_desc>This parameter is not used in normal operation, as the declination is looked up based on the GPS coordinates of the vehicle.</long_desc>
207
      <unit>degrees</unit>
208
      <decimal>2</decimal>
209 210 211 212 213 214
    </parameter>
    <parameter default="1" name="ATT_MAG_DECL_A" type="INT32">
      <short_desc>Enable automatic GPS based declination compensation</short_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
215 216 217 218 219 220 221
    <parameter default="0" name="ATT_EXT_HDG_M" type="INT32">
      <short_desc>External heading usage mode (from Motion capture/Vision)
Set to 1 to use heading estimate from vision.
Set to 2 to use heading from motion capture</short_desc>
      <min>0</min>
      <max>2</max>
    </parameter>
222 223 224 225 226 227 228 229 230 231 232
    <parameter default="2" name="ATT_ACC_COMP" type="INT32">
      <short_desc>Enable acceleration compensation based on GPS
velocity</short_desc>
      <min>1</min>
      <max>2</max>
    </parameter>
    <parameter default="0.05" name="ATT_BIAS_MAX" type="FLOAT">
      <short_desc>Gyro bias limit</short_desc>
      <min>0</min>
      <max>2</max>
      <unit>rad/s</unit>
233
      <decimal>3</decimal>
234
    </parameter>
Don Gagne's avatar
Don Gagne committed
235 236
    <parameter default="0.2" name="ATT_VIBE_THRESH" type="FLOAT">
      <short_desc>Threshold (of RMS) to warn about high vibration levels</short_desc>
237 238 239
      <min>0.01</min>
      <max>10</max>
      <decimal>2</decimal>
Don Gagne's avatar
Don Gagne committed
240
    </parameter>
241 242 243 244 245 246 247 248 249 250 251 252 253 254
  </group>
  <group name="Battery Calibration">
    <parameter default="3.4" name="BAT_V_EMPTY" type="FLOAT">
      <short_desc>Empty cell voltage</short_desc>
      <long_desc>Defines the voltage where a single cell of the battery is considered empty.</long_desc>
      <unit>V</unit>
    </parameter>
    <parameter default="4.2" name="BAT_V_CHARGED" type="FLOAT">
      <short_desc>Full cell voltage</short_desc>
      <long_desc>Defines the voltage where a single cell of the battery is considered full.</long_desc>
      <unit>V</unit>
    </parameter>
    <parameter default="0.07" name="BAT_V_LOAD_DROP" type="FLOAT">
      <short_desc>Voltage drop per cell on 100% load</short_desc>
Don Gagne's avatar
Don Gagne committed
255 256
      <long_desc>This implicitely defines the internal resistance to maximum current ratio and assumes linearity.</long_desc>
      <min>0.0</min>
257 258 259 260 261
      <unit>V</unit>
    </parameter>
    <parameter default="3" name="BAT_N_CELLS" type="INT32">
      <short_desc>Number of cells</short_desc>
      <long_desc>Defines the number of cells the attached battery consists of.</long_desc>
Don Gagne's avatar
Don Gagne committed
262 263
      <min>1</min>
      <max>10</max>
264 265 266 267 268 269 270
      <unit>S</unit>
    </parameter>
    <parameter default="-1.0" name="BAT_CAPACITY" type="FLOAT">
      <short_desc>Battery capacity</short_desc>
      <long_desc>Defines the capacity of the attached battery.</long_desc>
      <unit>mA</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
271 272 273 274 275
    <parameter default="10000" name="BAT_V_SCALE_IO" type="INT32">
      <short_desc>Scaling factor for battery voltage sensor on PX4IO</short_desc>
      <min>1</min>
      <max>100000</max>
    </parameter>
276
    <parameter default="-1.0" name="BAT_V_SCALING" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313
      <short_desc>Scaling factor for battery voltage sensor on FMU v2</short_desc>
    </parameter>
    <parameter default="0.0124" name="BAT_C_SCALING" type="FLOAT">
      <short_desc>Scaling factor for battery current sensor</short_desc>
    </parameter>
  </group>
  <group name="Camera trigger">
    <parameter default="40.0" name="TRIG_INTERVAL" type="FLOAT">
      <short_desc>Camera trigger interval</short_desc>
      <long_desc>This parameter sets the time between two consecutive trigger events</long_desc>
      <min>4.0</min>
      <max>10000.0</max>
      <unit>milliseconds</unit>
    </parameter>
    <parameter default="0" name="TRIG_POLARITY" type="INT32">
      <short_desc>Camera trigger polarity</short_desc>
      <long_desc>This parameter sets the polarity of the trigger (0 = ACTIVE_LOW, 1 = ACTIVE_HIGH )</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0.5" name="TRIG_ACT_TIME" type="FLOAT">
      <short_desc>Camera trigger activation time</short_desc>
      <long_desc>This parameter sets the time the trigger needs to pulled high or low.</long_desc>
      <unit>milliseconds</unit>
    </parameter>
    <parameter default="0" name="TRIG_MODE" type="INT32">
      <short_desc>Camera trigger mode</short_desc>
      <long_desc>0 disables the trigger, 1 sets it to enabled on command, 2 always on</long_desc>
      <min>0</min>
      <max>2</max>
    </parameter>
    <parameter default="12" name="TRIG_PINS" type="INT32">
      <short_desc>Camera trigger pin</short_desc>
      <long_desc>Selects which pin is used, ranges from 1 to 6 (AUX1-AUX6)</long_desc>
      <min>1</min>
      <max>123456</max>
    </parameter>
314 315 316 317
  </group>
  <group name="Circuit Breaker">
    <parameter default="0" name="CBRK_SUPPLY_CHK" type="INT32">
      <short_desc>Circuit breaker for power supply check</short_desc>
Don Gagne's avatar
Don Gagne committed
318
      <long_desc>Setting this parameter to 894281 will disable the power valid checks in the commander. WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
319 320 321 322 323
      <min>0</min>
      <max>894281</max>
    </parameter>
    <parameter default="0" name="CBRK_RATE_CTRL" type="INT32">
      <short_desc>Circuit breaker for rate controller output</short_desc>
Don Gagne's avatar
Don Gagne committed
324
      <long_desc>Setting this parameter to 140253 will disable the rate controller uORB publication. WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
325 326 327 328 329
      <min>0</min>
      <max>140253</max>
    </parameter>
    <parameter default="0" name="CBRK_IO_SAFETY" type="INT32">
      <short_desc>Circuit breaker for IO safety</short_desc>
Don Gagne's avatar
Don Gagne committed
330
      <long_desc>Setting this parameter to 22027 will disable IO safety. WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
331 332 333 334 335
      <min>0</min>
      <max>22027</max>
    </parameter>
    <parameter default="0" name="CBRK_AIRSPD_CHK" type="INT32">
      <short_desc>Circuit breaker for airspeed sensor</short_desc>
Don Gagne's avatar
Don Gagne committed
336
      <long_desc>Setting this parameter to 162128 will disable the check for an airspeed sensor. WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
337 338 339 340 341
      <min>0</min>
      <max>162128</max>
    </parameter>
    <parameter default="121212" name="CBRK_FLIGHTTERM" type="INT32">
      <short_desc>Circuit breaker for flight termination</short_desc>
Don Gagne's avatar
Don Gagne committed
342
      <long_desc>Setting this parameter to 121212 will disable the flight termination action. --&gt; The IO driver will not do flight termination if requested by the FMU WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
343 344 345 346 347
      <min>0</min>
      <max>121212</max>
    </parameter>
    <parameter default="284953" name="CBRK_ENGINEFAIL" type="INT32">
      <short_desc>Circuit breaker for engine failure detection</short_desc>
Don Gagne's avatar
Don Gagne committed
348
      <long_desc>Setting this parameter to 284953 will disable the engine failure detection. If the aircraft is in engine failure mode the enine failure flag will be set to healthy WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
349 350 351 352 353
      <min>0</min>
      <max>284953</max>
    </parameter>
    <parameter default="240024" name="CBRK_GPSFAIL" type="INT32">
      <short_desc>Circuit breaker for GPS failure detection</short_desc>
Don Gagne's avatar
Don Gagne committed
354
      <long_desc>Setting this parameter to 240024 will disable the GPS failure detection. If this check is enabled, then the sensor check will fail if the GPS module is missing. It will also check for excessive signal noise on the GPS receiver and warn the user if detected. WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
355 356 357
      <min>0</min>
      <max>240024</max>
    </parameter>
358 359 360 361 362 363
    <parameter default="0" name="CBRK_BUZZER" type="INT32">
      <short_desc>Circuit breaker for disabling buzzer</short_desc>
      <long_desc>Setting this parameter to 782097 will disable the buzzer audio notification. WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
      <min>0</min>
      <max>782097</max>
    </parameter>
364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380
  </group>
  <group name="Commander">
    <parameter default="0" name="COM_DL_LOSS_EN" type="INT32">
      <short_desc>Datalink loss mode enabled</short_desc>
      <long_desc>Set to 1 to enable actions triggered when the datalink is lost.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="10" name="COM_DL_LOSS_T" type="INT32">
      <short_desc>Datalink loss time threshold</short_desc>
      <long_desc>After this amount of seconds without datalink the data link lost mode triggers</long_desc>
      <min>0</min>
      <max>30</max>
      <unit>second</unit>
    </parameter>
    <parameter default="0" name="COM_DL_REG_T" type="INT32">
      <short_desc>Datalink regain time threshold</short_desc>
Don Gagne's avatar
Don Gagne committed
381
      <long_desc>After a data link loss: after this this amount of seconds with a healthy datalink the 'datalink loss' flag is set back to false</long_desc>
382 383 384 385 386 387 388 389 390 391 392 393
      <min>0</min>
      <max>30</max>
      <unit>second</unit>
    </parameter>
    <parameter default="0.5" name="COM_EF_THROT" type="FLOAT">
      <short_desc>Engine Failure Throttle Threshold</short_desc>
      <long_desc>Engine failure triggers only above this throttle value</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="5.0" name="COM_EF_C2T" type="FLOAT">
      <short_desc>Engine Failure Current/Throttle Threshold</short_desc>
Don Gagne's avatar
Don Gagne committed
394
      <long_desc>Engine failure triggers only below this current value</long_desc>
395
      <min>0.0</min>
Don Gagne's avatar
Don Gagne committed
396 397
      <max>30.0</max>
      <unit>ampere</unit>
398 399 400
    </parameter>
    <parameter default="10.0" name="COM_EF_TIME" type="FLOAT">
      <short_desc>Engine Failure Time Threshold</short_desc>
Don Gagne's avatar
Don Gagne committed
401
      <long_desc>Engine failure triggers only if the throttle threshold and the current to throttle threshold are violated for this time</long_desc>
402
      <min>0.0</min>
Don Gagne's avatar
Don Gagne committed
403
      <max>60.0</max>
404 405 406 407 408 409 410 411 412
      <unit>second</unit>
    </parameter>
    <parameter default="0.5" name="COM_RC_LOSS_T" type="FLOAT">
      <short_desc>RC loss time threshold</short_desc>
      <long_desc>After this amount of seconds without RC connection the rc lost flag is set to true</long_desc>
      <min>0</min>
      <max>35</max>
      <unit>second</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
413 414 415 416 417 418 419 420 421 422 423 424 425 426
    <parameter default="5.0" name="COM_HOME_H_T" type="FLOAT">
      <short_desc>Home set horizontal threshold</short_desc>
      <long_desc>The home position will be set if the estimated positioning accuracy is below the threshold.</long_desc>
      <min>2</min>
      <max>15</max>
      <unit>meter</unit>
    </parameter>
    <parameter default="10.0" name="COM_HOME_V_T" type="FLOAT">
      <short_desc>Home set vertical threshold</short_desc>
      <long_desc>The home position will be set if the estimated positioning accuracy is below the threshold.</long_desc>
      <min>5</min>
      <max>25</max>
      <unit>meter</unit>
    </parameter>
427 428
    <parameter default="1" name="COM_AUTOS_PAR" type="INT32">
      <short_desc>Autosaving of params</short_desc>
Don Gagne's avatar
Don Gagne committed
429
      <long_desc>If not equal to zero the commander will automatically save parameters to persistent storage once changed. Default is on, as the interoperability with currently deployed GCS solutions depends on parameters being sticky. Developers can default it to off.</long_desc>
430 431 432 433 434
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="COM_RC_IN_MODE" type="INT32">
      <short_desc>RC control input mode</short_desc>
Don Gagne's avatar
Don Gagne committed
435
      <long_desc>The default value of 0 requires a valid RC transmitter setup. Setting this to 1 disables RC input handling and the associated checks. A value of 2 will generate RC control data from manual input received via MAVLink instead of directly forwarding the manual input data.</long_desc>
436 437 438
      <min>0</min>
      <max>2</max>
    </parameter>
439 440 441 442 443
    <parameter default="0" name="COM_DISARM_LAND" type="INT32">
      <short_desc>Time-out for auto disarm after landing</short_desc>
      <long_desc>A non-zero, positive value specifies the time-out period in seconds after which the vehicle will be automatically disarmed in case a landing situation has been detected during this period. A value of zero means that automatic disarming is disabled.</long_desc>
      <min>0</min>
    </parameter>
444 445 446 447 448 449 450 451 452 453 454
  </group>
  <group name="Data Link Loss">
    <parameter default="120.0" name="NAV_DLL_CH_T" type="FLOAT">
      <short_desc>Comms hold wait time</short_desc>
      <long_desc>The amount of time in seconds the system should wait at the comms hold waypoint</long_desc>
      <min>0.0</min>
      <unit>seconds</unit>
    </parameter>
    <parameter default="-266072120" name="NAV_DLL_CH_LAT" type="INT32">
      <short_desc>Comms hold Lat</short_desc>
      <long_desc>Latitude of comms hold waypoint</long_desc>
Don Gagne's avatar
Don Gagne committed
455 456
      <min>-900000000</min>
      <max>900000000</max>
457 458 459 460 461
      <unit>degrees * 1e7</unit>
    </parameter>
    <parameter default="1518453890" name="NAV_DLL_CH_LON" type="INT32">
      <short_desc>Comms hold Lon</short_desc>
      <long_desc>Longitude of comms hold waypoint</long_desc>
Don Gagne's avatar
Don Gagne committed
462 463
      <min>-1800000000</min>
      <max>1800000000</max>
464 465 466 467 468
      <unit>degrees * 1e7</unit>
    </parameter>
    <parameter default="600.0" name="NAV_DLL_CH_ALT" type="FLOAT">
      <short_desc>Comms hold alt</short_desc>
      <long_desc>Altitude of comms hold waypoint</long_desc>
Don Gagne's avatar
Don Gagne committed
469 470
      <min>-50</min>
      <max>30000</max>
471 472 473
      <unit>m</unit>
    </parameter>
    <parameter default="120.0" name="NAV_DLL_AH_T" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
474
      <short_desc>Airfield hole wait time</short_desc>
475 476 477 478 479 480 481 482 483 484 485 486
      <long_desc>The amount of time in seconds the system should wait at the airfield home waypoint</long_desc>
      <min>0.0</min>
      <unit>seconds</unit>
    </parameter>
    <parameter default="2" name="NAV_DLL_N" type="INT32">
      <short_desc>Number of allowed Datalink timeouts</short_desc>
      <long_desc>After more than this number of data link timeouts the aircraft returns home directly</long_desc>
      <min>0</min>
      <max>1000</max>
    </parameter>
    <parameter default="0" name="NAV_DLL_CHSK" type="INT32">
      <short_desc>Skip comms hold wp</short_desc>
Don Gagne's avatar
Don Gagne committed
487
      <long_desc>If set to 1 the system will skip the comms hold wp on data link loss and will directly fly to airfield home</long_desc>
488 489 490
      <min>0</min>
      <max>1</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510
    <parameter default="-265847810" name="NAV_AH_LAT" type="INT32">
      <short_desc>Airfield home Lat</short_desc>
      <long_desc>Latitude of airfield home waypoint</long_desc>
      <min>-900000000</min>
      <max>900000000</max>
      <unit>degrees * 1e7</unit>
    </parameter>
    <parameter default="1518423250" name="NAV_AH_LON" type="INT32">
      <short_desc>Airfield home Lon</short_desc>
      <long_desc>Longitude of airfield home waypoint</long_desc>
      <min>-1800000000</min>
      <max>1800000000</max>
      <unit>degrees * 1e7</unit>
    </parameter>
    <parameter default="600.0" name="NAV_AH_ALT" type="FLOAT">
      <short_desc>Airfield home alt</short_desc>
      <long_desc>Altitude of airfield home waypoint</long_desc>
      <min>-50</min>
      <unit>m</unit>
    </parameter>
511 512
  </group>
  <group name="FW Attitude Control">
Don Gagne's avatar
Don Gagne committed
513
    <parameter default="0.4" name="FW_ATT_TC" type="FLOAT">
514
      <short_desc>Attitude Time Constant</short_desc>
Don Gagne's avatar
Don Gagne committed
515
      <long_desc>This defines the latency between a step input and the achieved setpoint (inverse to a P gain). Half a second is a good start value and fits for most average systems. Smaller systems may require smaller values, but as this will wear out servos faster, the value should only be decreased as needed.</long_desc>
516 517 518 519
      <min>0.4</min>
      <max>1.0</max>
      <unit>seconds</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
520
    <parameter default="0.08" name="FW_PR_P" type="FLOAT">
521
      <short_desc>Pitch rate proportional gain</short_desc>
Don Gagne's avatar
Don Gagne committed
522
      <long_desc>This defines how much the elevator input will be commanded depending on the current body angular rate error.</long_desc>
523 524 525
      <min>0.005</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
526
    <parameter default="0.02" name="FW_PR_I" type="FLOAT">
527
      <short_desc>Pitch rate integrator gain</short_desc>
Don Gagne's avatar
Don Gagne committed
528 529 530
      <long_desc>This gain defines how much control response will result out of a steady state error. It trims any constant error.</long_desc>
      <min>0.005</min>
      <max>0.5</max>
531
    </parameter>
Don Gagne's avatar
Don Gagne committed
532
    <parameter default="60.0" name="FW_P_RMAX_POS" type="FLOAT">
533
      <short_desc>Maximum positive / up pitch rate</short_desc>
Don Gagne's avatar
Don Gagne committed
534
      <long_desc>This limits the maximum pitch up angular rate the controller will output (in degrees per second). Setting a value of zero disables the limit.</long_desc>
535 536 537 538
      <min>0.0</min>
      <max>90.0</max>
      <unit>deg/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
539
    <parameter default="60.0" name="FW_P_RMAX_NEG" type="FLOAT">
540
      <short_desc>Maximum negative / down pitch rate</short_desc>
Don Gagne's avatar
Don Gagne committed
541
      <long_desc>This limits the maximum pitch down up angular rate the controller will output (in degrees per second). Setting a value of zero disables the limit.</long_desc>
542 543 544 545
      <min>0.0</min>
      <max>90.0</max>
      <unit>deg/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
546
    <parameter default="0.4" name="FW_PR_IMAX" type="FLOAT">
547
      <short_desc>Pitch rate integrator limit</short_desc>
Don Gagne's avatar
Don Gagne committed
548
      <long_desc>The portion of the integrator part in the control surface deflection is limited to this value</long_desc>
549 550 551 552 553
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="0.05" name="FW_RR_P" type="FLOAT">
      <short_desc>Roll rate proportional Gain</short_desc>
Don Gagne's avatar
Don Gagne committed
554
      <long_desc>This defines how much the aileron input will be commanded depending on the current body angular rate error.</long_desc>
555 556 557
      <min>0.005</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
558
    <parameter default="0.01" name="FW_RR_I" type="FLOAT">
559
      <short_desc>Roll rate integrator Gain</short_desc>
Don Gagne's avatar
Don Gagne committed
560 561 562
      <long_desc>This gain defines how much control response will result out of a steady state error. It trims any constant error.</long_desc>
      <min>0.005</min>
      <max>0.2</max>
563 564 565 566 567 568 569
    </parameter>
    <parameter default="0.2" name="FW_RR_IMAX" type="FLOAT">
      <short_desc>Roll Integrator Anti-Windup</short_desc>
      <long_desc>The portion of the integrator part in the control surface deflection is limited to this value.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
570
    <parameter default="70.0" name="FW_R_RMAX" type="FLOAT">
571
      <short_desc>Maximum Roll Rate</short_desc>
Don Gagne's avatar
Don Gagne committed
572
      <long_desc>This limits the maximum roll rate the controller will output (in degrees per second). Setting a value of zero disables the limit.</long_desc>
573 574 575 576 577 578
      <min>0.0</min>
      <max>90.0</max>
      <unit>deg/s</unit>
    </parameter>
    <parameter default="0.05" name="FW_YR_P" type="FLOAT">
      <short_desc>Yaw rate proportional gain</short_desc>
Don Gagne's avatar
Don Gagne committed
579
      <long_desc>This defines how much the rudder input will be commanded depending on the current body angular rate error.</long_desc>
580 581 582 583 584
      <min>0.005</min>
      <max>1.0</max>
    </parameter>
    <parameter default="0.0" name="FW_YR_I" type="FLOAT">
      <short_desc>Yaw rate integrator gain</short_desc>
Don Gagne's avatar
Don Gagne committed
585
      <long_desc>This gain defines how much control response will result out of a steady state error. It trims any constant error.</long_desc>
586 587 588 589 590
      <min>0.0</min>
      <max>50.0</max>
    </parameter>
    <parameter default="0.2" name="FW_YR_IMAX" type="FLOAT">
      <short_desc>Yaw rate integrator limit</short_desc>
Don Gagne's avatar
Don Gagne committed
591
      <long_desc>The portion of the integrator part in the control surface deflection is limited to this value</long_desc>
592 593 594 595 596
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="0.0" name="FW_Y_RMAX" type="FLOAT">
      <short_desc>Maximum Yaw Rate</short_desc>
Don Gagne's avatar
Don Gagne committed
597
      <long_desc>This limits the maximum yaw rate the controller will output (in degrees per second). Setting a value of zero disables the limit.</long_desc>
598 599 600 601
      <min>0.0</min>
      <max>90.0</max>
      <unit>deg/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
602
    <parameter default="0.5" name="FW_RR_FF" type="FLOAT">
603
      <short_desc>Roll rate feed forward</short_desc>
Don Gagne's avatar
Don Gagne committed
604
      <long_desc>Direct feed forward from rate setpoint to control surface output. Use this to obtain a tigher response of the controller without introducing noise amplification.</long_desc>
605 606 607
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
608
    <parameter default="0.5" name="FW_PR_FF" type="FLOAT">
609 610 611 612 613 614 615 616 617 618 619 620 621
      <short_desc>Pitch rate feed forward</short_desc>
      <long_desc>Direct feed forward from rate setpoint to control surface output</long_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.3" name="FW_YR_FF" type="FLOAT">
      <short_desc>Yaw rate feed forward</short_desc>
      <long_desc>Direct feed forward from rate setpoint to control surface output</long_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="1000.0" name="FW_YCO_VMIN" type="FLOAT">
      <short_desc>Minimal speed for yaw coordination</short_desc>
Don Gagne's avatar
Don Gagne committed
622
      <long_desc>For airspeeds above this value, the yaw rate is calculated for a coordinated turn. Set to a very high value to disable.</long_desc>
623 624 625 626
      <unit>m/s</unit>
    </parameter>
    <parameter default="0" name="FW_YCO_METHOD" type="INT32">
      <short_desc>Method used for yaw coordination</short_desc>
Don Gagne's avatar
Don Gagne committed
627
      <long_desc>The param value sets the method used to calculate the yaw rate 0: open-loop zero lateral acceleration based on kinematic constraints 1: closed-loop: try to reduce lateral acceleration to 0 by measuring the acceleration</long_desc>
628 629 630 631 632 633
      <min>0</min>
      <max>1</max>
      <unit>m/s</unit>
    </parameter>
    <parameter default="10.0" name="FW_AIRSPD_MIN" type="FLOAT">
      <short_desc>Minimum Airspeed</short_desc>
Don Gagne's avatar
Don Gagne committed
634
      <long_desc>If the airspeed falls below this value, the TECS controller will try to increase airspeed more aggressively.</long_desc>
635 636 637 638 639 640 641 642 643 644 645 646 647
      <min>0.0</min>
      <max>40</max>
      <unit>m/s</unit>
    </parameter>
    <parameter default="15.0" name="FW_AIRSPD_TRIM" type="FLOAT">
      <short_desc>Trim Airspeed</short_desc>
      <long_desc>The TECS controller tries to fly at this airspeed.</long_desc>
      <min>0.0</min>
      <max>40</max>
      <unit>m/s</unit>
    </parameter>
    <parameter default="20.0" name="FW_AIRSPD_MAX" type="FLOAT">
      <short_desc>Maximum Airspeed</short_desc>
Don Gagne's avatar
Don Gagne committed
648
      <long_desc>If the airspeed is above this value, the TECS controller will try to decrease airspeed more aggressively.</long_desc>
649 650 651 652 653 654
      <min>0.0</min>
      <max>40</max>
      <unit>m/s</unit>
    </parameter>
    <parameter default="0.0" name="FW_RSP_OFF" type="FLOAT">
      <short_desc>Roll Setpoint Offset</short_desc>
Don Gagne's avatar
Don Gagne committed
655
      <long_desc>An airframe specific offset of the roll setpoint in degrees, the value is added to the roll setpoint and should correspond to the typical cruise speed of the airframe.</long_desc>
656 657 658 659 660 661
      <min>-90.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="0.0" name="FW_PSP_OFF" type="FLOAT">
      <short_desc>Pitch Setpoint Offset</short_desc>
Don Gagne's avatar
Don Gagne committed
662
      <long_desc>An airframe specific offset of the pitch setpoint in degrees, the value is added to the pitch setpoint and should correspond to the typical cruise speed of the airframe.</long_desc>
663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684
      <min>-90.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="45.0" name="FW_MAN_R_MAX" type="FLOAT">
      <short_desc>Max Manual Roll</short_desc>
      <long_desc>Max roll for manual control in attitude stabilized mode</long_desc>
      <min>0.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="45.0" name="FW_MAN_P_MAX" type="FLOAT">
      <short_desc>Max Manual Pitch</short_desc>
      <long_desc>Max pitch for manual control in attitude stabilized mode</long_desc>
      <min>0.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
  </group>
  <group name="Fixed Wing TECS">
    <parameter default="2.0" name="FW_T_SINK_MIN" type="FLOAT">
      <short_desc>Minimum descent rate</short_desc>
Don Gagne's avatar
Don Gagne committed
685
      <long_desc>This is the sink rate of the aircraft with the throttle set to THR_MIN and flown at the same airspeed as used to measure FW_T_CLMB_MAX.</long_desc>
686 687 688
    </parameter>
    <parameter default="5.0" name="FW_T_SINK_MAX" type="FLOAT">
      <short_desc>Maximum descent rate</short_desc>
Don Gagne's avatar
Don Gagne committed
689
      <long_desc>This sets the maximum descent rate that the controller will use. If this value is too large, the aircraft can over-speed on descent. This should be set to a value that can be achieved without exceeding the lower pitch angle limit and without over-speeding the aircraft.</long_desc>
690 691 692
    </parameter>
    <parameter default="5.0" name="FW_T_TIME_CONST" type="FLOAT">
      <short_desc>TECS time constant</short_desc>
Don Gagne's avatar
Don Gagne committed
693
      <long_desc>This is the time constant of the TECS control algorithm (in seconds). Smaller values make it faster to respond, larger values make it slower to respond.</long_desc>
694 695 696
    </parameter>
    <parameter default="8.0" name="FW_T_THRO_CONST" type="FLOAT">
      <short_desc>TECS Throttle time constant</short_desc>
Don Gagne's avatar
Don Gagne committed
697
      <long_desc>This is the time constant of the TECS throttle control algorithm (in seconds). Smaller values make it faster to respond, larger values make it slower to respond.</long_desc>
698 699 700
    </parameter>
    <parameter default="0.5" name="FW_T_THR_DAMP" type="FLOAT">
      <short_desc>Throttle damping factor</short_desc>
Don Gagne's avatar
Don Gagne committed
701
      <long_desc>This is the damping gain for the throttle demand loop. Increase to add damping to correct for oscillations in speed and height.</long_desc>
702 703 704
    </parameter>
    <parameter default="0.1" name="FW_T_INTEG_GAIN" type="FLOAT">
      <short_desc>Integrator gain</short_desc>
Don Gagne's avatar
Don Gagne committed
705
      <long_desc>This is the integrator gain on the control loop. Increasing this gain increases the speed at which speed and height offsets are trimmed out, but reduces damping and increases overshoot.</long_desc>
706 707 708
    </parameter>
    <parameter default="7.0" name="FW_T_VERT_ACC" type="FLOAT">
      <short_desc>Maximum vertical acceleration</short_desc>
Don Gagne's avatar
Don Gagne committed
709
      <long_desc>This is the maximum vertical acceleration (in metres/second square) either up or down that the controller will use to correct speed or height errors. The default value of 7 m/s/s (equivalent to +- 0.7 g) allows for reasonably aggressive pitch changes if required to recover from under-speed conditions.</long_desc>
710 711 712
    </parameter>
    <parameter default="3.0" name="FW_T_HGT_OMEGA" type="FLOAT">
      <short_desc>Complementary filter "omega" parameter for height</short_desc>
Don Gagne's avatar
Don Gagne committed
713
      <long_desc>This is the cross-over frequency (in radians/second) of the complementary filter used to fuse vertical acceleration and barometric height to obtain an estimate of height rate and height. Increasing this frequency weights the solution more towards use of the barometer, whilst reducing it weights the solution more towards use of the accelerometer data.</long_desc>
714 715 716
    </parameter>
    <parameter default="2.0" name="FW_T_SPD_OMEGA" type="FLOAT">
      <short_desc>Complementary filter "omega" parameter for speed</short_desc>
Don Gagne's avatar
Don Gagne committed
717
      <long_desc>This is the cross-over frequency (in radians/second) of the complementary filter used to fuse longitudinal acceleration and airspeed to obtain an improved airspeed estimate. Increasing this frequency weights the solution more towards use of the arispeed sensor, whilst reducing it weights the solution more towards use of the accelerometer data.</long_desc>
718
    </parameter>
Don Gagne's avatar
Don Gagne committed
719
    <parameter default="15.0" name="FW_T_RLL2THR" type="FLOAT">
720
      <short_desc>Roll -&gt; Throttle feedforward</short_desc>
Don Gagne's avatar
Don Gagne committed
721
      <long_desc>Increasing this gain turn increases the amount of throttle that will be used to compensate for the additional drag created by turning. Ideally this should be set to  approximately 10 x the extra sink rate in m/s created by a 45 degree bank turn. Increase this gain if the aircraft initially loses energy in turns and reduce if the aircraft initially gains energy in turns. Efficient high aspect-ratio aircraft (eg powered sailplanes) can use a lower value, whereas inefficient low aspect-ratio models (eg delta wings) can use a higher value.</long_desc>
722 723 724
    </parameter>
    <parameter default="1.0" name="FW_T_SPDWEIGHT" type="FLOAT">
      <short_desc>Speed &lt;--&gt; Altitude priority</short_desc>
Don Gagne's avatar
Don Gagne committed
725
      <long_desc>This parameter adjusts the amount of weighting that the pitch control applies to speed vs height errors. Setting it to 0.0 will cause the pitch control to control height and ignore speed errors. This will normally improve height accuracy but give larger airspeed errors. Setting it to 2.0 will cause the pitch control loop to control speed and ignore height errors. This will normally reduce airspeed errors, but give larger height errors. The default value of 1.0 allows the pitch control to simultaneously control height and speed. Note to Glider Pilots - set this parameter to 2.0 (The glider will adjust its pitch angle to maintain airspeed, ignoring changes in height).</long_desc>
726 727 728
    </parameter>
    <parameter default="0.0" name="FW_T_PTCH_DAMP" type="FLOAT">
      <short_desc>Pitch damping factor</short_desc>
Don Gagne's avatar
Don Gagne committed
729
      <long_desc>This is the damping gain for the pitch demand loop. Increase to add damping to correct for oscillations in height. The default value of 0.0 will work well provided the pitch to servo controller has been tuned properly.</long_desc>
730 731 732 733 734 735 736
    </parameter>
    <parameter default="0.05" name="FW_T_HRATE_P" type="FLOAT">
      <short_desc>Height rate P factor</short_desc>
    </parameter>
    <parameter default="0.0" name="FW_T_HRATE_FF" type="FLOAT">
      <short_desc>Height rate FF factor</short_desc>
    </parameter>
Don Gagne's avatar
Don Gagne committed
737
    <parameter default="0.02" name="FW_T_SRATE_P" type="FLOAT">
738 739 740 741 742 743
      <short_desc>Speed rate P factor</short_desc>
    </parameter>
  </group>
  <group name="GPS Failure Navigation">
    <parameter default="30.0" name="NAV_GPSF_LT" type="FLOAT">
      <short_desc>Loiter time</short_desc>
Don Gagne's avatar
Don Gagne committed
744
      <long_desc>The amount of time in seconds the system should do open loop loiter and wait for gps recovery before it goes into flight termination.</long_desc>
745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769
      <min>0.0</min>
      <unit>seconds</unit>
    </parameter>
    <parameter default="15.0" name="NAV_GPSF_R" type="FLOAT">
      <short_desc>Open loop loiter roll</short_desc>
      <long_desc>Roll in degrees during the open loop loiter</long_desc>
      <min>0.0</min>
      <max>30.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="0.0" name="NAV_GPSF_P" type="FLOAT">
      <short_desc>Open loop loiter pitch</short_desc>
      <long_desc>Pitch in degrees during the open loop loiter</long_desc>
      <min>-30.0</min>
      <max>30.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="0.7" name="NAV_GPSF_TR" type="FLOAT">
      <short_desc>Open loop loiter thrust</short_desc>
      <long_desc>Thrust value which is set during the open loop loiter</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
  </group>
  <group name="Geofence">
770 771 772
    <parameter default="1" name="GF_ACTION" type="INT32">
      <short_desc>Geofence violation action</short_desc>
      <long_desc>0 = none, 1 = warning (default), 2 = loiter, 3 = return to launch, 4 = fight termination</long_desc>
773
      <min>0</min>
774
      <max>4</max>
775 776 777
    </parameter>
    <parameter default="0" name="GF_ALTMODE" type="INT32">
      <short_desc>Geofence altitude mode</short_desc>
Don Gagne's avatar
Don Gagne committed
778
      <long_desc>Select which altitude reference should be used 0 = WGS84, 1 = AMSL</long_desc>
779 780 781 782 783
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="GF_SOURCE" type="INT32">
      <short_desc>Geofence source</short_desc>
Don Gagne's avatar
Don Gagne committed
784
      <long_desc>Select which position source should be used. Selecting GPS instead of global position makes sure that there is no dependence on the position estimator 0 = global position, 1 = GPS</long_desc>
785 786 787 788 789 790 791 792 793 794 795
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="-1" name="GF_COUNT" type="INT32">
      <short_desc>Geofence counter limit</short_desc>
      <long_desc>Set how many subsequent position measurements outside of the fence are needed before geofence violation is triggered</long_desc>
      <min>-1</min>
      <max>10</max>
    </parameter>
    <parameter default="-1" name="GF_MAX_HOR_DIST" type="INT32">
      <short_desc>Max horizontal distance in meters</short_desc>
796
      <long_desc>Set to &gt; 0 to activate a geofence action if horizontal distance to home exceeds this value.</long_desc>
797 798 799
    </parameter>
    <parameter default="-1" name="GF_MAX_VER_DIST" type="INT32">
      <short_desc>Max vertical distance in meters</short_desc>
800
      <long_desc>Set to &gt; 0 to activate a geofence action if vertical distance to home exceeds this value.</long_desc>
801 802 803
    </parameter>
  </group>
  <group name="L1 Control">
Don Gagne's avatar
Don Gagne committed
804
    <parameter default="20.0" name="FW_L1_PERIOD" type="FLOAT">
805
      <short_desc>L1 period</short_desc>
Don Gagne's avatar
Don Gagne committed
806
      <long_desc>This is the L1 distance and defines the tracking point ahead of the aircraft its following. A value of 25 meters works for most aircraft. Shorten slowly during tuning until response is sharp without oscillation.</long_desc>
807 808 809 810 811 812 813 814 815
      <min>1.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="0.75" name="FW_L1_DAMPING" type="FLOAT">
      <short_desc>L1 damping</short_desc>
      <long_desc>Damping factor for L1 control.</long_desc>
      <min>0.6</min>
      <max>0.9</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
816
    <parameter default="0.6" name="FW_THR_CRUISE" type="FLOAT">
817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841
      <short_desc>Cruise throttle</short_desc>
      <long_desc>This is the throttle setting required to achieve the desired cruise speed. Most airframes have a value of 0.5-0.7.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="0.0" name="FW_THR_SLEW_MAX" type="FLOAT">
      <short_desc>Throttle max slew rate</short_desc>
      <long_desc>Maximum slew rate for the commanded throttle</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="-45.0" name="FW_P_LIM_MIN" type="FLOAT">
      <short_desc>Negative pitch limit</short_desc>
      <long_desc>The minimum negative pitch the controller will output.</long_desc>
      <min>-60.0</min>
      <max>0.0</max>
      <unit>degrees</unit>
    </parameter>
    <parameter default="45.0" name="FW_P_LIM_MAX" type="FLOAT">
      <short_desc>Positive pitch limit</short_desc>
      <long_desc>The maximum positive pitch the controller will output.</long_desc>
      <min>0.0</min>
      <max>60.0</max>
      <unit>degrees</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
842
    <parameter default="50.0" name="FW_R_LIM" type="FLOAT">
843 844
      <short_desc>Controller roll limit</short_desc>
      <long_desc>The maximum roll the controller will output.</long_desc>
Don Gagne's avatar
Don Gagne committed
845 846
      <min>35.0</min>
      <max>65.0</max>
847 848 849 850
      <unit>degrees</unit>
    </parameter>
    <parameter default="1.0" name="FW_THR_MAX" type="FLOAT">
      <short_desc>Throttle limit max</short_desc>
Don Gagne's avatar
Don Gagne committed
851
      <long_desc>This is the maximum throttle % that can be used by the controller. For overpowered aircraft, this should be reduced to a value that provides sufficient thrust to climb at the maximum pitch angle PTCH_MAX.</long_desc>
852 853 854
    </parameter>
    <parameter default="0.0" name="FW_THR_MIN" type="FLOAT">
      <short_desc>Throttle limit min</short_desc>
Don Gagne's avatar
Don Gagne committed
855 856 857
      <long_desc>This is the minimum throttle % that can be used by the controller. For electric aircraft this will normally be set to zero, but can be set to a small non-zero value if a folding prop is fitted to prevent the prop from folding and unfolding repeatedly in-flight or to provide some aerodynamic drag from a turning prop to improve the descent rate. For aircraft with internal combustion engine this parameter should be set for desired idle rpm.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
858 859 860
    </parameter>
    <parameter default="1.0" name="FW_THR_LND_MAX" type="FLOAT">
      <short_desc>Throttle limit value before flare</short_desc>
Don Gagne's avatar
Don Gagne committed
861 862 863
      <long_desc>This throttle value will be set as throttle limit at FW_LND_TLALT, before arcraft will flare.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
864
    </parameter>
865
    <parameter default="10.0" name="FW_CLMBOUT_DIFF" type="FLOAT">
866
      <short_desc>Climbout Altitude difference</short_desc>
Don Gagne's avatar
Don Gagne committed
867 868 869
      <long_desc>If the altitude error exceeds this parameter, the system will climb out with maximum throttle and minimum airspeed until it is closer than this distance to the desired altitude. Mostly used for takeoff waypoints / modes. Set to zero to disable climbout mode (not recommended).</long_desc>
      <min>0.0</min>
      <max>150.0</max>
870 871 872
    </parameter>
    <parameter default="5.0" name="FW_T_CLMB_MAX" type="FLOAT">
      <short_desc>Maximum climb rate</short_desc>
Don Gagne's avatar
Don Gagne committed
873 874 875
      <long_desc>This is the best climb rate that the aircraft can achieve with the throttle set to THR_MAX and the airspeed set to the default value. For electric aircraft make sure this number can be achieved towards the end of flight when the battery voltage has reduced. The setting of this parameter can be checked by commanding a positive altitude change of 100m in loiter, RTL or guided mode. If the throttle required to climb is close to THR_MAX and the aircraft is maintaining airspeed, then this parameter is set correctly. If the airspeed starts to reduce, then the parameter is set to high, and if the throttle demand required to climb and maintain speed is noticeably less than FW_THR_MAX, then either FW_T_CLMB_MAX should be increased or FW_THR_MAX reduced.</long_desc>
      <min>2.0</min>
      <max>10.0</max>
876 877 878 879 880 881 882 883 884 885 886 887 888
    </parameter>
    <parameter default="5.0" name="FW_LND_ANG" type="FLOAT">
      <short_desc>Landing slope angle</short_desc>
    </parameter>
    <parameter default="10.0" name="FW_LND_HVIRT" type="FLOAT">
      <short_desc>FW_LND_HVIRT</short_desc>
    </parameter>
    <parameter default="8.0" name="FW_LND_FLALT" type="FLOAT">
      <short_desc>Landing flare altitude (relative to landing altitude)</short_desc>
      <unit>meter</unit>
    </parameter>
    <parameter default="-1.0" name="FW_LND_TLALT" type="FLOAT">
      <short_desc>Landing throttle limit altitude (relative landing altitude)</short_desc>
Don Gagne's avatar
Don Gagne committed
889
      <long_desc>Default of -1.0f lets the system default to applying throttle limiting at 2/3 of the flare altitude.</long_desc>
890 891 892 893 894 895 896 897 898 899 900
      <unit>meter</unit>
    </parameter>
    <parameter default="15.0" name="FW_LND_HHDIST" type="FLOAT">
      <short_desc>Landing heading hold horizontal distance</short_desc>
    </parameter>
    <parameter default="0" name="FW_LND_USETER" type="INT32">
      <short_desc>Enable or disable usage of terrain estimate during landing</short_desc>
      <long_desc>0: disabled, 1: enabled</long_desc>
    </parameter>
  </group>
  <group name="Land Detector">
Don Gagne's avatar
Don Gagne committed
901
    <parameter default="0.70" name="LNDMC_Z_VEL_MAX" type="FLOAT">
902
      <short_desc>Multicopter max climb rate</short_desc>
Don Gagne's avatar
Don Gagne committed
903 904
      <long_desc>Maximum vertical velocity allowed in the landed state (m/s up and down)</long_desc>
      <unit>m/s</unit>
905
    </parameter>
Don Gagne's avatar
Don Gagne committed
906
    <parameter default="1.50" name="LNDMC_XY_VEL_MAX" type="FLOAT">
907
      <short_desc>Multicopter max horizontal velocity</short_desc>
Don Gagne's avatar
Don Gagne committed
908 909
      <long_desc>Maximum horizontal velocity allowed in the landed state (m/s)</long_desc>
      <unit>m/s</unit>
910 911 912
    </parameter>
    <parameter default="20.0" name="LNDMC_ROT_MAX" type="FLOAT">
      <short_desc>Multicopter max rotation</short_desc>
Don Gagne's avatar
Don Gagne committed
913 914
      <long_desc>Maximum allowed around each axis allowed in the landed state (degrees per second)</long_desc>
      <unit>deg/s</unit>
915
    </parameter>
Don Gagne's avatar
Don Gagne committed
916
    <parameter default="0.15" name="LNDMC_THR_MAX" type="FLOAT">
917
      <short_desc>Multicopter max throttle</short_desc>
Don Gagne's avatar
Don Gagne committed
918 919 920
      <long_desc>Maximum actuator output on throttle allowed in the landed state</long_desc>
      <min>0.1</min>
      <max>0.5</max>
921
    </parameter>
Don Gagne's avatar
Don Gagne committed
922
    <parameter default="5.0" name="LNDFW_VEL_XY_MAX" type="FLOAT">
923
      <short_desc>Fixedwing max horizontal velocity</short_desc>
Don Gagne's avatar
Don Gagne committed
924 925 926 927
      <long_desc>Maximum horizontal velocity allowed in the landed state (m/s)</long_desc>
      <min>0.5</min>
      <max>10</max>
      <unit>m/s</unit>
928
    </parameter>
Don Gagne's avatar
Don Gagne committed
929
    <parameter default="10.0" name="LNDFW_VEL_Z_MAX" type="FLOAT">
930
      <short_desc>Fixedwing max climb rate</short_desc>
Don Gagne's avatar
Don Gagne committed
931 932 933 934
      <long_desc>Maximum vertical velocity allowed in the landed state (m/s up and down)</long_desc>
      <min>5</min>
      <max>20</max>
      <unit>m/s</unit>
935
    </parameter>
Don Gagne's avatar
Don Gagne committed
936
    <parameter default="8.00" name="LNDFW_AIRSPD_MAX" type="FLOAT">
937
      <short_desc>Airspeed max</short_desc>
Don Gagne's avatar
Don Gagne committed
938 939 940 941
      <long_desc>Maximum airspeed allowed in the landed state (m/s)</long_desc>
      <min>4</min>
      <max>20</max>
      <unit>m/s</unit>
942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961
    </parameter>
  </group>
  <group name="Launch detection">
    <parameter default="0" name="LAUN_ALL_ON" type="INT32">
      <short_desc>Enable launch detection</short_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="30.0" name="LAUN_CAT_A" type="FLOAT">
      <short_desc>Catapult accelerometer theshold</short_desc>
      <long_desc>LAUN_CAT_A * LAUN_CAT_T serves as threshold to trigger launch detection.</long_desc>
      <min>0</min>
    </parameter>
    <parameter default="0.05" name="LAUN_CAT_T" type="FLOAT">
      <short_desc>Catapult time theshold</short_desc>
      <long_desc>LAUN_CAT_A * LAUN_CAT_T serves as threshold to trigger launch detection.</long_desc>
      <min>0</min>
    </parameter>
    <parameter default="0.0" name="LAUN_CAT_MDEL" type="FLOAT">
      <short_desc>Motor delay</short_desc>
Don Gagne's avatar
Don Gagne committed
962
      <long_desc>Delay between starting attitude control and powering up the throttle (giving throttle control to the controller) Before this timespan is up the throttle will be set to LAUN_THR_PRE, set to 0 to deactivate</long_desc>
963 964 965 966 967
      <min>0</min>
      <unit>seconds</unit>
    </parameter>
    <parameter default="30.0" name="LAUN_CAT_PMAX" type="FLOAT">
      <short_desc>Maximum pitch before the throttle is powered up (during motor delay phase)</short_desc>
Don Gagne's avatar
Don Gagne committed
968
      <long_desc>This is an extra limit for the maximum pitch which is imposed in the phase before the throttle turns on. This allows to limit the maximum pitch angle during a bungee launch (make the launch less steep).</long_desc>
969 970 971 972 973 974 975 976 977 978 979
      <min>0</min>
      <max>45</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="0.0" name="LAUN_THR_PRE" type="FLOAT">
      <short_desc>Throttle setting while detecting launch</short_desc>
      <long_desc>The throttle is set to this value while the system is waiting for the take-off.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
  </group>
980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104
  <group name="Local Position Estimator">
    <parameter default="1" name="LPE_ENABLED" type="INT32">
      <short_desc>Enable local position estimator</short_desc>
    </parameter>
    <parameter default="1" name="LPE_INTEGRATE" type="INT32">
      <short_desc>Enable accelerometer integration for prediction</short_desc>
    </parameter>
    <parameter default="0.01" name="LPE_FLW_XY" type="FLOAT">
      <short_desc>Optical flow xy standard deviation</short_desc>
      <min>0.01</min>
      <max>1</max>
      <unit>m</unit>
    </parameter>
    <parameter default="0.2" name="LPE_SNR_Z" type="FLOAT">
      <short_desc>Sonar z standard deviation</short_desc>
      <min>0.01</min>
      <max>1</max>
      <unit>m</unit>
    </parameter>
    <parameter default="0.03" name="LPE_LDR_Z" type="FLOAT">
      <short_desc>Lidar z standard deviation</short_desc>
      <min>0.01</min>
      <max>1</max>
      <unit>m</unit>
    </parameter>
    <parameter default="0.0454" name="LPE_ACC_XY" type="FLOAT">
      <short_desc>Accelerometer xy standard deviation</short_desc>
      <long_desc>Data sheet sqrt(Noise power) = 150ug/sqrt(Hz) std dev = (150*9.8*1e-6)*sqrt(1000 Hz) m/s^2 Since accels sampled at 1000 Hz. should be 0.0464</long_desc>
      <min>0.00001</min>
      <max>2</max>
      <unit>m/s^2</unit>
    </parameter>
    <parameter default="0.0454" name="LPE_ACC_Z" type="FLOAT">
      <short_desc>Accelerometer z standard deviation</short_desc>
      <long_desc>(see Accel x comments)</long_desc>
      <min>0.00001</min>
      <max>2</max>
      <unit>m/s^2</unit>
    </parameter>
    <parameter default="1.0" name="LPE_BAR_Z" type="FLOAT">
      <short_desc>Barometric presssure altitude z standard deviation</short_desc>
      <min>0.01</min>
      <max>3</max>
      <unit>m</unit>
    </parameter>
    <parameter default="2.0" name="LPE_GPS_XY" type="FLOAT">
      <short_desc>GPS xy standard deviation</short_desc>
      <min>0.01</min>
      <max>5</max>
      <unit>m</unit>
    </parameter>
    <parameter default="10.0" name="LPE_GPS_Z" type="FLOAT">
      <short_desc>GPS z standard deviation</short_desc>
      <min>0.01</min>
      <max>20</max>
      <unit>m</unit>
    </parameter>
    <parameter default="0.275" name="LPE_GPS_VXY" type="FLOAT">
      <short_desc>GPS xy velocity standard deviation</short_desc>
      <min>0.01</min>
      <max>2</max>
      <unit>m/s</unit>
    </parameter>
    <parameter default="0.237" name="LPE_GPS_VZ" type="FLOAT">
      <short_desc>GPS z velocity standard deviation</short_desc>
      <min>0.01</min>
      <max>2</max>
      <unit>m/s</unit>
    </parameter>
    <parameter default="3.0" name="LPE_EPH_MAX" type="FLOAT">
      <short_desc>GPS max eph</short_desc>
      <min>1.0</min>
      <max>5.0</max>
      <unit>m</unit>
    </parameter>
    <parameter default="0.5" name="LPE_VIS_XY" type="FLOAT">
      <short_desc>Vision xy standard deviation</short_desc>
      <min>0.01</min>
      <max>1</max>
      <unit>m</unit>
    </parameter>
    <parameter default="0.5" name="LPE_VIS_Z" type="FLOAT">
      <short_desc>Vision z standard deviation</short_desc>
      <min>0.01</min>
      <max>2</max>
      <unit>m</unit>
    </parameter>
    <parameter default="0" name="LPE_NO_VISION" type="INT32">
      <short_desc>Circuit breaker to disable vision input</short_desc>
      <long_desc>Set to the appropriate key (328754) to disable vision input.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0.05" name="LPE_VIC_P" type="FLOAT">
      <short_desc>Vicon position standard deviation</short_desc>
      <min>0.01</min>
      <max>1</max>
      <unit>m</unit>
    </parameter>
    <parameter default="0.0" name="LPE_PN_P" type="FLOAT">
      <short_desc>Position propagation process noise power (variance*sampling rate)</short_desc>
      <min>0</min>
      <max>1</max>
      <unit>(m/s^2)-s</unit>
    </parameter>
    <parameter default="0.0" name="LPE_PN_V" type="FLOAT">
      <short_desc>Velocity propagation process noise power (variance*sampling rate)</short_desc>
      <min>0</min>
      <max>5</max>
      <unit>(m/s)-s</unit>
    </parameter>
    <parameter default="1e-8" name="LPE_PN_B" type="FLOAT">
      <short_desc>Accel bias propagation process noise power (variance*sampling rate)</short_desc>
      <min>0</min>
      <max>1</max>
      <unit>(m/s)-s</unit>
    </parameter>
    <parameter default="1000.0" name="LPE_BETA_MAX" type="FLOAT">
      <short_desc>Fault detection threshold, for chi-squared dist</short_desc>
      <long_desc>TODO add separate params for 1 dof, 3 dof, and 6 dof beta or false alarm rate in false alarms/hr</long_desc>
      <min>3</min>
      <max>1000</max>
      <unit />
    </parameter>
  </group>
1105 1106 1107 1108 1109 1110
  <group name="MAVLink">
    <parameter default="1" name="MAV_SYS_ID" type="INT32">
      <short_desc>MAVLink system ID</short_desc>
      <min>1</min>
      <max>250</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1111
    <parameter default="1" name="MAV_COMP_ID" type="INT32">
1112 1113
      <short_desc>MAVLink component ID</short_desc>
      <min>1</min>
Don Gagne's avatar
Don Gagne committed
1114 1115 1116 1117 1118 1119 1120
      <max>250</max>
    </parameter>
    <parameter default="0" name="MAV_RADIO_ID" type="INT32">
      <short_desc>MAVLink Radio ID</short_desc>
      <long_desc>When non-zero the MAVLink app will attempt to configure the radio to this ID and re-set the parameter to 0. If the value is negative it will reset the complete radio config to factory defaults.</long_desc>
      <min>-1</min>
      <max>240</max>
1121
    </parameter>
Don Gagne's avatar
Don Gagne committed
1122 1123 1124
    <parameter default="1" name="MAV_TYPE" type="INT32">
      <short_desc>MAVLink airframe type</short_desc>
      <min>1</min>
1125 1126
    </parameter>
    <parameter default="0" name="MAV_USEHILGPS" type="INT32">
Don Gagne's avatar
Don Gagne committed
1127 1128
      <short_desc>Use/Accept HIL GPS message even if not in HIL mode</short_desc>
      <long_desc>If set to 1 incoming HIL GPS messages are parsed.</long_desc>
1129 1130 1131
    </parameter>
    <parameter default="1" name="MAV_FWDEXTSP" type="INT32">
      <short_desc>Forward external setpoint messages</short_desc>
Don Gagne's avatar
Don Gagne committed
1132
      <long_desc>If set to 1 incoming external setpoint messages will be directly forwarded to the controllers if in offboard control mode</long_desc>
1133 1134 1135
    </parameter>
    <parameter default="1" name="MAV_TEST_PAR" type="INT32">
      <short_desc>Test parameter</short_desc>
Don Gagne's avatar
Don Gagne committed
1136
      <long_desc>This parameter is not actively used by the system. Its purpose is to allow testing the parameter interface on the communication level.</long_desc>
1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148
      <min>-1000</min>
      <max>1000</max>
    </parameter>
  </group>
  <group name="MKBLCTRL Testmode">
    <parameter default="0" name="MKBLCTRL_TEST" type="INT32">
      <short_desc>Enables testmode (Identify) of MKBLCTRL Driver</short_desc>
    </parameter>
  </group>
  <group name="Mission">
    <parameter default="10.0" name="MIS_TAKEOFF_ALT" type="FLOAT">
      <short_desc>Take-off altitude</short_desc>
Don Gagne's avatar
Don Gagne committed
1149
      <long_desc>Even if first waypoint has altitude less then MIS_TAKEOFF_ALT above home position, system will climb to MIS_TAKEOFF_ALT on takeoff, then go to waypoint.</long_desc>
1150 1151 1152 1153
      <unit>meters</unit>
    </parameter>
    <parameter default="1" name="MIS_ONBOARD_EN" type="INT32">
      <short_desc>Enable persistent onboard mission storage</short_desc>
Don Gagne's avatar
Don Gagne committed
1154
      <long_desc>When enabled, missions that have been uploaded by the GCS are stored and reloaded after reboot persistently.</long_desc>
1155 1156 1157
      <min>0</min>
      <max>1</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1158
    <parameter default="900" name="MIS_DIST_1WP" type="FLOAT">
1159
      <short_desc>Maximal horizontal distance from home to first waypoint</short_desc>
Don Gagne's avatar
Don Gagne committed
1160
      <long_desc>Failsafe check to prevent running mission stored from previous flight at a new takeoff location. Set a value of zero or less to disable. The mission will not be started if the current waypoint is more distant than MIS_DIS_1WP from the current position.</long_desc>
1161 1162 1163
      <min>0</min>
      <max>1000</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1164
    <parameter default="1" name="MIS_ALTMODE" type="INT32">
1165
      <short_desc>Altitude setpoint mode</short_desc>
Don Gagne's avatar
Don Gagne committed
1166
      <long_desc>0: the system will follow a zero order hold altitude setpoint 1: the system will follow a first order hold altitude setpoint values follow the definition in enum mission_altitude_mode</long_desc>
1167 1168 1169 1170 1171
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="1" name="MIS_YAWMODE" type="INT32">
      <short_desc>Multirotor only. Yaw setpoint mode</short_desc>
Don Gagne's avatar
Don Gagne committed
1172
      <long_desc>0: Set the yaw heading to the yaw value specified for the destination waypoint. 1: Maintain a yaw heading pointing towards the next waypoint. 2: Maintain a yaw heading that always points to the home location. 3: Maintain a yaw heading that always points away from the home location (ie: back always faces home). The values are defined in the enum mission_altitude_mode</long_desc>
1173 1174 1175
      <min>0</min>
      <max>3</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1176 1177 1178 1179 1180 1181
    <parameter default="50.0" name="NAV_LOITER_RAD" type="FLOAT">
      <short_desc>Loiter radius (FW only)</short_desc>
      <long_desc>Default value of loiter radius for missions, loiter, RTL, etc. (fixedwing only).</long_desc>
      <min>25</min>
      <max>1000</max>
      <unit>meter</unit>
1182
    </parameter>
Don Gagne's avatar
Don Gagne committed
1183 1184 1185 1186 1187 1188
    <parameter default="10.0" name="NAV_ACC_RAD" type="FLOAT">
      <short_desc>Acceptance Radius</short_desc>
      <long_desc>Default acceptance radius, overridden by acceptance radius of waypoint if set.</long_desc>
      <min>0.05</min>
      <max>200.0</max>
      <unit>meter</unit>
1189
    </parameter>
Don Gagne's avatar
Don Gagne committed
1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200
    <parameter default="0" name="NAV_DLL_OBC" type="INT32">
      <short_desc>Set OBC mode for data link loss</short_desc>
      <long_desc>If set to 1 the behaviour on data link loss is set to a mode according to the OBC rules</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="NAV_RCL_OBC" type="INT32">
      <short_desc>Set OBC mode for rc loss</short_desc>
      <long_desc>If set to 1 the behaviour on data link loss is set to a mode according to the OBC rules</long_desc>
      <min>0</min>
      <max>1</max>
1201
    </parameter>
Don Gagne's avatar
Don Gagne committed
1202 1203 1204
  </group>
  <group name="Multicopter Attitude Control">
    <parameter default="6.5" name="MC_ROLL_P" type="FLOAT">
1205 1206 1207 1208
      <short_desc>Roll P gain</short_desc>
      <long_desc>Roll proportional gain, i.e. desired angular speed in rad/s for error 1 rad.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1209
    <parameter default="0.15" name="MC_ROLLRATE_P" type="FLOAT">
1210 1211 1212 1213
      <short_desc>Roll rate P gain</short_desc>
      <long_desc>Roll rate proportional gain, i.e. control output for angular speed error 1 rad/s.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1214
    <parameter default="0.05" name="MC_ROLLRATE_I" type="FLOAT">
1215 1216 1217 1218
      <short_desc>Roll rate I gain</short_desc>
      <long_desc>Roll rate integral gain. Can be set to compensate static thrust difference or gravity center offset.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1219
    <parameter default="0.003" name="MC_ROLLRATE_D" type="FLOAT">
1220 1221 1222 1223
      <short_desc>Roll rate D gain</short_desc>
      <long_desc>Roll rate differential gain. Small values help reduce fast oscillations. If value is too big oscillations will appear again.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1224 1225 1226 1227 1228 1229
    <parameter default="0.0" name="MC_ROLLRATE_FF" type="FLOAT">
      <short_desc>Roll rate feedforward</short_desc>
      <long_desc>Improves tracking performance.</long_desc>
      <min>0.0</min>
    </parameter>
    <parameter default="6.5" name="MC_PITCH_P" type="FLOAT">
1230 1231 1232 1233 1234
      <short_desc>Pitch P gain</short_desc>
      <long_desc>Pitch proportional gain, i.e. desired angular speed in rad/s for error 1 rad.</long_desc>
      <min>0.0</min>
      <unit>1/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1235
    <parameter default="0.15" name="MC_PITCHRATE_P" type="FLOAT">
1236 1237 1238 1239
      <short_desc>Pitch rate P gain</short_desc>
      <long_desc>Pitch rate proportional gain, i.e. control output for angular speed error 1 rad/s.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1240
    <parameter default="0.05" name="MC_PITCHRATE_I" type="FLOAT">
1241 1242 1243 1244
      <short_desc>Pitch rate I gain</short_desc>
      <long_desc>Pitch rate integral gain. Can be set to compensate static thrust difference or gravity center offset.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1245
    <parameter default="0.003" name="MC_PITCHRATE_D" type="FLOAT">
1246 1247 1248 1249
      <short_desc>Pitch rate D gain</short_desc>
      <long_desc>Pitch rate differential gain. Small values help reduce fast oscillations. If value is too big oscillations will appear again.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1250 1251 1252 1253 1254 1255
    <parameter default="0.0" name="MC_PITCHRATE_FF" type="FLOAT">
      <short_desc>Pitch rate feedforward</short_desc>
      <long_desc>Improves tracking performance.</long_desc>
      <min>0.0</min>
    </parameter>
    <parameter default="2.8" name="MC_YAW_P" type="FLOAT">
1256 1257 1258 1259 1260
      <short_desc>Yaw P gain</short_desc>
      <long_desc>Yaw proportional gain, i.e. desired angular speed in rad/s for error 1 rad.</long_desc>
      <min>0.0</min>
      <unit>1/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1261
    <parameter default="0.2" name="MC_YAWRATE_P" type="FLOAT">
1262 1263 1264 1265
      <short_desc>Yaw rate P gain</short_desc>
      <long_desc>Yaw rate proportional gain, i.e. control output for angular speed error 1 rad/s.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1266
    <parameter default="0.1" name="MC_YAWRATE_I" type="FLOAT">
1267 1268 1269 1270
      <short_desc>Yaw rate I gain</short_desc>
      <long_desc>Yaw rate integral gain. Can be set to compensate static thrust difference or gravity center offset.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1271
    <parameter default="0.0" name="MC_YAWRATE_D" type="FLOAT">
1272 1273 1274 1275
      <short_desc>Yaw rate D gain</short_desc>
      <long_desc>Yaw rate differential gain. Small values help reduce fast oscillations. If value is too big oscillations will appear again.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1276 1277 1278 1279 1280 1281 1282 1283 1284
    <parameter default="0.0" name="MC_YAWRATE_FF" type="FLOAT">
      <short_desc>Yaw rate feedforward</short_desc>
      <long_desc>Improves tracking performance.</long_desc>
      <min>0.0</min>
    </parameter>
    <parameter default="0.5" name="MC_YAW_FF" type="FLOAT">
      <short_desc>Yaw feed forward</short_desc>
      <long_desc>Feed forward weight for manual yaw control. 0 will give slow responce and no overshot, 1 - fast responce and big overshot.</long_desc>
      <min>0.0</min>
1285 1286
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1287 1288 1289 1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301
    <parameter default="220.0" name="MC_ROLLRATE_MAX" type="FLOAT">
      <short_desc>Max roll rate</short_desc>
      <long_desc>Limit for roll rate, has effect for large rotations in autonomous mode, to avoid large control output and mixer saturation.</long_desc>
      <min>0.0</min>
      <max>360.0</max>
      <unit>deg/s</unit>
    </parameter>
    <parameter default="220.0" name="MC_PITCHRATE_MAX" type="FLOAT">
      <short_desc>Max pitch rate</short_desc>
      <long_desc>Limit for pitch rate, has effect for large rotations in autonomous mode, to avoid large control output and mixer saturation.</long_desc>
      <min>0.0</min>
      <max>360.0</max>
      <unit>deg/s</unit>
    </parameter>
    <parameter default="60.0" name="MC_YAWRATE_MAX" type="FLOAT">
1302
      <short_desc>Max yaw rate</short_desc>
Don Gagne's avatar
Don Gagne committed
1303
      <long_desc>Limit for yaw rate, has effect for large rotations in autonomous mode, to avoid large control output and mixer saturation. A value of significantly over 60 degrees per second can already lead to mixer saturation.</long_desc>
1304 1305 1306 1307
      <min>0.0</min>
      <max>360.0</max>
      <unit>deg/s</unit>
    </parameter>
1308
    <parameter default="360.0" name="MC_ACRO_R_MAX" type="FLOAT">
1309 1310 1311 1312 1313
      <short_desc>Max acro roll rate</short_desc>
      <min>0.0</min>
      <max>360.0</max>
      <unit>deg/s</unit>
    </parameter>
1314
    <parameter default="360.0" name="MC_ACRO_P_MAX" type="FLOAT">
1315 1316 1317 1318 1319
      <short_desc>Max acro pitch rate</short_desc>
      <min>0.0</min>
      <max>360.0</max>
      <unit>deg/s</unit>
    </parameter>
1320
    <parameter default="360.0" name="MC_ACRO_Y_MAX" type="FLOAT">
1321 1322 1323 1324
      <short_desc>Max acro yaw rate</short_desc>
      <min>0.0</min>
      <unit>deg/s</unit>
    </parameter>
1325 1326 1327 1328 1329 1330 1331
    <parameter default="1.0" name="MC_RATT_TH" type="FLOAT">
      <short_desc>Threshold for Rattitude mode</short_desc>
      <long_desc>Manual input needed in order to override attitude control rate setpoints and instead pass manual stick inputs as rate setpoints</long_desc>
      <min>0.0</min>
      <max>1.0</max>
      <unit />
    </parameter>
Don Gagne's avatar
Don Gagne committed
1332
    <parameter default="6.0" name="MP_ROLL_P" type="FLOAT">
1333 1334 1335 1336
      <short_desc>Roll P gain</short_desc>
      <long_desc>Roll proportional gain, i.e. desired angular speed in rad/s for error 1 rad.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1337
    <parameter default="0.1" name="MP_ROLLRATE_P" type="FLOAT">
1338 1339 1340 1341
      <short_desc>Roll rate P gain</short_desc>
      <long_desc>Roll rate proportional gain, i.e. control output for angular speed error 1 rad/s.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1342
    <parameter default="0.0" name="MP_ROLLRATE_I" type="FLOAT">
1343 1344 1345 1346
      <short_desc>Roll rate I gain</short_desc>
      <long_desc>Roll rate integral gain. Can be set to compensate static thrust difference or gravity center offset.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1347
    <parameter default="0.002" name="MP_ROLLRATE_D" type="FLOAT">
1348 1349 1350 1351
      <short_desc>Roll rate D gain</short_desc>
      <long_desc>Roll rate differential gain. Small values help reduce fast oscillations. If value is too big oscillations will appear again.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1352
    <parameter default="6.0" name="MP_PITCH_P" type="FLOAT">
1353 1354 1355 1356 1357
      <short_desc>Pitch P gain</short_desc>
      <long_desc>Pitch proportional gain, i.e. desired angular speed in rad/s for error 1 rad.</long_desc>
      <min>0.0</min>
      <unit>1/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1358
    <parameter default="0.1" name="MP_PITCHRATE_P" type="FLOAT">
1359 1360 1361 1362
      <short_desc>Pitch rate P gain</short_desc>
      <long_desc>Pitch rate proportional gain, i.e. control output for angular speed error 1 rad/s.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1363
    <parameter default="0.0" name="MP_PITCHRATE_I" type="FLOAT">
1364 1365 1366 1367
      <short_desc>Pitch rate I gain</short_desc>
      <long_desc>Pitch rate integral gain. Can be set to compensate static thrust difference or gravity center offset.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1368
    <parameter default="0.002" name="MP_PITCHRATE_D" type="FLOAT">
1369 1370 1371 1372
      <short_desc>Pitch rate D gain</short_desc>
      <long_desc>Pitch rate differential gain. Small values help reduce fast oscillations. If value is too big oscillations will appear again.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1373
    <parameter default="2.0" name="MP_YAW_P" type="FLOAT">
1374 1375 1376 1377 1378
      <short_desc>Yaw P gain</short_desc>
      <long_desc>Yaw proportional gain, i.e. desired angular speed in rad/s for error 1 rad.</long_desc>
      <min>0.0</min>
      <unit>1/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1379
    <parameter default="0.3" name="MP_YAWRATE_P" type="FLOAT">
1380 1381 1382 1383
      <short_desc>Yaw rate P gain</short_desc>
      <long_desc>Yaw rate proportional gain, i.e. control output for angular speed error 1 rad/s.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1384
    <parameter default="0.0" name="MP_YAWRATE_I" type="FLOAT">
1385 1386 1387 1388
      <short_desc>Yaw rate I gain</short_desc>
      <long_desc>Yaw rate integral gain. Can be set to compensate static thrust difference or gravity center offset.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1389
    <parameter default="0.0" name="MP_YAWRATE_D" type="FLOAT">
1390 1391 1392 1393
      <short_desc>Yaw rate D gain</short_desc>
      <long_desc>Yaw rate differential gain. Small values help reduce fast oscillations. If value is too big oscillations will appear again.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1394
    <parameter default="0.5" name="MP_YAW_FF" type="FLOAT">
1395 1396 1397 1398 1399
      <short_desc>Yaw feed forward</short_desc>
      <long_desc>Feed forward weight for manual yaw control. 0 will give slow responce and no overshot, 1 - fast responce and big overshot.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1400
    <parameter default="60.0" name="MP_YAWRATE_MAX" type="FLOAT">
1401 1402 1403 1404 1405 1406
      <short_desc>Max yaw rate</short_desc>
      <long_desc>Limit for yaw rate, has effect for large rotations in autonomous mode, to avoid large control output and mixer saturation.</long_desc>
      <min>0.0</min>
      <max>360.0</max>
      <unit>deg/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1407
    <parameter default="35.0" name="MP_ACRO_R_MAX" type="FLOAT">
1408 1409 1410 1411 1412
      <short_desc>Max acro roll rate</short_desc>
      <min>0.0</min>
      <max>360.0</max>
      <unit>deg/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1413
    <parameter default="35.0" name="MP_ACRO_P_MAX" type="FLOAT">
1414 1415 1416 1417 1418
      <short_desc>Max acro pitch rate</short_desc>
      <min>0.0</min>
      <max>360.0</max>
      <unit>deg/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1419
    <parameter default="120.0" name="MP_ACRO_Y_MAX" type="FLOAT">
1420 1421 1422 1423
      <short_desc>Max acro yaw rate</short_desc>
      <min>0.0</min>
      <unit>deg/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440
    <parameter default="35.0" name="MPP_MAN_R_MAX" type="FLOAT">
      <short_desc>Max manual roll</short_desc>
      <min>0.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="35.0" name="MPP_MAN_P_MAX" type="FLOAT">
      <short_desc>Max manual pitch</short_desc>
      <min>0.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="120.0" name="MPP_MAN_Y_MAX" type="FLOAT">
      <short_desc>Max manual yaw rate</short_desc>
      <min>0.0</min>
      <unit>deg/s</unit>
    </parameter>
1441 1442
  </group>
  <group name="Multicopter Position Control">
Don Gagne's avatar
Don Gagne committed
1443 1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456
    <parameter default="0.12" name="MPC_THR_MIN" type="FLOAT">
      <short_desc>Minimum thrust in auto thrust control</short_desc>
      <long_desc>It's recommended to set it &gt; 0 to avoid free fall with zero thrust.</long_desc>
      <min>0.05</min>
      <max>1.0</max>
    </parameter>
    <parameter default="0.9" name="MPC_THR_MAX" type="FLOAT">
      <short_desc>Maximum thrust in auto thrust control</short_desc>
      <long_desc>Limit max allowed thrust. Setting a value of one can put the system into actuator saturation as no spread between the motors is possible any more. A value of 0.8 - 0.9 is recommended.</long_desc>
      <min>0.0</min>
      <max>0.95</max>
    </parameter>
    <parameter default="0.12" name="MPC_MANTHR_MIN" type="FLOAT">
      <short_desc>Minimum manual thrust</short_desc>
1457 1458 1459 1460
      <long_desc>Minimum vertical thrust. It's recommended to set it &gt; 0 to avoid free fall with zero thrust.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1461 1462 1463
    <parameter default="0.9" name="MPC_MANTHR_MAX" type="FLOAT">
      <short_desc>Maximum manual thrust</short_desc>
      <long_desc>Limit max allowed thrust. Setting a value of one can put the system into actuator saturation as no spread between the motors is possible any more. A value of 0.8 - 0.9 is recommended.</long_desc>
1464 1465 1466
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1467
    <parameter default="1.0" name="MPC_Z_P" type="FLOAT">
1468 1469 1470
      <short_desc>Proportional gain for vertical position error</short_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1471
    <parameter default="0.2" name="MPC_Z_VEL_P" type="FLOAT">
1472 1473 1474
      <short_desc>Proportional gain for vertical velocity error</short_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1475
    <parameter default="0.02" name="MPC_Z_VEL_I" type="FLOAT">
1476 1477 1478 1479
      <short_desc>Integral gain for vertical velocity error</short_desc>
      <long_desc>Non zero value allows hovering thrust estimation on stabilized or autonomous takeoff.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1480
    <parameter default="0.0" name="MPC_Z_VEL_D" type="FLOAT">
1481 1482 1483
      <short_desc>Differential gain for vertical velocity error</short_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1484
    <parameter default="3.0" name="MPC_Z_VEL_MAX" type="FLOAT">
1485
      <short_desc>Maximum vertical velocity</short_desc>
Don Gagne's avatar
Don Gagne committed
1486
      <long_desc>Maximum vertical velocity in AUTO mode and endpoint for stabilized modes (ALTCTRL, POSCTRL).</long_desc>
1487
      <min>0.0</min>
Don Gagne's avatar
Don Gagne committed
1488
      <max>8.0</max>
1489 1490
      <unit>m/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1491
    <parameter default="0.5" name="MPC_Z_FF" type="FLOAT">
1492
      <short_desc>Vertical velocity feed forward</short_desc>
Don Gagne's avatar
Don Gagne committed
1493
      <long_desc>Feed forward weight for altitude control in stabilized modes (ALTCTRL, POSCTRL). 0 will give slow responce and no overshot, 1 - fast responce and big overshot.</long_desc>
1494 1495 1496
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1497
    <parameter default="1.0" name="MPC_XY_P" type="FLOAT">
1498 1499 1500
      <short_desc>Proportional gain for horizontal position error</short_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1501
    <parameter default="0.1" name="MPC_XY_VEL_P" type="FLOAT">
1502 1503 1504
      <short_desc>Proportional gain for horizontal velocity error</short_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1505
    <parameter default="0.02" name="MPC_XY_VEL_I" type="FLOAT">
1506 1507 1508 1509
      <short_desc>Integral gain for horizontal velocity error</short_desc>
      <long_desc>Non-zero value allows to resist wind.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1510
    <parameter default="0.01" name="MPC_XY_VEL_D" type="FLOAT">
1511 1512 1513
      <short_desc>Differential gain for horizontal velocity error. Small values help reduce fast oscillations. If value is too big oscillations will appear again</short_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1514
    <parameter default="5.0" name="MPC_XY_VEL_MAX" type="FLOAT">
1515 1516 1517 1518 1519
      <short_desc>Maximum horizontal velocity</short_desc>
      <long_desc>Maximum horizontal velocity in AUTO mode and endpoint for position stabilized mode (POSCTRL).</long_desc>
      <min>0.0</min>
      <unit>m/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1520
    <parameter default="0.5" name="MPC_XY_FF" type="FLOAT">
1521 1522 1523 1524 1525
      <short_desc>Horizontal velocity feed forward</short_desc>
      <long_desc>Feed forward weight for position control in position control mode (POSCTRL). 0 will give slow responce and no overshot, 1 - fast responce and big overshot.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1526
    <parameter default="45.0" name="MPC_TILTMAX_AIR" type="FLOAT">
1527 1528 1529 1530
      <short_desc>Maximum tilt angle in air</short_desc>
      <long_desc>Limits maximum tilt in AUTO and POSCTRL modes during flight.</long_desc>
      <min>0.0</min>
      <max>90.0</max>
Don Gagne's avatar
Don Gagne committed
1531
      <unit>degree</unit>
1532
    </parameter>
Don Gagne's avatar
Don Gagne committed
1533
    <parameter default="15.0" name="MPC_TILTMAX_LND" type="FLOAT">
1534 1535 1536 1537
      <short_desc>Maximum tilt during landing</short_desc>
      <long_desc>Limits maximum tilt angle on landing.</long_desc>
      <min>0.0</min>
      <max>90.0</max>
Don Gagne's avatar
Don Gagne committed
1538
      <unit>degree</unit>
1539
    </parameter>
Don Gagne's avatar
Don Gagne committed
1540
    <parameter default="1.0" name="MPC_LAND_SPEED" type="FLOAT">
1541 1542 1543 1544
      <short_desc>Landing descend rate</short_desc>
      <min>0.0</min>
      <unit>m/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561
    <parameter default="35.0" name="MPC_MAN_R_MAX" type="FLOAT">
      <short_desc>Max manual roll</short_desc>
      <min>0.0</min>
      <max>90.0</max>
      <unit>degree</unit>
    </parameter>
    <parameter default="35.0" name="MPC_MAN_P_MAX" type="FLOAT">
      <short_desc>Max manual pitch</short_desc>
      <min>0.0</min>
      <max>90.0</max>
      <unit>degree</unit>
    </parameter>
    <parameter default="120.0" name="MPC_MAN_Y_MAX" type="FLOAT">
      <short_desc>Max manual yaw rate</short_desc>
      <min>0.0</min>
      <unit>degree / s</unit>
    </parameter>
1562 1563 1564 1565 1566 1567 1568 1569 1570 1571 1572 1573 1574 1575 1576 1577 1578 1579 1580 1581 1582 1583 1584 1585 1586 1587 1588
    <parameter default="0.1" name="MPC_HOLD_XY_DZ" type="FLOAT">
      <short_desc>Deadzone of X,Y sticks where position hold is enabled</short_desc>
      <min>0.0</min>
      <max>1.0</max>
      <unit>%</unit>
    </parameter>
    <parameter default="0.1" name="MPC_HOLD_Z_DZ" type="FLOAT">
      <short_desc>Deadzone of Z stick where altitude hold is enabled</short_desc>
      <min>0.0</min>
      <max>1.0</max>
      <unit>%</unit>
    </parameter>
    <parameter default="0.5" name="MPC_HOLD_MAX_XY" type="FLOAT">
      <short_desc>Maximum horizontal velocity for which position hold is enabled (use 0 to disable check)</short_desc>
      <min>0.0</min>
      <unit>m/s</unit>
    </parameter>
    <parameter default="0.5" name="MPC_HOLD_MAX_Z" type="FLOAT">
      <short_desc>Maximum vertical velocity for which position hold is enabled (use 0 to disable check)</short_desc>
      <min>0.0</min>
      <unit>m/s</unit>
    </parameter>
    <parameter default="5.0" name="MPC_VELD_LP" type="FLOAT">
      <short_desc>Low pass filter cut freq. for numerical velocity derivative</short_desc>
      <min>0.0</min>
      <unit>Hz</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1589
    <parameter default="0.1" name="MPP_THR_MIN" type="FLOAT">
1590 1591 1592 1593 1594
      <short_desc>Minimum thrust</short_desc>
      <long_desc>Minimum vertical thrust. It's recommended to set it &gt; 0 to avoid free fall with zero thrust.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1595
    <parameter default="1.0" name="MPP_THR_MAX" type="FLOAT">
1596 1597 1598 1599 1600
      <short_desc>Maximum thrust</short_desc>
      <long_desc>Limit max allowed thrust.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1601
    <parameter default="1.0" name="MPP_Z_P" type="FLOAT">
1602 1603 1604
      <short_desc>Proportional gain for vertical position error</short_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1605
    <parameter default="0.1" name="MPP_Z_VEL_P" type="FLOAT">
1606 1607 1608
      <short_desc>Proportional gain for vertical velocity error</short_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1609
    <parameter default="0.02" name="MPP_Z_VEL_I" type="FLOAT">
1610 1611 1612 1613
      <short_desc>Integral gain for vertical velocity error</short_desc>
      <long_desc>Non zero value allows hovering thrust estimation on stabilized or autonomous takeoff.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1614
    <parameter default="0.0" name="MPP_Z_VEL_D" type="FLOAT">
1615 1616 1617
      <short_desc>Differential gain for vertical velocity error</short_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1618
    <parameter default="5.0" name="MPP_Z_VEL_MAX" type="FLOAT">
1619
      <short_desc>Maximum vertical velocity</short_desc>
Don Gagne's avatar
Don Gagne committed
1620
      <long_desc>Maximum vertical velocity in AUTO mode and endpoint for stabilized modes (ALTCTRL).</long_desc>
1621 1622 1623
      <min>0.0</min>
      <unit>m/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1624
    <parameter default="0.5" name="MPP_Z_FF" type="FLOAT">
1625
      <short_desc>Vertical velocity feed forward</short_desc>
Don Gagne's avatar
Don Gagne committed
1626
      <long_desc>Feed forward weight for altitude control in stabilized modes (ALTCTRL). 0 will give slow responce and no overshot, 1 - fast responce and big overshot.</long_desc>
1627 1628 1629
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1630
    <parameter default="1.0" name="MPP_XY_P" type="FLOAT">
1631 1632 1633
      <short_desc>Proportional gain for horizontal position error</short_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1634
    <parameter default="0.1" name="MPP_XY_VEL_P" type="FLOAT">
1635 1636 1637
      <short_desc>Proportional gain for horizontal velocity error</short_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1638
    <parameter default="0.02" name="MPP_XY_VEL_I" type="FLOAT">
1639 1640 1641 1642
      <short_desc>Integral gain for horizontal velocity error</short_desc>
      <long_desc>Non-zero value allows to resist wind.</long_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1643
    <parameter default="0.01" name="MPP_XY_VEL_D" type="FLOAT">
1644 1645 1646
      <short_desc>Differential gain for horizontal velocity error. Small values help reduce fast oscillations. If value is too big oscillations will appear again</short_desc>
      <min>0.0</min>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1647
    <parameter default="5.0" name="MPP_XY_VEL_MAX" type="FLOAT">
1648 1649 1650 1651 1652
      <short_desc>Maximum horizontal velocity</short_desc>
      <long_desc>Maximum horizontal velocity in AUTO mode and endpoint for position stabilized mode (POSCTRL).</long_desc>
      <min>0.0</min>
      <unit>m/s</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1653
    <parameter default="0.5" name="MPP_XY_FF" type="FLOAT">
1654 1655 1656 1657 1658
      <short_desc>Horizontal velocity feed forward</short_desc>
      <long_desc>Feed forward weight for position control in position control mode (POSCTRL). 0 will give slow responce and no overshot, 1 - fast responce and big overshot.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1659
    <parameter default="45.0" name="MPP_TILTMAX_AIR" type="FLOAT">
1660 1661 1662 1663 1664 1665
      <short_desc>Maximum tilt angle in air</short_desc>
      <long_desc>Limits maximum tilt in AUTO and POSCTRL modes during flight.</long_desc>
      <min>0.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1666
    <parameter default="15.0" name="MPP_TILTMAX_LND" type="FLOAT">
1667 1668 1669 1670 1671 1672
      <short_desc>Maximum tilt during landing</short_desc>
      <long_desc>Limits maximum tilt angle on landing.</long_desc>
      <min>0.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1673
    <parameter default="1.0" name="MPP_LAND_SPEED" type="FLOAT">
1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686 1687 1688 1689 1690 1691 1692 1693 1694 1695 1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 1739 1740 1741 1742 1743 1744 1745 1746 1747 1748 1749 1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760 1761 1762 1763
      <short_desc>Landing descend rate</short_desc>
      <min>0.0</min>
      <unit>m/s</unit>
    </parameter>
  </group>
  <group name="PWM Outputs">
    <parameter default="0" name="PWM_AUX_REV1" type="INT32">
      <short_desc>Invert direction of aux output channel 1</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_AUX_REV2" type="INT32">
      <short_desc>Invert direction of aux output channel 2</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_AUX_REV3" type="INT32">
      <short_desc>Invert direction of aux output channel 3</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_AUX_REV4" type="INT32">
      <short_desc>Invert direction of aux output channel 4</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_AUX_REV5" type="INT32">
      <short_desc>Invert direction of aux output channel 5</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_AUX_REV6" type="INT32">
      <short_desc>Invert direction of aux output channel 6</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_MAIN_REV1" type="INT32">
      <short_desc>Invert direction of main output channel 1</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_MAIN_REV2" type="INT32">
      <short_desc>Invert direction of main output channel 2</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_MAIN_REV3" type="INT32">
      <short_desc>Invert direction of main output channel 3</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_MAIN_REV4" type="INT32">
      <short_desc>Invert direction of main output channel 4</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_MAIN_REV5" type="INT32">
      <short_desc>Invert direction of main output channel 5</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_MAIN_REV6" type="INT32">
      <short_desc>Invert direction of main output channel 6</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_MAIN_REV7" type="INT32">
      <short_desc>Invert direction of main output channel 7</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0" name="PWM_MAIN_REV8" type="INT32">
      <short_desc>Invert direction of main output channel 8</short_desc>
      <long_desc>Set to 1 to invert the channel, 0 for default direction.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1764 1765 1766 1767 1768 1769 1770 1771 1772 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782 1783 1784 1785 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797 1798 1799 1800 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811
    <parameter default="0" name="PWM_SBUS_MODE" type="INT32">
      <short_desc>Enable S.BUS out</short_desc>
      <long_desc>Set to 1 to enable S.BUS version 1 output instead of RSSI.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="1000" name="PWM_MIN" type="INT32">
      <short_desc>Set the minimum PWM for the MAIN outputs</short_desc>
      <long_desc>IMPORTANT: CHANGING THIS PARAMETER REQUIRES A COMPLETE SYSTEM REBOOT IN ORDER TO APPLY THE CHANGES. COMPLETELY POWER-CYCLE THE SYSTEM TO PUT CHANGES INTO EFFECT. Set to 1000 for industry default or 900 to increase servo travel.</long_desc>
      <min>800</min>
      <max>1400</max>
      <unit>microseconds</unit>
    </parameter>
    <parameter default="2000" name="PWM_MAX" type="INT32">
      <short_desc>Set the maximum PWM for the MAIN outputs</short_desc>
      <long_desc>IMPORTANT: CHANGING THIS PARAMETER REQUIRES A COMPLETE SYSTEM REBOOT IN ORDER TO APPLY THE CHANGES. COMPLETELY POWER-CYCLE THE SYSTEM TO PUT CHANGES INTO EFFECT. Set to 2000 for industry default or 2100 to increase servo travel.</long_desc>
      <min>1600</min>
      <max>2200</max>
      <unit>microseconds</unit>
    </parameter>
    <parameter default="0" name="PWM_DISARMED" type="INT32">
      <short_desc>Set the disarmed PWM for MAIN outputs</short_desc>
      <long_desc>IMPORTANT: CHANGING THIS PARAMETER REQUIRES A COMPLETE SYSTEM REBOOT IN ORDER TO APPLY THE CHANGES. COMPLETELY POWER-CYCLE THE SYSTEM TO PUT CHANGES INTO EFFECT. This is the PWM pulse the autopilot is outputting if not armed. The main use of this parameter is to silence ESCs when they are disarmed.</long_desc>
      <min>0</min>
      <max>2200</max>
      <unit>microseconds</unit>
    </parameter>
    <parameter default="1000" name="PWM_AUX_MIN" type="INT32">
      <short_desc>Set the minimum PWM for the MAIN outputs</short_desc>
      <long_desc>IMPORTANT: CHANGING THIS PARAMETER REQUIRES A COMPLETE SYSTEM REBOOT IN ORDER TO APPLY THE CHANGES. COMPLETELY POWER-CYCLE THE SYSTEM TO PUT CHANGES INTO EFFECT. Set to 1000 for default or 900 to increase servo travel</long_desc>
      <min>800</min>
      <max>1400</max>
      <unit>microseconds</unit>
    </parameter>
    <parameter default="2000" name="PWM_AUX_MAX" type="INT32">
      <short_desc>Set the maximum PWM for the MAIN outputs</short_desc>
      <long_desc>IMPORTANT: CHANGING THIS PARAMETER REQUIRES A COMPLETE SYSTEM REBOOT IN ORDER TO APPLY THE CHANGES. COMPLETELY POWER-CYCLE THE SYSTEM TO PUT CHANGES INTO EFFECT. Set to 2000 for default or 2100 to increase servo travel</long_desc>
      <min>1600</min>
      <max>2200</max>
      <unit>microseconds</unit>
    </parameter>
    <parameter default="1000" name="PWM_AUX_DISARMED" type="INT32">
      <short_desc>Set the disarmed PWM for AUX outputs</short_desc>
      <long_desc>IMPORTANT: CHANGING THIS PARAMETER REQUIRES A COMPLETE SYSTEM REBOOT IN ORDER TO APPLY THE CHANGES. COMPLETELY POWER-CYCLE THE SYSTEM TO PUT CHANGES INTO EFFECT. This is the PWM pulse the autopilot is outputting if not armed. The main use of this parameter is to silence ESCs when they are disarmed.</long_desc>
      <min>0</min>
      <max>2200</max>
      <unit>microseconds</unit>
    </parameter>
1812 1813 1814 1815
  </group>
  <group name="Payload drop">
    <parameter default="0.03" name="BD_GPROPERTIES" type="FLOAT">
      <short_desc>Ground drag property</short_desc>
Don Gagne's avatar
Don Gagne committed
1816
      <long_desc>This parameter encodes the ground drag coefficient and the corresponding decrease in wind speed from the plane altitude to ground altitude.</long_desc>
1817 1818 1819 1820 1821 1822
      <min>0.001</min>
      <max>0.1</max>
      <unit>unknown</unit>
    </parameter>
    <parameter default="120.0" name="BD_TURNRADIUS" type="FLOAT">
      <short_desc>Plane turn radius</short_desc>
Don Gagne's avatar
Don Gagne committed
1823
      <long_desc>The planes known minimal turn radius - use a higher value to make the plane maneuver more distant from the actual drop position. This is to ensure the wings are level during the drop.</long_desc>
1824 1825 1826 1827 1828 1829
      <min>30.0</min>
      <max>500.0</max>
      <unit>meter</unit>
    </parameter>
    <parameter default="30.0" name="BD_PRECISION" type="FLOAT">
      <short_desc>Drop precision</short_desc>
Don Gagne's avatar
Don Gagne committed
1830
      <long_desc>If the system is closer than this distance on passing over the drop position, it will release the payload. This is a safeguard to prevent a drop out of the required accuracy.</long_desc>
1831 1832 1833 1834 1835 1836
      <min>1.0</min>
      <max>80.0</max>
      <unit>meter</unit>
    </parameter>
    <parameter default="0.1" name="BD_OBJ_CD" type="FLOAT">
      <short_desc>Payload drag coefficient of the dropped object</short_desc>
Don Gagne's avatar
Don Gagne committed
1837
      <long_desc>The drag coefficient (cd) is the typical drag constant for air. It is in general object specific, but the closest primitive shape to the actual object should give good results: http://en.wikipedia.org/wiki/Drag_coefficient</long_desc>
1838 1839 1840 1841 1842 1843
      <min>0.08</min>
      <max>1.5</max>
      <unit>meter</unit>
    </parameter>
    <parameter default="0.6" name="BD_OBJ_MASS" type="FLOAT">
      <short_desc>Payload mass</short_desc>
Don Gagne's avatar
Don Gagne committed
1844
      <long_desc>A typical small toy ball: 0.025 kg OBC water bottle: 0.6 kg</long_desc>
1845 1846 1847 1848 1849 1850
      <min>0.001</min>
      <max>5.0</max>
      <unit>kilogram</unit>
    </parameter>
    <parameter default="0.00311724531" name="BD_OBJ_SURFACE" type="FLOAT">
      <short_desc>Payload front surface area</short_desc>
Don Gagne's avatar
Don Gagne committed
1851
      <long_desc>A typical small toy ball: (0.045 * 0.045) / 4.0 * pi = 0.001590 m^2 OBC water bottle: (0.063 * 0.063) / 4.0 * pi = 0.003117 m^2</long_desc>
1852 1853 1854 1855 1856 1857 1858 1859 1860 1861 1862 1863 1864 1865 1866 1867 1868 1869 1870 1871 1872 1873 1874 1875 1876 1877
      <min>0.001</min>
      <max>0.5</max>
      <unit>m^2</unit>
    </parameter>
  </group>
  <group name="Position Estimator">
    <parameter default="230" name="PE_VEL_DELAY_MS" type="INT32">
      <short_desc>Velocity estimate delay</short_desc>
      <long_desc>The delay in milliseconds of the velocity estimate from GPS.</long_desc>
      <min>0</min>
      <max>1000</max>
    </parameter>
    <parameter default="210" name="PE_POS_DELAY_MS" type="INT32">
      <short_desc>Position estimate delay</short_desc>
      <long_desc>The delay in milliseconds of the position estimate from GPS.</long_desc>
      <min>0</min>
      <max>1000</max>
    </parameter>
    <parameter default="350" name="PE_HGT_DELAY_MS" type="INT32">
      <short_desc>Height estimate delay</short_desc>
      <long_desc>The delay in milliseconds of the height estimate from the barometer.</long_desc>
      <min>0</min>
      <max>1000</max>
    </parameter>
    <parameter default="30" name="PE_MAG_DELAY_MS" type="INT32">
      <short_desc>Mag estimate delay</short_desc>
Don Gagne's avatar
Don Gagne committed
1878
      <long_desc>The delay in milliseconds of the magnetic field estimate from the magnetometer.</long_desc>
1879 1880 1881 1882 1883 1884 1885 1886 1887 1888 1889 1890 1891 1892 1893 1894 1895
      <min>0</min>
      <max>1000</max>
    </parameter>
    <parameter default="210" name="PE_TAS_DELAY_MS" type="INT32">
      <short_desc>True airspeeed estimate delay</short_desc>
      <long_desc>The delay in milliseconds of the airspeed estimate.</long_desc>
      <min>0</min>
      <max>1000</max>
    </parameter>
    <parameter default="0.9" name="PE_GPS_ALT_WGT" type="FLOAT">
      <short_desc>GPS vs. barometric altitude update weight</short_desc>
      <long_desc>RE-CHECK this.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="1.4" name="PE_EAS_NOISE" type="FLOAT">
      <short_desc>Airspeed measurement noise</short_desc>
Don Gagne's avatar
Don Gagne committed
1896
      <long_desc>Increasing this value will make the filter trust this sensor less and trust other sensors more.</long_desc>
1897 1898 1899 1900 1901 1902 1903 1904 1905
      <min>0.5</min>
      <max>5.0</max>
    </parameter>
    <parameter default="0.3" name="PE_VELNE_NOISE" type="FLOAT">
      <short_desc>Velocity measurement noise in north-east (horizontal) direction</short_desc>
      <long_desc>Generic default: 0.3, multicopters: 0.5, ground vehicles: 0.5</long_desc>
      <min>0.05</min>
      <max>5.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1906
    <parameter default="0.3" name="PE_VELD_NOISE" type="FLOAT">
1907
      <short_desc>Velocity noise in down (vertical) direction</short_desc>
Don Gagne's avatar
Don Gagne committed
1908 1909 1910
      <long_desc>Generic default: 0.3, multicopters: 0.4, ground vehicles: 0.7</long_desc>
      <min>0.2</min>
      <max>3.0</max>
1911 1912 1913 1914 1915 1916 1917
    </parameter>
    <parameter default="0.5" name="PE_POSNE_NOISE" type="FLOAT">
      <short_desc>Position noise in north-east (horizontal) direction</short_desc>
      <long_desc>Generic defaults: 0.5, multicopters: 0.5, ground vehicles: 0.5</long_desc>
      <min>0.1</min>
      <max>10.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1918
    <parameter default="1.25" name="PE_POSD_NOISE" type="FLOAT">
1919
      <short_desc>Position noise in down (vertical) direction</short_desc>
Don Gagne's avatar
Don Gagne committed
1920 1921 1922
      <long_desc>Generic defaults: 1.25, multicopters: 1.0, ground vehicles: 1.0</long_desc>
      <min>0.5</min>
      <max>3.0</max>
1923 1924 1925 1926
    </parameter>
    <parameter default="0.05" name="PE_MAG_NOISE" type="FLOAT">
      <short_desc>Magnetometer measurement noise</short_desc>
      <long_desc>Generic defaults: 0.05, multicopters: 0.05, ground vehicles: 0.05</long_desc>
Don Gagne's avatar
Don Gagne committed
1927 1928
      <min>0.01</min>
      <max>1.0</max>
1929 1930 1931
    </parameter>
    <parameter default="0.015" name="PE_GYRO_PNOISE" type="FLOAT">
      <short_desc>Gyro process noise</short_desc>
Don Gagne's avatar
Don Gagne committed
1932
      <long_desc>Generic defaults: 0.015, multicopters: 0.015, ground vehicles: 0.015. This noise controls how much the filter trusts the gyro measurements. Increasing it makes the filter trust the gyro less and other sensors more.</long_desc>
1933 1934 1935 1936 1937
      <min>0.001</min>
      <max>0.05</max>
    </parameter>
    <parameter default="0.25" name="PE_ACC_PNOISE" type="FLOAT">
      <short_desc>Accelerometer process noise</short_desc>
Don Gagne's avatar
Don Gagne committed
1938
      <long_desc>Generic defaults: 0.25, multicopters: 0.25, ground vehicles: 0.25. Increasing this value makes the filter trust the accelerometer less and other sensors more.</long_desc>
1939 1940 1941
      <min>0.05</min>
      <max>1.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1942
    <parameter default="1e-07" name="PE_GBIAS_PNOISE" type="FLOAT">
1943
      <short_desc>Gyro bias estimate process noise</short_desc>
Don Gagne's avatar
Don Gagne committed
1944 1945
      <long_desc>Generic defaults: 1e-07f, multicopters: 1e-07f, ground vehicles: 1e-07f. Increasing this value will make the gyro bias converge faster but noisier.</long_desc>
      <min>0.00000005</min>
1946 1947
      <max>0.00001</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1948
    <parameter default="1e-05" name="PE_ABIAS_PNOISE" type="FLOAT">
1949
      <short_desc>Accelerometer bias estimate process noise</short_desc>
Don Gagne's avatar
Don Gagne committed
1950
      <long_desc>Generic defaults: 0.00001f, multicopters: 0.00001f, ground vehicles: 0.00001f. Increasing this value makes the bias estimation faster and noisier.</long_desc>
1951 1952 1953 1954 1955
      <min>0.00001</min>
      <max>0.001</max>
    </parameter>
    <parameter default="0.0003" name="PE_MAGE_PNOISE" type="FLOAT">
      <short_desc>Magnetometer earth frame offsets process noise</short_desc>
Don Gagne's avatar
Don Gagne committed
1956
      <long_desc>Generic defaults: 0.0001, multicopters: 0.0001, ground vehicles: 0.0001. Increasing this value makes the magnetometer earth bias estimate converge faster but also noisier.</long_desc>
1957 1958 1959 1960 1961
      <min>0.0001</min>
      <max>0.01</max>
    </parameter>
    <parameter default="0.0003" name="PE_MAGB_PNOISE" type="FLOAT">
      <short_desc>Magnetometer body frame offsets process noise</short_desc>
Don Gagne's avatar
Don Gagne committed
1962
      <long_desc>Generic defaults: 0.0003, multicopters: 0.0003, ground vehicles: 0.0003. Increasing this value makes the magnetometer body bias estimate converge faster but also noisier.</long_desc>
1963 1964 1965
      <min>0.0001</min>
      <max>0.01</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
1966 1967 1968 1969 1970 1971 1972 1973 1974 1975 1976 1977 1978 1979 1980 1981 1982 1983
    <parameter default="0.0" name="PE_MAGB_X" type="FLOAT">
      <short_desc>Magnetometer X bias</short_desc>
      <long_desc>The magnetometer bias. This bias is learnt by the filter over time and persists between boots.</long_desc>
      <min>-0.6</min>
      <max>0.6</max>
    </parameter>
    <parameter default="0.0" name="PE_MAGB_Y" type="FLOAT">
      <short_desc>Magnetometer Y bias</short_desc>
      <long_desc>The magnetometer bias. This bias is learnt by the filter over time and persists between boots.</long_desc>
      <min>-0.6</min>
      <max>0.6</max>
    </parameter>
    <parameter default="0.0" name="PE_MAGB_Z" type="FLOAT">
      <short_desc>Magnetometer Z bias</short_desc>
      <long_desc>The magnetometer bias. This bias is learnt by the filter over time and persists between boots.</long_desc>
      <min>-0.6</min>
      <max>0.6</max>
    </parameter>
1984 1985
    <parameter default="5.0" name="PE_POSDEV_INIT" type="FLOAT">
      <short_desc>Threshold for filter initialization</short_desc>
Don Gagne's avatar
Don Gagne committed
1986
      <long_desc>If the standard deviation of the GPS position estimate is below this threshold in meters, the filter will initialize.</long_desc>
1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015
      <min>0.3</min>
      <max>10.0</max>
    </parameter>
  </group>
  <group name="Position Estimator INAV">
    <parameter default="0.5" name="INAV_W_Z_BARO" type="FLOAT">
      <short_desc>Z axis weight for barometer</short_desc>
      <long_desc>Weight (cutoff frequency) for barometer altitude measurements.</long_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.005" name="INAV_W_Z_GPS_P" type="FLOAT">
      <short_desc>Z axis weight for GPS</short_desc>
      <long_desc>Weight (cutoff frequency) for GPS altitude measurements. GPS altitude data is very noisy and should be used only as slow correction for baro offset.</long_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.0" name="INAV_W_Z_GPS_V" type="FLOAT">
      <short_desc>Z velocity weight for GPS</short_desc>
      <long_desc>Weight (cutoff frequency) for GPS altitude velocity measurements.</long_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="5.0" name="INAV_W_Z_VIS_P" type="FLOAT">
      <short_desc>Z axis weight for vision</short_desc>
      <long_desc>Weight (cutoff frequency) for vision altitude measurements. vision altitude data is very noisy and should be used only as slow correction for baro offset.</long_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
2016 2017 2018
    <parameter default="3.0" name="INAV_W_Z_LIDAR" type="FLOAT">
      <short_desc>Z axis weight for lidar</short_desc>
      <long_desc>Weight (cutoff frequency) for lidar measurements.</long_desc>
2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 2031 2032 2033 2034 2035 2036 2037 2038 2039 2040 2041 2042 2043 2044 2045
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="1.0" name="INAV_W_XY_GPS_P" type="FLOAT">
      <short_desc>XY axis weight for GPS position</short_desc>
      <long_desc>Weight (cutoff frequency) for GPS position measurements.</long_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="2.0" name="INAV_W_XY_GPS_V" type="FLOAT">
      <short_desc>XY axis weight for GPS velocity</short_desc>
      <long_desc>Weight (cutoff frequency) for GPS velocity measurements.</long_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="7.0" name="INAV_W_XY_VIS_P" type="FLOAT">
      <short_desc>XY axis weight for vision position</short_desc>
      <long_desc>Weight (cutoff frequency) for vision position measurements.</long_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.0" name="INAV_W_XY_VIS_V" type="FLOAT">
      <short_desc>XY axis weight for vision velocity</short_desc>
      <long_desc>Weight (cutoff frequency) for vision velocity measurements.</long_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
2046 2047 2048 2049 2050 2051
    <parameter default="10.0" name="INAV_W_MOC_P" type="FLOAT">
      <short_desc>Weight for mocap system</short_desc>
      <long_desc>Weight (cutoff frequency) for mocap position measurements.</long_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
2052
    <parameter default="10.0" name="INAV_W_XY_FLOW" type="FLOAT">
2053 2054 2055
      <short_desc>XY axis weight for optical flow</short_desc>
      <long_desc>Weight (cutoff frequency) for optical flow (velocity) measurements.</long_desc>
      <min>0.0</min>
2056
      <max>30.0</max>
2057 2058 2059 2060 2061 2062 2063 2064 2065 2066 2067 2068 2069 2070 2071 2072 2073 2074 2075 2076 2077 2078 2079 2080 2081 2082
    </parameter>
    <parameter default="0.5" name="INAV_W_XY_RES_V" type="FLOAT">
      <short_desc>XY axis weight for resetting velocity</short_desc>
      <long_desc>When velocity sources lost slowly decrease estimated horizontal velocity with this weight.</long_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.1" name="INAV_W_GPS_FLOW" type="FLOAT">
      <short_desc>XY axis weight factor for GPS when optical flow available</short_desc>
      <long_desc>When optical flow data available, multiply GPS weights (for position and velocity) by this factor.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="0.05" name="INAV_W_ACC_BIAS" type="FLOAT">
      <short_desc>Accelerometer bias estimation weight</short_desc>
      <long_desc>Weight (cutoff frequency) for accelerometer bias estimation. 0 to disable.</long_desc>
      <min>0.0</min>
      <max>0.1</max>
    </parameter>
    <parameter default="0.15" name="INAV_FLOW_K" type="FLOAT">
      <short_desc>Optical flow scale factor</short_desc>
      <long_desc>Factor to convert raw optical flow (in pixels) to radians [rad/px].</long_desc>
      <min>0.0</min>
      <max>1.0</max>
      <unit>rad/px</unit>
    </parameter>
2083
    <parameter default="0.3" name="INAV_FLOW_Q_MIN" type="FLOAT">
2084 2085 2086 2087 2088
      <short_desc>Minimal acceptable optical flow quality</short_desc>
      <long_desc>0 - lowest quality, 1 - best quality.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
2089 2090 2091
    <parameter default="0.05" name="INAV_LIDAR_FILT" type="FLOAT">
      <short_desc>Weight for lidar filter</short_desc>
      <long_desc>Lidar filter detects spikes on lidar measurements and used to detect new surface level.</long_desc>
2092 2093 2094
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
2095
    <parameter default="0.5" name="INAV_LIDAR_ERR" type="FLOAT">
2096 2097 2098 2099 2100 2101 2102 2103 2104 2105 2106 2107 2108 2109 2110 2111 2112 2113 2114 2115 2116 2117 2118 2119 2120 2121 2122 2123 2124 2125 2126 2127 2128
      <short_desc>Sonar maximal error for new surface</short_desc>
      <long_desc>If sonar measurement error is larger than this value it skiped (spike) or accepted as new surface level (if offset is stable).</long_desc>
      <min>0.0</min>
      <max>1.0</max>
      <unit>m</unit>
    </parameter>
    <parameter default="3.0" name="INAV_LAND_T" type="FLOAT">
      <short_desc>Land detector time</short_desc>
      <long_desc>Vehicle assumed landed if no altitude changes happened during this time on low throttle.</long_desc>
      <min>0.0</min>
      <max>10.0</max>
      <unit>s</unit>
    </parameter>
    <parameter default="0.7" name="INAV_LAND_DISP" type="FLOAT">
      <short_desc>Land detector altitude dispersion threshold</short_desc>
      <long_desc>Dispersion threshold for triggering land detector.</long_desc>
      <min>0.0</min>
      <max>10.0</max>
      <unit>m</unit>
    </parameter>
    <parameter default="0.2" name="INAV_LAND_THR" type="FLOAT">
      <short_desc>Land detector throttle threshold</short_desc>
      <long_desc>Value should be lower than minimal hovering thrust. Half of it is good choice.</long_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="0.2" name="INAV_DELAY_GPS" type="FLOAT">
      <short_desc>GPS delay</short_desc>
      <long_desc>GPS delay compensation</long_desc>
      <min>0.0</min>
      <max>1.0</max>
      <unit>s</unit>
    </parameter>
2129 2130 2131 2132 2133 2134 2135 2136 2137 2138 2139 2140 2141 2142
    <parameter default="0.0" name="INAV_FLOW_DIST_X" type="FLOAT">
      <short_desc>Flow module offset (center of rotation) in X direction</short_desc>
      <long_desc>Yaw X flow compensation</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
      <unit>m</unit>
    </parameter>
    <parameter default="0.0" name="INAV_FLOW_DIST_Y" type="FLOAT">
      <short_desc>Flow module offset (center of rotation) in Y direction</short_desc>
      <long_desc>Yaw Y flow compensation</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
      <unit>m</unit>
    </parameter>
2143 2144 2145 2146 2147 2148 2149 2150
    <parameter default="0" name="CBRK_NO_VISION" type="INT32">
      <short_desc>Disable vision input</short_desc>
      <long_desc>Set to the appropriate key (328754) to disable vision input.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="1" name="INAV_ENABLED" type="INT32">
      <short_desc>INAV enabled</short_desc>
Don Gagne's avatar
Don Gagne committed
2151
      <long_desc>If set to 1, use INAV for position estimation. Else the system uses the combined attitude / position filter framework.</long_desc>
2152 2153 2154 2155 2156
      <min>0</min>
      <max>1</max>
    </parameter>
  </group>
  <group name="Radio Calibration">
Don Gagne's avatar
Don Gagne committed
2157 2158 2159 2160 2161 2162 2163 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174
    <parameter default="0.0" name="TRIM_ROLL" type="FLOAT">
      <short_desc>Roll trim</short_desc>
      <long_desc>The trim value is the actuator control value the system needs for straight and level flight. It can be calibrated by flying manually straight and level using the RC trims and copying them using the GCS.</long_desc>
      <min>-0.25</min>
      <max>0.25</max>
    </parameter>
    <parameter default="0.0" name="TRIM_PITCH" type="FLOAT">
      <short_desc>Pitch trim</short_desc>
      <long_desc>The trim value is the actuator control value the system needs for straight and level flight. It can be calibrated by flying manually straight and level using the RC trims and copying them using the GCS.</long_desc>
      <min>-0.25</min>
      <max>0.25</max>
    </parameter>
    <parameter default="0.0" name="TRIM_YAW" type="FLOAT">
      <short_desc>Yaw trim</short_desc>
      <long_desc>The trim value is the actuator control value the system needs for straight and level flight. It can be calibrated by flying manually straight and level using the RC trims and copying them using the GCS.</long_desc>
      <min>-0.25</min>
      <max>0.25</max>
    </parameter>
2175 2176 2177 2178 2179
    <parameter default="1000.0" name="RC1_MIN" type="FLOAT">
      <short_desc>RC Channel 1 Minimum</short_desc>
      <long_desc>Minimum value for RC channel 1</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
Don Gagne's avatar
Don Gagne committed
2180
      <unit>us</unit>
2181 2182 2183 2184 2185 2186
    </parameter>
    <parameter default="1500.0" name="RC1_TRIM" type="FLOAT">
      <short_desc>RC Channel 1 Trim</short_desc>
      <long_desc>Mid point value (same as min for throttle)</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
Don Gagne's avatar
Don Gagne committed
2187
      <unit>us</unit>
2188 2189 2190 2191 2192 2193
    </parameter>
    <parameter default="2000.0" name="RC1_MAX" type="FLOAT">
      <short_desc>RC Channel 1 Maximum</short_desc>
      <long_desc>Maximum value for RC channel 1</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
Don Gagne's avatar
Don Gagne committed
2194
      <unit>us</unit>
2195 2196 2197 2198 2199 2200 2201 2202 2203 2204 2205 2206
    </parameter>
    <parameter default="1.0" name="RC1_REV" type="FLOAT">
      <short_desc>RC Channel 1 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="10.0" name="RC1_DZ" type="FLOAT">
      <short_desc>RC Channel 1 dead zone</short_desc>
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
Don Gagne's avatar
Don Gagne committed
2207
      <unit>us</unit>
2208 2209 2210
    </parameter>
    <parameter default="1000.0" name="RC2_MIN" type="FLOAT">
      <short_desc>RC Channel 2 Minimum</short_desc>
Don Gagne's avatar
Don Gagne committed
2211
      <long_desc>Minimum value for this channel.</long_desc>
2212 2213
      <min>800.0</min>
      <max>1500.0</max>
Don Gagne's avatar
Don Gagne committed
2214
      <unit>us</unit>
2215 2216 2217
    </parameter>
    <parameter default="1500.0" name="RC2_TRIM" type="FLOAT">
      <short_desc>RC Channel 2 Trim</short_desc>
Don Gagne's avatar
Don Gagne committed
2218
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
2219 2220
      <min>800.0</min>
      <max>2200.0</max>
Don Gagne's avatar
Don Gagne committed
2221
      <unit>us</unit>
2222 2223 2224
    </parameter>
    <parameter default="2000.0" name="RC2_MAX" type="FLOAT">
      <short_desc>RC Channel 2 Maximum</short_desc>
Don Gagne's avatar
Don Gagne committed
2225
      <long_desc>Maximum value for this channel.</long_desc>
2226 2227
      <min>1500.0</min>
      <max>2200.0</max>
Don Gagne's avatar
Don Gagne committed
2228
      <unit>us</unit>
2229 2230 2231 2232 2233 2234 2235 2236 2237 2238 2239 2240
    </parameter>
    <parameter default="1.0" name="RC2_REV" type="FLOAT">
      <short_desc>RC Channel 2 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="10.0" name="RC2_DZ" type="FLOAT">
      <short_desc>RC Channel 2 dead zone</short_desc>
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
Don Gagne's avatar
Don Gagne committed
2241
      <unit>us</unit>
2242 2243
    </parameter>
    <parameter default="1000" name="RC3_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2244 2245 2246 2247 2248
      <short_desc>RC Channel 3 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2249 2250
    </parameter>
    <parameter default="1500" name="RC3_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2251 2252 2253 2254 2255
      <short_desc>RC Channel 3 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2256 2257
    </parameter>
    <parameter default="2000" name="RC3_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2258 2259 2260 2261 2262
      <short_desc>RC Channel 3 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2263 2264
    </parameter>
    <parameter default="1.0" name="RC3_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2265 2266 2267 2268
      <short_desc>RC Channel 3 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2269 2270
    </parameter>
    <parameter default="10.0" name="RC3_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2271
      <short_desc>RC Channel 3 dead zone</short_desc>
2272 2273 2274
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
Don Gagne's avatar
Don Gagne committed
2275
      <unit>us</unit>
2276 2277
    </parameter>
    <parameter default="1000" name="RC4_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2278 2279 2280 2281 2282
      <short_desc>RC Channel 4 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2283 2284
    </parameter>
    <parameter default="1500" name="RC4_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2285 2286 2287 2288 2289
      <short_desc>RC Channel 4 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2290 2291
    </parameter>
    <parameter default="2000" name="RC4_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2292 2293 2294 2295 2296
      <short_desc>RC Channel 4 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2297 2298
    </parameter>
    <parameter default="1.0" name="RC4_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2299 2300 2301 2302
      <short_desc>RC Channel 4 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2303 2304
    </parameter>
    <parameter default="10.0" name="RC4_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2305
      <short_desc>RC Channel 4 dead zone</short_desc>
2306 2307 2308
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
Don Gagne's avatar
Don Gagne committed
2309
      <unit>us</unit>
2310 2311
    </parameter>
    <parameter default="1000" name="RC5_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2312 2313 2314 2315 2316
      <short_desc>RC Channel 5 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2317 2318
    </parameter>
    <parameter default="1500" name="RC5_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2319 2320 2321 2322 2323
      <short_desc>RC Channel 5 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2324 2325
    </parameter>
    <parameter default="2000" name="RC5_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2326 2327 2328 2329 2330
      <short_desc>RC Channel 5 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2331 2332
    </parameter>
    <parameter default="1.0" name="RC5_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2333 2334 2335 2336
      <short_desc>RC Channel 5 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2337 2338
    </parameter>
    <parameter default="10.0" name="RC5_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2339
      <short_desc>RC Channel 5 dead zone</short_desc>
2340 2341 2342 2343 2344
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC6_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2345 2346 2347 2348
      <short_desc>RC Channel 6 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
2349 2350
    </parameter>
    <parameter default="1500" name="RC6_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2351 2352 2353 2354 2355
      <short_desc>RC Channel 6 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2356 2357
    </parameter>
    <parameter default="2000" name="RC6_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2358 2359 2360 2361 2362
      <short_desc>RC Channel 6 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2363 2364
    </parameter>
    <parameter default="1.0" name="RC6_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2365 2366 2367 2368
      <short_desc>RC Channel 6 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2369 2370
    </parameter>
    <parameter default="10.0" name="RC6_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2371
      <short_desc>RC Channel 6 dead zone</short_desc>
2372 2373 2374 2375 2376
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC7_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2377 2378 2379 2380
      <short_desc>RC Channel 7 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
2381 2382
    </parameter>
    <parameter default="1500" name="RC7_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2383 2384 2385 2386 2387
      <short_desc>RC Channel 7 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2388 2389
    </parameter>
    <parameter default="2000" name="RC7_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2390 2391 2392 2393 2394
      <short_desc>RC Channel 7 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2395 2396
    </parameter>
    <parameter default="1.0" name="RC7_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2397 2398 2399 2400
      <short_desc>RC Channel 7 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2401 2402
    </parameter>
    <parameter default="10.0" name="RC7_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2403
      <short_desc>RC Channel 7 dead zone</short_desc>
2404 2405 2406 2407 2408
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC8_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2409 2410 2411 2412 2413
      <short_desc>RC Channel 8 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2414 2415
    </parameter>
    <parameter default="1500" name="RC8_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2416 2417 2418 2419 2420
      <short_desc>RC Channel 8 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2421 2422
    </parameter>
    <parameter default="2000" name="RC8_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2423 2424 2425 2426 2427
      <short_desc>RC Channel 8 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2428 2429
    </parameter>
    <parameter default="1.0" name="RC8_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2430 2431 2432 2433
      <short_desc>RC Channel 8 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2434 2435
    </parameter>
    <parameter default="10.0" name="RC8_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2436
      <short_desc>RC Channel 8 dead zone</short_desc>
2437 2438 2439 2440 2441
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC9_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2442 2443 2444 2445 2446
      <short_desc>RC Channel 9 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2447 2448
    </parameter>
    <parameter default="1500" name="RC9_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2449 2450 2451 2452 2453
      <short_desc>RC Channel 9 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2454 2455
    </parameter>
    <parameter default="2000" name="RC9_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2456 2457 2458 2459 2460
      <short_desc>RC Channel 9 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2461 2462
    </parameter>
    <parameter default="1.0" name="RC9_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2463 2464 2465 2466
      <short_desc>RC Channel 9 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2467 2468
    </parameter>
    <parameter default="0.0" name="RC9_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2469
      <short_desc>RC Channel 9 dead zone</short_desc>
2470 2471 2472 2473 2474
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC10_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2475 2476 2477 2478 2479
      <short_desc>RC Channel 10 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2480 2481
    </parameter>
    <parameter default="1500" name="RC10_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2482 2483 2484 2485 2486
      <short_desc>RC Channel 10 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2487 2488
    </parameter>
    <parameter default="2000" name="RC10_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2489 2490 2491 2492 2493
      <short_desc>RC Channel 10 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2494 2495
    </parameter>
    <parameter default="1.0" name="RC10_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2496 2497 2498 2499
      <short_desc>RC Channel 10 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2500 2501
    </parameter>
    <parameter default="0.0" name="RC10_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2502
      <short_desc>RC Channel 10 dead zone</short_desc>
2503 2504 2505 2506 2507
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC11_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2508 2509 2510 2511 2512
      <short_desc>RC Channel 11 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2513 2514
    </parameter>
    <parameter default="1500" name="RC11_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2515 2516 2517 2518 2519
      <short_desc>RC Channel 11 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2520 2521
    </parameter>
    <parameter default="2000" name="RC11_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2522 2523 2524 2525 2526
      <short_desc>RC Channel 11 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2527 2528
    </parameter>
    <parameter default="1.0" name="RC11_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2529 2530 2531 2532
      <short_desc>RC Channel 11 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2533 2534
    </parameter>
    <parameter default="0.0" name="RC11_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2535
      <short_desc>RC Channel 11 dead zone</short_desc>
2536 2537 2538 2539 2540
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC12_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2541 2542 2543 2544 2545
      <short_desc>RC Channel 12 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2546 2547
    </parameter>
    <parameter default="1500" name="RC12_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2548 2549 2550 2551 2552
      <short_desc>RC Channel 12 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2553 2554
    </parameter>
    <parameter default="2000" name="RC12_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2555 2556 2557 2558 2559
      <short_desc>RC Channel 12 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2560 2561
    </parameter>
    <parameter default="1.0" name="RC12_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2562 2563 2564 2565
      <short_desc>RC Channel 12 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2566 2567
    </parameter>
    <parameter default="0.0" name="RC12_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2568
      <short_desc>RC Channel 12 dead zone</short_desc>
2569 2570 2571 2572 2573
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC13_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2574 2575 2576 2577 2578
      <short_desc>RC Channel 13 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2579 2580
    </parameter>
    <parameter default="1500" name="RC13_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2581 2582 2583 2584 2585
      <short_desc>RC Channel 13 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2586 2587
    </parameter>
    <parameter default="2000" name="RC13_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2588 2589 2590 2591 2592
      <short_desc>RC Channel 13 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2593 2594
    </parameter>
    <parameter default="1.0" name="RC13_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2595 2596 2597 2598
      <short_desc>RC Channel 13 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2599 2600
    </parameter>
    <parameter default="0.0" name="RC13_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2601
      <short_desc>RC Channel 13 dead zone</short_desc>
2602 2603 2604 2605 2606
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC14_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2607 2608 2609 2610 2611
      <short_desc>RC Channel 14 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2612 2613
    </parameter>
    <parameter default="1500" name="RC14_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2614 2615 2616 2617 2618 2619 2620 2621 2622 2623 2624 2625
      <short_desc>RC Channel 14 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
    </parameter>
    <parameter default="2000" name="RC14_MAX" type="FLOAT">
      <short_desc>RC Channel 14 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2626 2627
    </parameter>
    <parameter default="1.0" name="RC14_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2628 2629 2630 2631
      <short_desc>RC Channel 14 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2632 2633
    </parameter>
    <parameter default="0.0" name="RC14_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2634
      <short_desc>RC Channel 14 dead zone</short_desc>
2635 2636 2637 2638 2639
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC15_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2640 2641 2642 2643 2644
      <short_desc>RC Channel 15 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2645 2646
    </parameter>
    <parameter default="1500" name="RC15_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2647 2648 2649 2650 2651
      <short_desc>RC Channel 15 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2652 2653
    </parameter>
    <parameter default="2000" name="RC15_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2654 2655 2656 2657 2658
      <short_desc>RC Channel 15 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2659 2660
    </parameter>
    <parameter default="1.0" name="RC15_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2661 2662 2663 2664
      <short_desc>RC Channel 15 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2665 2666
    </parameter>
    <parameter default="0.0" name="RC15_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2667
      <short_desc>RC Channel 15 dead zone</short_desc>
2668 2669 2670 2671 2672
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC16_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2673 2674 2675 2676 2677
      <short_desc>RC Channel 16 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2678 2679
    </parameter>
    <parameter default="1500" name="RC16_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2680 2681 2682 2683 2684
      <short_desc>RC Channel 16 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2685 2686
    </parameter>
    <parameter default="2000" name="RC16_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2687 2688 2689 2690 2691
      <short_desc>RC Channel 16 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2692 2693
    </parameter>
    <parameter default="1.0" name="RC16_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2694 2695 2696 2697
      <short_desc>RC Channel 16 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2698 2699
    </parameter>
    <parameter default="0.0" name="RC16_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2700
      <short_desc>RC Channel 16 dead zone</short_desc>
2701 2702 2703 2704 2705
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC17_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2706 2707 2708 2709 2710
      <short_desc>RC Channel 17 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2711 2712
    </parameter>
    <parameter default="1500" name="RC17_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2713 2714 2715 2716 2717
      <short_desc>RC Channel 17 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2718 2719
    </parameter>
    <parameter default="2000" name="RC17_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2720 2721 2722 2723 2724
      <short_desc>RC Channel 17 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2725 2726
    </parameter>
    <parameter default="1.0" name="RC17_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2727 2728 2729 2730
      <short_desc>RC Channel 17 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2731 2732
    </parameter>
    <parameter default="0.0" name="RC17_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2733
      <short_desc>RC Channel 17 dead zone</short_desc>
2734 2735 2736 2737 2738
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
    <parameter default="1000" name="RC18_MIN" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2739 2740 2741 2742 2743
      <short_desc>RC Channel 18 Minimum</short_desc>
      <long_desc>Minimum value for this channel.</long_desc>
      <min>800.0</min>
      <max>1500.0</max>
      <unit>us</unit>
2744 2745
    </parameter>
    <parameter default="1500" name="RC18_TRIM" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2746 2747 2748 2749 2750
      <short_desc>RC Channel 18 Trim</short_desc>
      <long_desc>Mid point value (has to be set to the same as min for throttle channel).</long_desc>
      <min>800.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2751 2752
    </parameter>
    <parameter default="2000" name="RC18_MAX" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2753 2754 2755 2756 2757
      <short_desc>RC Channel 18 Maximum</short_desc>
      <long_desc>Maximum value for this channel.</long_desc>
      <min>1500.0</min>
      <max>2200.0</max>
      <unit>us</unit>
2758 2759
    </parameter>
    <parameter default="1.0" name="RC18_REV" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2760 2761 2762 2763
      <short_desc>RC Channel 18 Reverse</short_desc>
      <long_desc>Set to -1 to reverse channel.</long_desc>
      <min>-1.0</min>
      <max>1.0</max>
2764 2765
    </parameter>
    <parameter default="0.0" name="RC18_DZ" type="FLOAT">
Don Gagne's avatar
Don Gagne committed
2766
      <short_desc>RC Channel 18 dead zone</short_desc>
2767 2768 2769 2770
      <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
      <min>0.0</min>
      <max>100.0</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
2771 2772 2773 2774 2775
    <parameter default="0" name="RC_RL1_DSM_VCC" type="INT32">
      <short_desc>Enable relay control of relay 1 mapped to the Spektrum receiver power supply</short_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
2776 2777 2778 2779 2780 2781
    <parameter default="-1" name="RC_DSM_BIND" type="INT32">
      <short_desc>DSM binding trigger</short_desc>
      <long_desc>-1 = Idle, 0 = Start DSM2 bind, 1 = Start DSMX bind</long_desc>
    </parameter>
    <parameter default="0" name="RC_CHAN_CNT" type="INT32">
      <short_desc>RC channel count</short_desc>
Don Gagne's avatar
Don Gagne committed
2782
      <long_desc>This parameter is used by Ground Station software to save the number of channels which were used during RC calibration. It is only meant for ground station use.</long_desc>
2783 2784 2785 2786 2787
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="1" name="RC_TH_USER" type="INT32">
      <short_desc>RC mode switch threshold automaic distribution</short_desc>
Don Gagne's avatar
Don Gagne committed
2788
      <long_desc>This parameter is used by Ground Station software to specify whether the threshold values for flight mode switches were automatically calculated. 0 indicates that the threshold values were set by the user. Any other value indicates that the threshold value where automatically set by the ground station software. It is only meant for ground station use.</long_desc>
2789 2790 2791
      <min>0</min>
      <max>1</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
2792
    <parameter default="0" name="RC_MAP_ROLL" type="INT32">
2793
      <short_desc>Roll control channel mapping</short_desc>
Don Gagne's avatar
Don Gagne committed
2794
      <long_desc>The channel index (starting from 1 for channel 1) indicates which channel should be used for reading roll inputs from. A value of zero indicates the switch is not assigned.</long_desc>
2795 2796 2797
      <min>0</min>
      <max>18</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
2798
    <parameter default="0" name="RC_MAP_PITCH" type="INT32">
2799
      <short_desc>Pitch control channel mapping</short_desc>
Don Gagne's avatar
Don Gagne committed
2800
      <long_desc>The channel index (starting from 1 for channel 1) indicates which channel should be used for reading pitch inputs from. A value of zero indicates the switch is not assigned.</long_desc>
2801 2802 2803
      <min>0</min>
      <max>18</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
2804
    <parameter default="0" name="RC_MAP_THROTTLE" type="INT32">
2805
      <short_desc>Throttle control channel mapping</short_desc>
Don Gagne's avatar
Don Gagne committed
2806
      <long_desc>The channel index (starting from 1 for channel 1) indicates which channel should be used for reading throttle inputs from. A value of zero indicates the switch is not assigned.</long_desc>
2807 2808 2809
      <min>0</min>
      <max>18</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
2810
    <parameter default="0" name="RC_MAP_YAW" type="INT32">
2811
      <short_desc>Yaw control channel mapping</short_desc>
Don Gagne's avatar
Don Gagne committed
2812
      <long_desc>The channel index (starting from 1 for channel 1) indicates which channel should be used for reading yaw inputs from. A value of zero indicates the switch is not assigned.</long_desc>
2813 2814 2815 2816 2817 2818 2819 2820 2821 2822 2823 2824 2825 2826 2827 2828 2829 2830 2831 2832 2833 2834 2835
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0" name="RC_MAP_AUX1" type="INT32">
      <short_desc>Auxiliary switch 1 channel mapping</short_desc>
      <long_desc>Default function: Camera pitch</long_desc>
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0" name="RC_MAP_AUX2" type="INT32">
      <short_desc>Auxiliary switch 2 channel mapping</short_desc>
      <long_desc>Default function: Camera roll</long_desc>
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0" name="RC_MAP_AUX3" type="INT32">
      <short_desc>Auxiliary switch 3 channel mapping</short_desc>
      <long_desc>Default function: Camera azimuth / yaw</long_desc>
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0" name="RC_MAP_PARAM1" type="INT32">
      <short_desc>Channel which changes a parameter</short_desc>
Don Gagne's avatar
Don Gagne committed
2836
      <long_desc>Can be used for parameter tuning with the RC. This one is further referenced as the 1st parameter channel. Set to 0 to deactivate *</long_desc>
2837 2838 2839 2840 2841
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0" name="RC_MAP_PARAM2" type="INT32">
      <short_desc>Channel which changes a parameter</short_desc>
Don Gagne's avatar
Don Gagne committed
2842
      <long_desc>Can be used for parameter tuning with the RC. This one is further referenced as the 2nd parameter channel. Set to 0 to deactivate *</long_desc>
2843 2844 2845 2846 2847
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0" name="RC_MAP_PARAM3" type="INT32">
      <short_desc>Channel which changes a parameter</short_desc>
Don Gagne's avatar
Don Gagne committed
2848
      <long_desc>Can be used for parameter tuning with the RC. This one is further referenced as the 3th parameter channel. Set to 0 to deactivate *</long_desc>
2849 2850 2851 2852 2853
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0" name="RC_FAILS_THR" type="INT32">
      <short_desc>Failsafe channel PWM threshold</short_desc>
Don Gagne's avatar
Don Gagne committed
2854 2855
      <long_desc>Set to a value slightly above the PWM value assumed by throttle in a failsafe event, but ensure it is below the PWM value assumed by throttle during normal operation.</long_desc>
      <min>0</min>
2856
      <max>2200</max>
Don Gagne's avatar
Don Gagne committed
2857
      <unit>us</unit>
2858 2859 2860
    </parameter>
    <parameter default="0" name="RC_RSSI_PWM_CHAN" type="INT32">
      <short_desc>PWM input channel that provides RSSI</short_desc>
Don Gagne's avatar
Don Gagne committed
2861
      <long_desc>0: do not read RSSI from input channel 1-18: read RSSI from specified input channel Specify the range for RSSI input with RC_RSSI_PWM_MIN and RC_RSSI_PWM_MAX parameters.</long_desc>
2862 2863 2864 2865 2866 2867 2868 2869 2870 2871 2872 2873 2874 2875 2876 2877 2878 2879 2880
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="1000" name="RC_RSSI_PWM_MAX" type="INT32">
      <short_desc>Max input value for RSSI reading</short_desc>
      <long_desc>Only used if RC_RSSI_PWM_CHAN &gt; 0</long_desc>
      <min>0</min>
      <max>2000</max>
    </parameter>
    <parameter default="2000" name="RC_RSSI_PWM_MIN" type="INT32">
      <short_desc>Min input value for RSSI reading</short_desc>
      <long_desc>Only used if RC_RSSI_PWM_CHAN &gt; 0</long_desc>
      <min>0</min>
      <max>2000</max>
    </parameter>
  </group>
  <group name="Radio Signal Loss">
    <parameter default="120.0" name="NAV_RCL_LT" type="FLOAT">
      <short_desc>Loiter Time</short_desc>
Don Gagne's avatar
Don Gagne committed
2881
      <long_desc>The amount of time in seconds the system should loiter at current position before termination Set to -1 to make the system skip loitering</long_desc>
2882 2883 2884 2885 2886 2887 2888
      <min>-1.0</min>
      <unit>seconds</unit>
    </parameter>
  </group>
  <group name="Radio Switches">
    <parameter default="0" name="RC_MAP_MODE_SW" type="INT32">
      <short_desc>Mode switch channel mapping</short_desc>
Don Gagne's avatar
Don Gagne committed
2889
      <long_desc>This is the main flight mode selector. The channel index (starting from 1 for channel 1) indicates which channel should be used for deciding about the main mode. A value of zero indicates the switch is not assigned.</long_desc>
2890 2891 2892 2893 2894 2895 2896 2897
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0" name="RC_MAP_RETURN_SW" type="INT32">
      <short_desc>Return switch channel mapping</short_desc>
      <min>0</min>
      <max>18</max>
    </parameter>
2898 2899 2900 2901 2902
    <parameter default="0" name="RC_MAP_RATT_SW" type="INT32">
      <short_desc>Rattitude switch channel mapping</short_desc>
      <min>0</min>
      <max>18</max>
    </parameter>
2903 2904 2905 2906 2907 2908 2909 2910 2911 2912 2913 2914 2915 2916 2917 2918 2919 2920 2921 2922 2923 2924 2925 2926 2927 2928 2929
    <parameter default="0" name="RC_MAP_POSCTL_SW" type="INT32">
      <short_desc>Posctl switch channel mapping</short_desc>
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0" name="RC_MAP_LOITER_SW" type="INT32">
      <short_desc>Loiter switch channel mapping</short_desc>
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0" name="RC_MAP_ACRO_SW" type="INT32">
      <short_desc>Acro switch channel mapping</short_desc>
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0" name="RC_MAP_OFFB_SW" type="INT32">
      <short_desc>Offboard switch channel mapping</short_desc>
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0" name="RC_MAP_FLAPS" type="INT32">
      <short_desc>Flaps channel mapping</short_desc>
      <min>0</min>
      <max>18</max>
    </parameter>
    <parameter default="0.25" name="RC_ASSIST_TH" type="FLOAT">
      <short_desc>Threshold for selecting assist mode</short_desc>
Don Gagne's avatar
Don Gagne committed
2930
      <long_desc>0-1 indicate where in the full channel range the threshold sits 0 : min 1 : max sign indicates polarity of comparison positive : true when channel&gt;th negative : true when channel&lt;th</long_desc>
2931 2932 2933 2934 2935
      <min>-1</min>
      <max>1</max>
    </parameter>
    <parameter default="0.75" name="RC_AUTO_TH" type="FLOAT">
      <short_desc>Threshold for selecting auto mode</short_desc>
Don Gagne's avatar
Don Gagne committed
2936
      <long_desc>0-1 indicate where in the full channel range the threshold sits 0 : min 1 : max sign indicates polarity of comparison positive : true when channel&gt;th negative : true when channel&lt;th</long_desc>
2937 2938 2939
      <min>-1</min>
      <max>1</max>
    </parameter>
2940 2941 2942 2943 2944 2945
    <parameter default="0.5" name="RC_RATT_TH" type="FLOAT">
      <short_desc>Threshold for selecting rattitude mode</short_desc>
      <long_desc>0-1 indicate where in the full channel range the threshold sits 0 : min 1 : max sign indicates polarity of comparison positive : true when channel&gt;th negative : true when channel&lt;th</long_desc>
      <min>-1</min>
      <max>1</max>
    </parameter>
2946 2947
    <parameter default="0.5" name="RC_POSCTL_TH" type="FLOAT">
      <short_desc>Threshold for selecting posctl mode</short_desc>
Don Gagne's avatar
Don Gagne committed
2948
      <long_desc>0-1 indicate where in the full channel range the threshold sits 0 : min 1 : max sign indicates polarity of comparison positive : true when channel&gt;th negative : true when channel&lt;th</long_desc>
2949 2950 2951 2952 2953
      <min>-1</min>
      <max>1</max>
    </parameter>
    <parameter default="0.5" name="RC_RETURN_TH" type="FLOAT">
      <short_desc>Threshold for selecting return to launch mode</short_desc>
Don Gagne's avatar
Don Gagne committed
2954
      <long_desc>0-1 indicate where in the full channel range the threshold sits 0 : min 1 : max sign indicates polarity of comparison positive : true when channel&gt;th negative : true when channel&lt;th</long_desc>
2955 2956 2957 2958 2959
      <min>-1</min>
      <max>1</max>
    </parameter>
    <parameter default="0.5" name="RC_LOITER_TH" type="FLOAT">
      <short_desc>Threshold for selecting loiter mode</short_desc>
Don Gagne's avatar
Don Gagne committed
2960
      <long_desc>0-1 indicate where in the full channel range the threshold sits 0 : min 1 : max sign indicates polarity of comparison positive : true when channel&gt;th negative : true when channel&lt;th</long_desc>
2961 2962 2963 2964 2965
      <min>-1</min>
      <max>1</max>
    </parameter>
    <parameter default="0.5" name="RC_ACRO_TH" type="FLOAT">
      <short_desc>Threshold for selecting acro mode</short_desc>
Don Gagne's avatar
Don Gagne committed
2966
      <long_desc>0-1 indicate where in the full channel range the threshold sits 0 : min 1 : max sign indicates polarity of comparison positive : true when channel&gt;th negative : true when channel&lt;th</long_desc>
2967 2968 2969 2970 2971
      <min>-1</min>
      <max>1</max>
    </parameter>
    <parameter default="0.5" name="RC_OFFB_TH" type="FLOAT">
      <short_desc>Threshold for selecting offboard mode</short_desc>
Don Gagne's avatar
Don Gagne committed
2972
      <long_desc>0-1 indicate where in the full channel range the threshold sits 0 : min 1 : max sign indicates polarity of comparison positive : true when channel&gt;th negative : true when channel&lt;th</long_desc>
2973 2974 2975 2976 2977 2978 2979 2980 2981 2982 2983 2984 2985 2986
      <min>-1</min>
      <max>1</max>
    </parameter>
  </group>
  <group name="Return To Land">
    <parameter default="60" name="RTL_RETURN_ALT" type="FLOAT">
      <short_desc>RTL altitude</short_desc>
      <long_desc>Altitude to fly back in RTL in meters</long_desc>
      <min>0</min>
      <max>150</max>
      <unit>meters</unit>
    </parameter>
    <parameter default="30" name="RTL_DESCEND_ALT" type="FLOAT">
      <short_desc>RTL loiter altitude</short_desc>
Don Gagne's avatar
Don Gagne committed
2987
      <long_desc>Stay at this altitude above home position after RTL descending. Land (i.e. slowly descend) from this altitude if autolanding allowed.</long_desc>
2988 2989 2990 2991 2992 2993
      <min>2</min>
      <max>100</max>
      <unit>meters</unit>
    </parameter>
    <parameter default="-1.0" name="RTL_LAND_DELAY" type="FLOAT">
      <short_desc>RTL delay</short_desc>
Don Gagne's avatar
Don Gagne committed
2994
      <long_desc>Delay after descend before landing in RTL mode. If set to -1 the system will not land but loiter at NAV_LAND_ALT.</long_desc>
2995 2996 2997 2998 2999 3000 3001 3002
      <min>-1</min>
      <max>300</max>
      <unit>seconds</unit>
    </parameter>
  </group>
  <group name="SD Logging">
    <parameter default="-1" name="SDLOG_RATE" type="INT32">
      <short_desc>Logging rate</short_desc>
Don Gagne's avatar
Don Gagne committed
3003
      <long_desc>A value of -1 indicates the commandline argument should be obeyed. A value of 0 sets the minimum rate, any other value is interpreted as rate in Hertz. This parameter is only read out before logging starts (which commonly is before arming).</long_desc>
3004
      <min>-1</min>
3005
      <max>100</max>
3006 3007 3008
    </parameter>
    <parameter default="-1" name="SDLOG_EXT" type="INT32">
      <short_desc>Enable extended logging mode</short_desc>
Don Gagne's avatar
Don Gagne committed
3009
      <long_desc>A value of -1 indicates the commandline argument should be obeyed. A value of 0 disables extended logging mode, a value of 1 enables it. This parameter is only read out before logging starts (which commonly is before arming).</long_desc>
3010 3011 3012
      <min>-1</min>
      <max>1</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
3013
    <parameter default="1" name="SDLOG_GPSTIME" type="INT32">
3014
      <short_desc>Use timestamps only if GPS 3D fix is available</short_desc>
Don Gagne's avatar
Don Gagne committed
3015
      <long_desc>A value of 1 constrains the log folder creation to only use the time stamp if a 3D GPS lock is present.</long_desc>
3016 3017 3018 3019 3020 3021 3022 3023 3024 3025 3026 3027 3028 3029 3030 3031 3032 3033 3034 3035 3036 3037 3038 3039 3040 3041 3042 3043 3044 3045 3046 3047 3048 3049 3050 3051 3052 3053 3054 3055 3056 3057 3058 3059 3060 3061
      <min>0</min>
      <max>1</max>
    </parameter>
  </group>
  <group name="Sensor Calibration">
    <parameter default="0" name="CAL_BOARD_ID" type="INT32">
      <short_desc>ID of the board this parameter set was calibrated on</short_desc>
    </parameter>
    <parameter default="0" name="CAL_GYRO0_ID" type="INT32">
      <short_desc>ID of the Gyro that the calibration is for</short_desc>
    </parameter>
    <parameter default="0.0" name="CAL_GYRO0_XOFF" type="FLOAT">
      <short_desc>Gyro X-axis offset</short_desc>
      <min>-10.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.0" name="CAL_GYRO0_YOFF" type="FLOAT">
      <short_desc>Gyro Y-axis offset</short_desc>
      <min>-10.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.0" name="CAL_GYRO0_ZOFF" type="FLOAT">
      <short_desc>Gyro Z-axis offset</short_desc>
      <min>-5.0</min>
      <max>5.0</max>
    </parameter>
    <parameter default="1.0" name="CAL_GYRO0_XSCALE" type="FLOAT">
      <short_desc>Gyro X-axis scaling factor</short_desc>
      <min>-1.5</min>
      <max>1.5</max>
    </parameter>
    <parameter default="1.0" name="CAL_GYRO0_YSCALE" type="FLOAT">
      <short_desc>Gyro Y-axis scaling factor</short_desc>
      <min>-1.5</min>
      <max>1.5</max>
    </parameter>
    <parameter default="1.0" name="CAL_GYRO0_ZSCALE" type="FLOAT">
      <short_desc>Gyro Z-axis scaling factor</short_desc>
      <min>-1.5</min>
      <max>1.5</max>
    </parameter>
    <parameter default="0" name="CAL_MAG0_ID" type="INT32">
      <short_desc>ID of Magnetometer the calibration is for</short_desc>
    </parameter>
    <parameter default="-1" name="CAL_MAG0_ROT" type="INT32">
      <short_desc>Rotation of magnetometer 0 relative to airframe</short_desc>
Don Gagne's avatar
Don Gagne committed
3062
      <long_desc>An internal magnetometer will force a value of -1, so a GCS should only attempt to configure the rotation if the value is greater than or equal to zero.</long_desc>
3063 3064 3065 3066 3067 3068 3069 3070 3071 3072 3073 3074 3075 3076 3077 3078 3079 3080 3081 3082 3083 3084 3085 3086 3087 3088 3089 3090 3091 3092 3093 3094 3095 3096 3097 3098 3099 3100 3101 3102 3103 3104 3105 3106 3107 3108 3109 3110 3111 3112 3113 3114 3115 3116 3117 3118 3119 3120 3121 3122 3123 3124 3125 3126 3127 3128 3129 3130 3131 3132 3133 3134 3135 3136 3137 3138 3139 3140 3141 3142 3143 3144 3145 3146 3147 3148
      <min>-1</min>
      <max>30</max>
    </parameter>
    <parameter default="0.0" name="CAL_MAG0_XOFF" type="FLOAT">
      <short_desc>Magnetometer X-axis offset</short_desc>
      <min>-500.0</min>
      <max>500.0</max>
    </parameter>
    <parameter default="0.0" name="CAL_MAG0_YOFF" type="FLOAT">
      <short_desc>Magnetometer Y-axis offset</short_desc>
      <min>-500.0</min>
      <max>500.0</max>
    </parameter>
    <parameter default="0.0" name="CAL_MAG0_ZOFF" type="FLOAT">
      <short_desc>Magnetometer Z-axis offset</short_desc>
      <min>-500.0</min>
      <max>500.0</max>
    </parameter>
    <parameter default="1.0" name="CAL_MAG0_XSCALE" type="FLOAT">
      <short_desc>Magnetometer X-axis scaling factor</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_MAG0_YSCALE" type="FLOAT">
      <short_desc>Magnetometer Y-axis scaling factor</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_MAG0_ZSCALE" type="FLOAT">
      <short_desc>Magnetometer Z-axis scaling factor</short_desc>
    </parameter>
    <parameter default="0" name="CAL_ACC0_ID" type="INT32">
      <short_desc>ID of the Accelerometer that the calibration is for</short_desc>
    </parameter>
    <parameter default="0.0" name="CAL_ACC0_XOFF" type="FLOAT">
      <short_desc>Accelerometer X-axis offset</short_desc>
    </parameter>
    <parameter default="0.0" name="CAL_ACC0_YOFF" type="FLOAT">
      <short_desc>Accelerometer Y-axis offset</short_desc>
    </parameter>
    <parameter default="0.0" name="CAL_ACC0_ZOFF" type="FLOAT">
      <short_desc>Accelerometer Z-axis offset</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_ACC0_XSCALE" type="FLOAT">
      <short_desc>Accelerometer X-axis scaling factor</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_ACC0_YSCALE" type="FLOAT">
      <short_desc>Accelerometer Y-axis scaling factor</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_ACC0_ZSCALE" type="FLOAT">
      <short_desc>Accelerometer Z-axis scaling factor</short_desc>
    </parameter>
    <parameter default="0" name="CAL_GYRO1_ID" type="INT32">
      <short_desc>ID of the Gyro that the calibration is for</short_desc>
    </parameter>
    <parameter default="0.0" name="CAL_GYRO1_XOFF" type="FLOAT">
      <short_desc>Gyro X-axis offset</short_desc>
      <min>-10.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.0" name="CAL_GYRO1_YOFF" type="FLOAT">
      <short_desc>Gyro Y-axis offset</short_desc>
      <min>-10.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.0" name="CAL_GYRO1_ZOFF" type="FLOAT">
      <short_desc>Gyro Z-axis offset</short_desc>
      <min>-5.0</min>
      <max>5.0</max>
    </parameter>
    <parameter default="1.0" name="CAL_GYRO1_XSCALE" type="FLOAT">
      <short_desc>Gyro X-axis scaling factor</short_desc>
      <min>-1.5</min>
      <max>1.5</max>
    </parameter>
    <parameter default="1.0" name="CAL_GYRO1_YSCALE" type="FLOAT">
      <short_desc>Gyro Y-axis scaling factor</short_desc>
      <min>-1.5</min>
      <max>1.5</max>
    </parameter>
    <parameter default="1.0" name="CAL_GYRO1_ZSCALE" type="FLOAT">
      <short_desc>Gyro Z-axis scaling factor</short_desc>
      <min>-1.5</min>
      <max>1.5</max>
    </parameter>
    <parameter default="0" name="CAL_MAG1_ID" type="INT32">
      <short_desc>ID of Magnetometer the calibration is for</short_desc>
    </parameter>
    <parameter default="-1" name="CAL_MAG1_ROT" type="INT32">
      <short_desc>Rotation of magnetometer 1 relative to airframe</short_desc>
Don Gagne's avatar
Don Gagne committed
3149
      <long_desc>An internal magnetometer will force a value of -1, so a GCS should only attempt to configure the rotation if the value is greater than or equal to zero.</long_desc>
3150 3151 3152 3153 3154 3155 3156 3157 3158 3159 3160 3161 3162 3163 3164 3165 3166 3167 3168 3169 3170 3171 3172 3173 3174 3175 3176 3177 3178 3179 3180 3181 3182 3183 3184 3185 3186 3187 3188 3189 3190 3191 3192 3193 3194 3195 3196 3197 3198 3199 3200 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3213 3214 3215 3216 3217 3218 3219 3220 3221 3222 3223 3224 3225 3226 3227 3228 3229 3230 3231 3232 3233 3234 3235
      <min>-1</min>
      <max>30</max>
    </parameter>
    <parameter default="0.0" name="CAL_MAG1_XOFF" type="FLOAT">
      <short_desc>Magnetometer X-axis offset</short_desc>
      <min>-500.0</min>
      <max>500.0</max>
    </parameter>
    <parameter default="0.0" name="CAL_MAG1_YOFF" type="FLOAT">
      <short_desc>Magnetometer Y-axis offset</short_desc>
      <min>-500.0</min>
      <max>500.0</max>
    </parameter>
    <parameter default="0.0" name="CAL_MAG1_ZOFF" type="FLOAT">
      <short_desc>Magnetometer Z-axis offset</short_desc>
      <min>-500.0</min>
      <max>500.0</max>
    </parameter>
    <parameter default="1.0" name="CAL_MAG1_XSCALE" type="FLOAT">
      <short_desc>Magnetometer X-axis scaling factor</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_MAG1_YSCALE" type="FLOAT">
      <short_desc>Magnetometer Y-axis scaling factor</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_MAG1_ZSCALE" type="FLOAT">
      <short_desc>Magnetometer Z-axis scaling factor</short_desc>
    </parameter>
    <parameter default="0" name="CAL_ACC1_ID" type="INT32">
      <short_desc>ID of the Accelerometer that the calibration is for</short_desc>
    </parameter>
    <parameter default="0.0" name="CAL_ACC1_XOFF" type="FLOAT">
      <short_desc>Accelerometer X-axis offset</short_desc>
    </parameter>
    <parameter default="0.0" name="CAL_ACC1_YOFF" type="FLOAT">
      <short_desc>Accelerometer Y-axis offset</short_desc>
    </parameter>
    <parameter default="0.0" name="CAL_ACC1_ZOFF" type="FLOAT">
      <short_desc>Accelerometer Z-axis offset</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_ACC1_XSCALE" type="FLOAT">
      <short_desc>Accelerometer X-axis scaling factor</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_ACC1_YSCALE" type="FLOAT">
      <short_desc>Accelerometer Y-axis scaling factor</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_ACC1_ZSCALE" type="FLOAT">
      <short_desc>Accelerometer Z-axis scaling factor</short_desc>
    </parameter>
    <parameter default="0" name="CAL_GYRO2_ID" type="INT32">
      <short_desc>ID of the Gyro that the calibration is for</short_desc>
    </parameter>
    <parameter default="0.0" name="CAL_GYRO2_XOFF" type="FLOAT">
      <short_desc>Gyro X-axis offset</short_desc>
      <min>-10.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.0" name="CAL_GYRO2_YOFF" type="FLOAT">
      <short_desc>Gyro Y-axis offset</short_desc>
      <min>-10.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.0" name="CAL_GYRO2_ZOFF" type="FLOAT">
      <short_desc>Gyro Z-axis offset</short_desc>
      <min>-5.0</min>
      <max>5.0</max>
    </parameter>
    <parameter default="1.0" name="CAL_GYRO2_XSCALE" type="FLOAT">
      <short_desc>Gyro X-axis scaling factor</short_desc>
      <min>-1.5</min>
      <max>1.5</max>
    </parameter>
    <parameter default="1.0" name="CAL_GYRO2_YSCALE" type="FLOAT">
      <short_desc>Gyro Y-axis scaling factor</short_desc>
      <min>-1.5</min>
      <max>1.5</max>
    </parameter>
    <parameter default="1.0" name="CAL_GYRO2_ZSCALE" type="FLOAT">
      <short_desc>Gyro Z-axis scaling factor</short_desc>
      <min>-1.5</min>
      <max>1.5</max>
    </parameter>
    <parameter default="0" name="CAL_MAG2_ID" type="INT32">
      <short_desc>ID of Magnetometer the calibration is for</short_desc>
    </parameter>
    <parameter default="-1" name="CAL_MAG2_ROT" type="INT32">
      <short_desc>Rotation of magnetometer 2 relative to airframe</short_desc>
Don Gagne's avatar
Don Gagne committed
3236
      <long_desc>An internal magnetometer will force a value of -1, so a GCS should only attempt to configure the rotation if the value is greater than or equal to zero.</long_desc>
3237 3238 3239 3240 3241 3242 3243 3244 3245 3246 3247 3248 3249 3250 3251 3252 3253 3254 3255 3256 3257 3258 3259 3260 3261 3262 3263 3264 3265 3266 3267 3268 3269 3270 3271 3272 3273 3274 3275 3276 3277 3278 3279 3280 3281 3282 3283 3284
      <min>-1</min>
      <max>30</max>
    </parameter>
    <parameter default="0.0" name="CAL_MAG2_XOFF" type="FLOAT">
      <short_desc>Magnetometer X-axis offset</short_desc>
      <min>-500.0</min>
      <max>500.0</max>
    </parameter>
    <parameter default="0.0" name="CAL_MAG2_YOFF" type="FLOAT">
      <short_desc>Magnetometer Y-axis offset</short_desc>
      <min>-500.0</min>
      <max>500.0</max>
    </parameter>
    <parameter default="0.0" name="CAL_MAG2_ZOFF" type="FLOAT">
      <short_desc>Magnetometer Z-axis offset</short_desc>
      <min>-500.0</min>
      <max>500.0</max>
    </parameter>
    <parameter default="1.0" name="CAL_MAG2_XSCALE" type="FLOAT">
      <short_desc>Magnetometer X-axis scaling factor</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_MAG2_YSCALE" type="FLOAT">
      <short_desc>Magnetometer Y-axis scaling factor</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_MAG2_ZSCALE" type="FLOAT">
      <short_desc>Magnetometer Z-axis scaling factor</short_desc>
    </parameter>
    <parameter default="0" name="CAL_ACC2_ID" type="INT32">
      <short_desc>ID of the Accelerometer that the calibration is for</short_desc>
    </parameter>
    <parameter default="0.0" name="CAL_ACC2_XOFF" type="FLOAT">
      <short_desc>Accelerometer X-axis offset</short_desc>
    </parameter>
    <parameter default="0.0" name="CAL_ACC2_YOFF" type="FLOAT">
      <short_desc>Accelerometer Y-axis offset</short_desc>
    </parameter>
    <parameter default="0.0" name="CAL_ACC2_ZOFF" type="FLOAT">
      <short_desc>Accelerometer Z-axis offset</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_ACC2_XSCALE" type="FLOAT">
      <short_desc>Accelerometer X-axis scaling factor</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_ACC2_YSCALE" type="FLOAT">
      <short_desc>Accelerometer Y-axis scaling factor</short_desc>
    </parameter>
    <parameter default="1.0" name="CAL_ACC2_ZSCALE" type="FLOAT">
      <short_desc>Accelerometer Z-axis scaling factor</short_desc>
    </parameter>
3285 3286 3287 3288 3289 3290 3291 3292 3293 3294 3295 3296
    <parameter default="0" name="CAL_ACC_PRIME" type="INT32">
      <short_desc>Primary accel ID</short_desc>
    </parameter>
    <parameter default="0" name="CAL_GYRO_PRIME" type="INT32">
      <short_desc>Primary gyro ID</short_desc>
    </parameter>
    <parameter default="0" name="CAL_MAG_PRIME" type="INT32">
      <short_desc>Primary mag ID</short_desc>
    </parameter>
    <parameter default="0" name="CAL_BARO_PRIME" type="INT32">
      <short_desc>Primary baro ID</short_desc>
    </parameter>
3297 3298 3299 3300 3301 3302
    <parameter default="0.0" name="SENS_DPRES_OFF" type="FLOAT">
      <short_desc>Differential pressure sensor offset</short_desc>
      <long_desc>The offset (zero-reading) in Pascal</long_desc>
    </parameter>
    <parameter default="0" name="SENS_DPRES_ANSC" type="FLOAT">
      <short_desc>Differential pressure sensor analog scaling</short_desc>
Don Gagne's avatar
Don Gagne committed
3303
      <long_desc>Pick the appropriate scaling from the datasheet. this number defines the (linear) conversion from voltage to Pascal (pa). For the MPXV7002DP this is 1000. NOTE: If the sensor always registers zero, try switching the static and dynamic tubes.</long_desc>
3304 3305 3306 3307 3308 3309 3310 3311 3312
    </parameter>
    <parameter default="1013.25" name="SENS_BARO_QNH" type="FLOAT">
      <short_desc>QNH for barometer</short_desc>
      <min>500</min>
      <max>1500</max>
      <unit>hPa</unit>
    </parameter>
    <parameter default="0" name="SENS_BOARD_ROT" type="INT32">
      <short_desc>Board rotation</short_desc>
Don Gagne's avatar
Don Gagne committed
3313
      <long_desc>This parameter defines the rotation of the FMU board relative to the platform. Possible values are: 0 = No rotation 1 = Yaw 45° 2 = Yaw 90° 3 = Yaw 135° 4 = Yaw 180° 5 = Yaw 225° 6 = Yaw 270° 7 = Yaw 315° 8 = Roll 180° 9 = Roll 180°, Yaw 45° 10 = Roll 180°, Yaw 90° 11 = Roll 180°, Yaw 135° 12 = Pitch 180° 13 = Roll 180°, Yaw 225° 14 = Roll 180°, Yaw 270° 15 = Roll 180°, Yaw 315° 16 = Roll 90° 17 = Roll 90°, Yaw 45° 18 = Roll 90°, Yaw 90° 19 = Roll 90°, Yaw 135° 20 = Roll 270° 21 = Roll 270°, Yaw 45° 22 = Roll 270°, Yaw 90° 23 = Roll 270°, Yaw 135° 24 = Pitch 90° 25 = Pitch 270°</long_desc>
3314 3315 3316
    </parameter>
    <parameter default="0" name="SENS_FLOW_ROT" type="INT32">
      <short_desc>PX4Flow board rotation</short_desc>
Don Gagne's avatar
Don Gagne committed
3317
      <long_desc>This parameter defines the rotation of the PX4FLOW board relative to the platform. Zero rotation is defined as Y on flow board pointing towards front of vehicle Possible values are: 0 = No rotation 1 = Yaw 45° 2 = Yaw 90° 3 = Yaw 135° 4 = Yaw 180° 5 = Yaw 225° 6 = Yaw 270° 7 = Yaw 315°</long_desc>
3318 3319 3320
    </parameter>
    <parameter default="0.0" name="SENS_BOARD_Y_OFF" type="FLOAT">
      <short_desc>Board rotation Y (Pitch) offset</short_desc>
Don Gagne's avatar
Don Gagne committed
3321 3322
      <long_desc>This parameter defines a rotational offset in degrees around the Y (Pitch) axis. It allows the user to fine tune the board offset in the event of misalignment.</long_desc>
      <unit>degrees</unit>
3323 3324 3325
    </parameter>
    <parameter default="0.0" name="SENS_BOARD_X_OFF" type="FLOAT">
      <short_desc>Board rotation X (Roll) offset</short_desc>
Don Gagne's avatar
Don Gagne committed
3326 3327
      <long_desc>This parameter defines a rotational offset in degrees around the X (Roll) axis It allows the user to fine tune the board offset in the event of misalignment.</long_desc>
      <unit>degrees</unit>
3328 3329 3330
    </parameter>
    <parameter default="0.0" name="SENS_BOARD_Z_OFF" type="FLOAT">
      <short_desc>Board rotation Z (YAW) offset</short_desc>
Don Gagne's avatar
Don Gagne committed
3331 3332
      <long_desc>This parameter defines a rotational offset in degrees around the Z (Yaw) axis. It allows the user to fine tune the board offset in the event of misalignment.</long_desc>
      <unit>degrees</unit>
3333 3334 3335
    </parameter>
    <parameter default="0" name="SENS_EXT_MAG_ROT" type="INT32">
      <short_desc>External magnetometer rotation</short_desc>
Don Gagne's avatar
Don Gagne committed
3336
      <long_desc>This parameter defines the rotation of the external magnetometer relative to the platform (not relative to the FMU). See SENS_BOARD_ROT for possible values.</long_desc>
3337 3338 3339
    </parameter>
    <parameter default="0" name="SENS_EXT_MAG" type="INT32">
      <short_desc>Set usage of external magnetometer</short_desc>
Don Gagne's avatar
Don Gagne committed
3340
      <long_desc>* Set to 0 (default) to auto-detect (will try to get the external as primary) * Set to 1 to force the external magnetometer as primary * Set to 2 to force the internal magnetometer as primary</long_desc>
3341 3342 3343 3344 3345 3346 3347 3348 3349 3350 3351 3352
      <min>0</min>
      <max>2</max>
    </parameter>
  </group>
  <group name="Sensor Enable">
    <parameter default="0" name="SENS_EN_LL40LS" type="INT32">
      <short_desc>Enable Lidar-Lite (LL40LS) pwm driver</short_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
  </group>
  <group name="Subscriber Example">
Don Gagne's avatar
Don Gagne committed
3353
    <parameter default="100" name="SUB_INTERV" type="INT32">
3354 3355
      <short_desc>Interval of one subscriber in the example in ms</short_desc>
    </parameter>
Don Gagne's avatar
Don Gagne committed
3356
    <parameter default="3.14" name="SUB_TESTF" type="FLOAT">
3357 3358 3359 3360 3361 3362
      <short_desc>Float Demonstration Parameter in the Example</short_desc>
    </parameter>
  </group>
  <group name="System">
    <parameter default="0" name="SYS_AUTOSTART" type="INT32">
      <short_desc>Auto-start script index</short_desc>
3363
      <long_desc>CHANGING THIS VALUE REQUIRES A RESTART. Defines the auto-start script used to bootstrap the system.</long_desc>
3364 3365 3366
    </parameter>
    <parameter default="0" name="SYS_AUTOCONFIG" type="INT32">
      <short_desc>Automatically configure default values</short_desc>
Don Gagne's avatar
Don Gagne committed
3367
      <long_desc>Set to 1 to reset parameters on next system startup (setting defaults). Platform-specific values are used if available. RC* parameters are preserved.</long_desc>
3368 3369 3370 3371 3372 3373 3374 3375 3376 3377 3378 3379 3380 3381 3382 3383 3384
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="1" name="SYS_USE_IO" type="INT32">
      <short_desc>Set usage of IO board</short_desc>
      <long_desc>Can be used to use a standard startup script but with a FMU only set-up. Set to 0 to force the FMU only set-up.</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="2" name="SYS_RESTART_TYPE" type="INT32">
      <short_desc>Set restart type</short_desc>
      <long_desc>Set by px4io to indicate type of restart</long_desc>
      <min>0</min>
      <max>2</max>
    </parameter>
    <parameter default="0" name="SYS_COMPANION" type="INT32">
      <short_desc>Companion computer interface</short_desc>
3385
      <long_desc>CHANGING THIS VALUE REQUIRES A RESTART. Configures the baud rate of the companion computer interface. Set to zero to disable, set to these values to enable (NO OTHER VALUES SUPPORTED!) 921600: enables onboard mode at 921600 baud, 8N1. 57600: enables onboard mode at 57600 baud, 8N1. 157600: enables OSD mode at 57600 baud, 8N1.</long_desc>
3386 3387 3388 3389 3390
      <min>0</min>
      <max>921600</max>
    </parameter>
    <parameter default="1" name="SYS_PARAM_VER" type="INT32">
      <short_desc>Parameter version</short_desc>
Don Gagne's avatar
Don Gagne committed
3391
      <long_desc>This monotonically increasing number encodes the parameter compatibility set. whenever it increases parameters might not be backwards compatible and ground control stations should suggest a fresh configuration.</long_desc>
3392 3393 3394 3395 3396 3397
      <min>0</min>
    </parameter>
  </group>
  <group name="UAVCAN">
    <parameter default="0" name="UAVCAN_ENABLE" type="INT32">
      <short_desc>Enable UAVCAN</short_desc>
3398
      <long_desc>Allowed values: 0 - UAVCAN disabled. 1 - Enabled support for UAVCAN actuators and sensors. 2 - Enabled support for dynamic node ID allocation and firmware update. 3 - Sets the motor control outputs to UAVCAN and enables support for dynamic node ID allocation and firmware update.</long_desc>
3399
      <min>0</min>
3400
      <max>3</max>
3401 3402 3403 3404 3405 3406 3407 3408 3409 3410 3411 3412 3413 3414
    </parameter>
    <parameter default="1" name="UAVCAN_NODE_ID" type="INT32">
      <short_desc>UAVCAN Node ID</short_desc>
      <long_desc>Read the specs at http://uavcan.org to learn more about Node ID.</long_desc>
      <min>1</min>
      <max>125</max>
    </parameter>
    <parameter default="1000000" name="UAVCAN_BITRATE" type="INT32">
      <short_desc>UAVCAN CAN bus bitrate</short_desc>
      <min>20000</min>
      <max>1000000</max>
    </parameter>
  </group>
  <group name="VTOL Attitude Control">
Don Gagne's avatar
Don Gagne committed
3415 3416 3417 3418 3419 3420 3421 3422 3423 3424 3425 3426 3427 3428 3429 3430 3431 3432 3433 3434 3435 3436 3437 3438 3439 3440 3441 3442 3443 3444 3445 3446 3447 3448
    <parameter default="0.6" name="VT_TRANS_THR" type="FLOAT">
      <short_desc>Target throttle value for pusher/puller motor during the transition to fw mode</short_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="0.0" name="VT_TILT_MC" type="FLOAT">
      <short_desc>Position of tilt servo in mc mode</short_desc>
      <long_desc>Position of tilt servo in mc mode</long_desc>
      <min>0.0</min>
      <max>1</max>
    </parameter>
    <parameter default="0.3" name="VT_TILT_TRANS" type="FLOAT">
      <short_desc>Position of tilt servo in transition mode</short_desc>
      <long_desc>Position of tilt servo in transition mode</long_desc>
      <min>0.0</min>
      <max>1</max>
    </parameter>
    <parameter default="1.0" name="VT_TILT_FW" type="FLOAT">
      <short_desc>Position of tilt servo in fw mode</short_desc>
      <long_desc>Position of tilt servo in fw mode</long_desc>
      <min>0.0</min>
      <max>1</max>
    </parameter>
    <parameter default="0.5" name="VT_TRANS_P2_DUR" type="FLOAT">
      <short_desc>Duration of front transition phase 2</short_desc>
      <long_desc>Time in seconds it should take for the rotors to rotate forward completely from the point when the plane has picked up enough airspeed and is ready to go into fixed wind mode.</long_desc>
      <min>0.1</min>
      <max>2</max>
    </parameter>
    <parameter default="0" name="VT_FW_MOT_OFF" type="INT32">
      <short_desc>The channel number of motors that must be turned off in fixed wing mode</short_desc>
      <min>0</min>
      <max>123456</max>
    </parameter>
3449 3450
    <parameter default="0" name="VT_MOT_COUNT" type="INT32">
      <short_desc>VTOL number of engines</short_desc>
Don Gagne's avatar
Don Gagne committed
3451
      <min>0</min>
3452 3453 3454 3455 3456 3457 3458 3459 3460 3461 3462 3463 3464 3465 3466 3467 3468 3469 3470 3471 3472 3473
    </parameter>
    <parameter default="900" name="VT_IDLE_PWM_MC" type="INT32">
      <short_desc>Idle speed of VTOL when in multicopter mode</short_desc>
      <min>900</min>
    </parameter>
    <parameter default="10.0" name="VT_MC_ARSPD_MIN" type="FLOAT">
      <short_desc>Minimum airspeed in multicopter mode</short_desc>
      <long_desc>This is the minimum speed of the air flowing over the control surfaces.</long_desc>
      <min>0.0</min>
    </parameter>
    <parameter default="30.0" name="VT_MC_ARSPD_MAX" type="FLOAT">
      <short_desc>Maximum airspeed in multicopter mode</short_desc>
      <long_desc>This is the maximum speed of the air flowing over the control surfaces.</long_desc>
      <min>0.0</min>
    </parameter>
    <parameter default="10.0" name="VT_MC_ARSPD_TRIM" type="FLOAT">
      <short_desc>Trim airspeed when in multicopter mode</short_desc>
      <long_desc>This is the airflow over the control surfaces for which no airspeed scaling is applied in multicopter mode.</long_desc>
      <min>0.0</min>
    </parameter>
    <parameter default="0" name="VT_FW_PERM_STAB" type="INT32">
      <short_desc>Permanent stabilization in fw mode</short_desc>
Don Gagne's avatar
Don Gagne committed
3474
      <long_desc>If set to one this parameter will cause permanent attitude stabilization in fw mode. This parameter has been introduced for pure convenience sake.</long_desc>
3475 3476 3477 3478 3479 3480 3481 3482 3483 3484 3485
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0.0" name="VT_FW_PITCH_TRIM" type="FLOAT">
      <short_desc>Fixed wing pitch trim</short_desc>
      <long_desc>This parameter allows to adjust the neutral elevon position in fixed wing mode.</long_desc>
      <min>-1</min>
      <max>1</max>
    </parameter>
    <parameter default="120.0" name="VT_POWER_MAX" type="FLOAT">
      <short_desc>Motor max power</short_desc>
Don Gagne's avatar
Don Gagne committed
3486
      <long_desc>Indicates the maximum power the motor is able to produce. Used to calculate propeller efficiency map.</long_desc>
3487 3488 3489 3490 3491
      <min>1</min>
    </parameter>
    <parameter default="0.0" name="VT_PROP_EFF" type="FLOAT">
      <short_desc>Propeller efficiency parameter</short_desc>
      <long_desc>Influences propeller efficiency at different power settings. Should be tuned beforehand.</long_desc>
Don Gagne's avatar
Don Gagne committed
3492
      <min>0.0</min>
3493 3494 3495 3496 3497 3498 3499 3500
      <max>0.9</max>
    </parameter>
    <parameter default="0.3" name="VT_ARSP_LP_GAIN" type="FLOAT">
      <short_desc>Total airspeed estimate low-pass filter gain</short_desc>
      <long_desc>Gain for tuning the low-pass filter for the total airspeed estimate</long_desc>
      <min>0.0</min>
      <max>0.99</max>
    </parameter>
Don Gagne's avatar
Don Gagne committed
3501 3502 3503 3504 3505 3506 3507 3508 3509 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3525 3526 3527 3528 3529 3530 3531 3532 3533 3534 3535
    <parameter default="0" name="VT_TYPE" type="INT32">
      <short_desc>VTOL Type (Tailsitter=0, Tiltrotor=1, Standard=2)</short_desc>
      <min>0</min>
      <max>2</max>
    </parameter>
    <parameter default="0" name="VT_ELEV_MC_LOCK" type="INT32">
      <short_desc>Lock elevons in multicopter mode</short_desc>
      <long_desc>If set to 1 the elevons are locked in multicopter mode</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="3.0" name="VT_F_TRANS_DUR" type="FLOAT">
      <short_desc>Duration of a front transition</short_desc>
      <long_desc>Time in seconds used for a transition</long_desc>
      <min>0.0</min>
      <max>5</max>
    </parameter>
    <parameter default="2.0" name="VT_B_TRANS_DUR" type="FLOAT">
      <short_desc>Duration of a back transition</short_desc>
      <long_desc>Time in seconds used for a back transition</long_desc>
      <min>0.0</min>
      <max>5</max>
    </parameter>
    <parameter default="8.0" name="VT_ARSP_BLEND" type="FLOAT">
      <short_desc>Transition blending airspeed</short_desc>
      <long_desc>Airspeed at which we can start blending both fw and mc controls. Set to 0 to disable.</long_desc>
      <min>0.0</min>
      <max>20.0</max>
    </parameter>
    <parameter default="10.0" name="VT_ARSP_TRANS" type="FLOAT">
      <short_desc>Transition airspeed</short_desc>
      <long_desc>Airspeed at which we can switch to fw mode</long_desc>
      <min>1.0</min>
      <max>20</max>
    </parameter>
3536 3537 3538 3539 3540 3541 3542 3543 3544 3545 3546 3547 3548 3549 3550 3551 3552 3553 3554 3555 3556 3557 3558 3559 3560 3561 3562 3563 3564 3565 3566 3567 3568 3569 3570 3571 3572 3573 3574 3575 3576 3577 3578 3579 3580 3581 3582 3583 3584 3585 3586 3587 3588 3589 3590 3591 3592 3593 3594 3595 3596 3597 3598 3599 3600 3601 3602 3603 3604 3605 3606 3607 3608 3609 3610 3611 3612 3613 3614 3615 3616 3617 3618 3619 3620 3621 3622 3623 3624 3625 3626 3627 3628 3629 3630 3631 3632 3633 3634 3635 3636 3637 3638 3639 3640 3641 3642 3643 3644 3645 3646 3647 3648 3649 3650 3651 3652 3653 3654 3655 3656 3657 3658 3659 3660 3661 3662 3663 3664 3665 3666 3667 3668 3669 3670 3671 3672 3673 3674 3675 3676 3677 3678 3679 3680 3681 3682 3683 3684 3685 3686 3687 3688 3689 3690 3691 3692 3693 3694 3695 3696 3697 3698 3699 3700 3701 3702 3703 3704 3705 3706 3707 3708 3709 3710 3711 3712 3713 3714 3715 3716 3717 3718 3719 3720 3721 3722 3723 3724 3725 3726 3727 3728 3729 3730 3731 3732 3733 3734 3735 3736 3737 3738 3739 3740 3741 3742 3743 3744 3745 3746 3747 3748 3749 3750 3751
  </group>
  <group name="mTECS">
    <parameter default="0" name="MT_ENABLED" type="INT32">
      <short_desc>mTECS enabled</short_desc>
      <long_desc>Set to 1 to enable mTECS</long_desc>
      <min>0</min>
      <max>1</max>
    </parameter>
    <parameter default="0.7" name="MT_THR_FF" type="FLOAT">
      <short_desc>Total Energy Rate Control Feedforward
Maps the total energy rate setpoint to the throttle setpoint</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.1" name="MT_THR_P" type="FLOAT">
      <short_desc>Total Energy Rate Control P
Maps the total energy rate error to the throttle setpoint</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.25" name="MT_THR_I" type="FLOAT">
      <short_desc>Total Energy Rate Control I
Maps the integrated total energy rate to the throttle setpoint</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.7" name="MT_THR_OFF" type="FLOAT">
      <short_desc>Total Energy Rate Control Offset (Cruise throttle sp)</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.4" name="MT_PIT_FF" type="FLOAT">
      <short_desc>Energy Distribution Rate Control Feedforward
Maps the energy distribution rate setpoint to the pitch setpoint</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.03" name="MT_PIT_P" type="FLOAT">
      <short_desc>Energy Distribution Rate Control P
Maps the energy distribution rate error to the pitch setpoint</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.03" name="MT_PIT_I" type="FLOAT">
      <short_desc>Energy Distribution Rate Control I
Maps the integrated energy distribution rate error to the pitch setpoint</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.0" name="MT_PIT_OFF" type="FLOAT">
      <short_desc>Total Energy Distribution Offset (Cruise pitch sp)</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.0" name="MT_THR_MIN" type="FLOAT">
      <short_desc>Minimal Throttle Setpoint</short_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="1.0" name="MT_THR_MAX" type="FLOAT">
      <short_desc>Maximal Throttle Setpoint</short_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="-45.0" name="MT_PIT_MIN" type="FLOAT">
      <short_desc>Minimal Pitch Setpoint in Degrees</short_desc>
      <min>-90.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="20.0" name="MT_PIT_MAX" type="FLOAT">
      <short_desc>Maximal Pitch Setpoint in Degrees</short_desc>
      <min>-90.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="1.0" name="MT_ALT_LP" type="FLOAT">
      <short_desc>Lowpass (cutoff freq.) for altitude</short_desc>
    </parameter>
    <parameter default="1.0" name="MT_FPA_LP" type="FLOAT">
      <short_desc>Lowpass (cutoff freq.) for the flight path angle</short_desc>
    </parameter>
    <parameter default="0.3" name="MT_FPA_P" type="FLOAT">
      <short_desc>P gain for the altitude control
Maps the altitude error to the flight path angle setpoint</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.0" name="MT_FPA_D" type="FLOAT">
      <short_desc>D gain for the altitude control
Maps the change of altitude error to the flight path angle setpoint</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="1.0" name="MT_FPA_D_LP" type="FLOAT">
      <short_desc>Lowpass for FPA error derivative calculation (see MT_FPA_D)</short_desc>
    </parameter>
    <parameter default="-20.0" name="MT_FPA_MIN" type="FLOAT">
      <short_desc>Minimal flight path angle setpoint</short_desc>
      <min>-90.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="30.0" name="MT_FPA_MAX" type="FLOAT">
      <short_desc>Maximal flight path angle setpoint</short_desc>
      <min>-90.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="0.5" name="MT_A_LP" type="FLOAT">
      <short_desc>Lowpass (cutoff freq.) for airspeed</short_desc>
    </parameter>
    <parameter default="0.5" name="MT_AD_LP" type="FLOAT">
      <short_desc>Airspeed derivative calculation lowpass</short_desc>
    </parameter>
    <parameter default="0.3" name="MT_ACC_P" type="FLOAT">
      <short_desc>P gain for the airspeed control
Maps the airspeed error to the acceleration setpoint</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.0" name="MT_ACC_D" type="FLOAT">
      <short_desc>D gain for the airspeed control
Maps the change of airspeed error to the acceleration setpoint</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="0.5" name="MT_ACC_D_LP" type="FLOAT">
      <short_desc>Lowpass for ACC error derivative calculation (see MT_ACC_D)</short_desc>
    </parameter>
    <parameter default="-40.0" name="MT_ACC_MIN" type="FLOAT">
      <short_desc>Minimal acceleration (air)</short_desc>
      <unit>m/s^2</unit>
    </parameter>
    <parameter default="40.0" name="MT_ACC_MAX" type="FLOAT">
      <short_desc>Maximal acceleration (air)</short_desc>
      <unit>m/s^2</unit>
    </parameter>
    <parameter default="1.0" name="MT_TKF_THR_MIN" type="FLOAT">
      <short_desc>Minimal throttle during takeoff</short_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="1.0" name="MT_TKF_THR_MAX" type="FLOAT">
      <short_desc>Maximal throttle during takeoff</short_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="0.0" name="MT_TKF_PIT_MIN" type="FLOAT">
      <short_desc>Minimal pitch during takeoff</short_desc>
      <min>-90.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="45.0" name="MT_TKF_PIT_MAX" type="FLOAT">
      <short_desc>Maximal pitch during takeoff</short_desc>
      <min>-90.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="1.0" name="MT_USP_THR_MIN" type="FLOAT">
      <short_desc>Minimal throttle in underspeed mode</short_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="1.0" name="MT_USP_THR_MAX" type="FLOAT">
      <short_desc>Maximal throttle in underspeed mode</short_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="-45.0" name="MT_USP_PIT_MIN" type="FLOAT">
      <short_desc>Minimal pitch in underspeed mode</short_desc>
      <min>-90.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="0.0" name="MT_USP_PIT_MAX" type="FLOAT">
      <short_desc>Maximal pitch in underspeed mode</short_desc>
      <min>-90.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="0.0" name="MT_LND_THR_MIN" type="FLOAT">
      <short_desc>Minimal throttle in landing mode (only last phase of landing)</short_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="0.0" name="MT_LND_THR_MAX" type="FLOAT">
      <short_desc>Maximal throttle in landing mode (only last phase of landing)</short_desc>
      <min>0.0</min>
      <max>1.0</max>
    </parameter>
    <parameter default="-5.0" name="MT_LND_PIT_MIN" type="FLOAT">
      <short_desc>Minimal pitch in landing mode</short_desc>
      <min>-90.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="15.0" name="MT_LND_PIT_MAX" type="FLOAT">
      <short_desc>Maximal pitch in landing mode</short_desc>
      <min>-90.0</min>
      <max>90.0</max>
      <unit>deg</unit>
    </parameter>
    <parameter default="10.0" name="MT_THR_I_MAX" type="FLOAT">
      <short_desc>Integrator Limit for Total Energy Rate Control</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
    <parameter default="10.0" name="MT_PIT_I_MAX" type="FLOAT">
      <short_desc>Integrator Limit for Energy Distribution Rate Control</short_desc>
      <min>0.0</min>
      <max>10.0</max>
    </parameter>
  </group>
  <group name="Miscellaneous">
Don Gagne's avatar
Don Gagne committed
3752 3753 3754 3755 3756 3757
    <parameter default="15" name="LED_RGB_MAXBRT" type="INT32">
      <short_desc>RGB Led brightness limit</short_desc>
      <long_desc>Set to 0 to disable, 1 for minimum brightness up to 15 (max)</long_desc>
      <min>0</min>
      <max>15</max>
    </parameter>
3758 3759 3760 3761 3762 3763 3764 3765 3766
    <parameter default="0.1" name="EXFW_HDNG_P" type="FLOAT">
      <short_desc>EXFW_HDNG_P</short_desc>
    </parameter>
    <parameter default="0.2" name="EXFW_ROLL_P" type="FLOAT">
      <short_desc>EXFW_ROLL_P</short_desc>
    </parameter>
    <parameter default="0.2" name="EXFW_PITCH_P" type="FLOAT">
      <short_desc>EXFW_PITCH_P</short_desc>
    </parameter>
Don Gagne's avatar
Don Gagne committed
3767 3768 3769 3770 3771 3772 3773 3774
    <parameter default="0.1" name="RV_YAW_P" type="FLOAT">
      <short_desc>RV_YAW_P</short_desc>
    </parameter>
    <parameter default="-1.0" name="TEST_MIN" type="FLOAT">
      <short_desc>TEST_MIN</short_desc>
    </parameter>
    <parameter default="1.0" name="TEST_MAX" type="FLOAT">
      <short_desc>TEST_MAX</short_desc>
3775
    </parameter>
Don Gagne's avatar
Don Gagne committed
3776 3777
    <parameter default="0.5" name="TEST_TRIM" type="FLOAT">
      <short_desc>TEST_TRIM</short_desc>
3778
    </parameter>
Don Gagne's avatar
Don Gagne committed
3779 3780
    <parameter default="10.0" name="TEST_HP" type="FLOAT">
      <short_desc>TEST_HP</short_desc>
3781
    </parameter>
Don Gagne's avatar
Don Gagne committed
3782 3783
    <parameter default="10.0" name="TEST_LP" type="FLOAT">
      <short_desc>TEST_LP</short_desc>
3784
    </parameter>
Don Gagne's avatar
Don Gagne committed
3785 3786
    <parameter default="0.2" name="TEST_P" type="FLOAT">
      <short_desc>TEST_P</short_desc>
3787
    </parameter>
Don Gagne's avatar
Don Gagne committed
3788 3789
    <parameter default="0.1" name="TEST_I" type="FLOAT">
      <short_desc>TEST_I</short_desc>
3790
    </parameter>
Don Gagne's avatar
Don Gagne committed
3791 3792 3793 3794 3795 3796 3797 3798 3799 3800 3801 3802 3803 3804
    <parameter default="1.0" name="TEST_I_MAX" type="FLOAT">
      <short_desc>TEST_I_MAX</short_desc>
    </parameter>
    <parameter default="0.01" name="TEST_D" type="FLOAT">
      <short_desc>TEST_D</short_desc>
    </parameter>
    <parameter default="10.0" name="TEST_D_LP" type="FLOAT">
      <short_desc>TEST_D_LP</short_desc>
    </parameter>
    <parameter default="1.0" name="TEST_MEAN" type="FLOAT">
      <short_desc>TEST_MEAN</short_desc>
    </parameter>
    <parameter default="2.0" name="TEST_DEV" type="FLOAT">
      <short_desc>TEST_DEV</short_desc>
3805 3806 3807 3808 3809 3810 3811 3812 3813 3814 3815 3816 3817 3818 3819 3820 3821 3822 3823 3824 3825 3826 3827 3828 3829 3830 3831 3832 3833 3834 3835 3836 3837 3838 3839 3840 3841 3842 3843 3844 3845 3846 3847 3848 3849 3850 3851 3852 3853 3854 3855 3856 3857 3858 3859 3860 3861 3862 3863 3864 3865 3866 3867 3868 3869 3870 3871 3872 3873 3874 3875 3876 3877 3878 3879 3880 3881 3882 3883 3884 3885 3886 3887 3888 3889 3890 3891 3892 3893 3894 3895 3896 3897 3898 3899 3900 3901 3902 3903 3904 3905 3906 3907 3908 3909 3910 3911 3912 3913 3914 3915 3916 3917 3918 3919 3920 3921 3922 3923 3924 3925
    </parameter>
    <parameter default="300.0" name="FWB_P_LP" type="FLOAT">
      <short_desc>FWB_P_LP</short_desc>
    </parameter>
    <parameter default="300.0" name="FWB_Q_LP" type="FLOAT">
      <short_desc>FWB_Q_LP</short_desc>
    </parameter>
    <parameter default="300.0" name="FWB_R_LP" type="FLOAT">
      <short_desc>FWB_R_LP</short_desc>
    </parameter>
    <parameter default="1.0" name="FWB_R_HP" type="FLOAT">
      <short_desc>FWB_R_HP</short_desc>
    </parameter>
    <parameter default="0.3" name="FWB_P2AIL" type="FLOAT">
      <short_desc>FWB_P2AIL</short_desc>
    </parameter>
    <parameter default="0.1" name="FWB_Q2ELV" type="FLOAT">
      <short_desc>FWB_Q2ELV</short_desc>
    </parameter>
    <parameter default="0.1" name="FWB_R2RDR" type="FLOAT">
      <short_desc>FWB_R2RDR</short_desc>
    </parameter>
    <parameter default="0.5" name="FWB_PSI2PHI" type="FLOAT">
      <short_desc>FWB_PSI2PHI</short_desc>
    </parameter>
    <parameter default="1.0" name="FWB_PHI2P" type="FLOAT">
      <short_desc>FWB_PHI2P</short_desc>
    </parameter>
    <parameter default="0.3" name="FWB_PHI_LIM_MAX" type="FLOAT">
      <short_desc>FWB_PHI_LIM_MAX</short_desc>
    </parameter>
    <parameter default="1.0" name="FWB_V2THE_P" type="FLOAT">
      <short_desc>FWB_V2THE_P</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_V2THE_I" type="FLOAT">
      <short_desc>FWB_V2THE_I</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_V2THE_D" type="FLOAT">
      <short_desc>FWB_V2THE_D</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_V2THE_D_LP" type="FLOAT">
      <short_desc>FWB_V2THE_D_LP</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_V2THE_I_MAX" type="FLOAT">
      <short_desc>FWB_V2THE_I_MAX</short_desc>
    </parameter>
    <parameter default="-0.5" name="FWB_THE_MIN" type="FLOAT">
      <short_desc>FWB_THE_MIN</short_desc>
    </parameter>
    <parameter default="0.5" name="FWB_THE_MAX" type="FLOAT">
      <short_desc>FWB_THE_MAX</short_desc>
    </parameter>
    <parameter default="1.0" name="FWB_THE2Q_P" type="FLOAT">
      <short_desc>FWB_THE2Q_P</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_THE2Q_I" type="FLOAT">
      <short_desc>FWB_THE2Q_I</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_THE2Q_D" type="FLOAT">
      <short_desc>FWB_THE2Q_D</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_THE2Q_D_LP" type="FLOAT">
      <short_desc>FWB_THE2Q_D_LP</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_THE2Q_I_MAX" type="FLOAT">
      <short_desc>FWB_THE2Q_I_MAX</short_desc>
    </parameter>
    <parameter default="0.01" name="FWB_H2THR_P" type="FLOAT">
      <short_desc>FWB_H2THR_P</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_H2THR_I" type="FLOAT">
      <short_desc>FWB_H2THR_I</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_H2THR_D" type="FLOAT">
      <short_desc>FWB_H2THR_D</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_H2THR_D_LP" type="FLOAT">
      <short_desc>FWB_H2THR_D_LP</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_H2THR_I_MAX" type="FLOAT">
      <short_desc>FWB_H2THR_I_MAX</short_desc>
    </parameter>
    <parameter default="1.57" name="FWB_XT2YAW_MAX" type="FLOAT">
      <short_desc>FWB_XT2YAW_MAX</short_desc>
    </parameter>
    <parameter default="0.005" name="FWB_XT2YAW" type="FLOAT">
      <short_desc>FWB_XT2YAW</short_desc>
    </parameter>
    <parameter default="10.0" name="FWB_V_MIN" type="FLOAT">
      <short_desc>FWB_V_MIN</short_desc>
    </parameter>
    <parameter default="12.0" name="FWB_V_CMD" type="FLOAT">
      <short_desc>FWB_V_CMD</short_desc>
    </parameter>
    <parameter default="16.0" name="FWB_V_MAX" type="FLOAT">
      <short_desc>FWB_V_MAX</short_desc>
    </parameter>
    <parameter default="1.0" name="FWB_CR_MAX" type="FLOAT">
      <short_desc>FWB_CR_MAX</short_desc>
    </parameter>
    <parameter default="0.01" name="FWB_CR2THR_P" type="FLOAT">
      <short_desc>FWB_CR2THR_P</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_CR2THR_I" type="FLOAT">
      <short_desc>FWB_CR2THR_I</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_CR2THR_D" type="FLOAT">
      <short_desc>FWB_CR2THR_D</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_CR2THR_D_LP" type="FLOAT">
      <short_desc>FWB_CR2THR_D_LP</short_desc>
    </parameter>
    <parameter default="0.0" name="FWB_CR2THR_I_MAX" type="FLOAT">
      <short_desc>FWB_CR2THR_I_MAX</short_desc>
    </parameter>
    <parameter default="0.8" name="FWB_TRIM_THR" type="FLOAT">
      <short_desc>FWB_TRIM_THR</short_desc>
    </parameter>
    <parameter default="12.0" name="FWB_TRIM_V" type="FLOAT">
      <short_desc>FWB_TRIM_V</short_desc>
    </parameter>
Don Gagne's avatar
Don Gagne committed
3926 3927 3928 3929 3930 3931 3932 3933
    <parameter default="2.5" name="FW_FLARE_PMIN" type="FLOAT">
      <short_desc>Flare, minimum pitch</short_desc>
      <long_desc>Minimum pitch during flare, a positive sign means nose up Applied once FW_LND_TLALT is reached</long_desc>
    </parameter>
    <parameter default="15.0" name="FW_FLARE_PMAX" type="FLOAT">
      <short_desc>Flare, maximum pitch</short_desc>
      <long_desc>Maximum pitch during flare, a positive sign means nose up Applied once FW_LND_TLALT is reached</long_desc>
    </parameter>
3934 3935 3936 3937 3938 3939 3940 3941 3942 3943 3944 3945 3946 3947
    <parameter default="10.0" name="SEG_TH2V_P" type="FLOAT">
      <short_desc>SEG_TH2V_P</short_desc>
    </parameter>
    <parameter default="0.0" name="SEG_TH2V_I" type="FLOAT">
      <short_desc>SEG_TH2V_I</short_desc>
    </parameter>
    <parameter default="0.0" name="SEG_TH2V_I_MAX" type="FLOAT">
      <short_desc>SEG_TH2V_I_MAX</short_desc>
    </parameter>
    <parameter default="1.0" name="SEG_Q2V" type="FLOAT">
      <short_desc>SEG_Q2V</short_desc>
    </parameter>
    <parameter default="0" name="RC_MAP_FAILSAFE" type="INT32">
      <short_desc>Failsafe channel mapping</short_desc>
Don Gagne's avatar
Don Gagne committed
3948
      <long_desc>The RC mapping index indicates which channel is used for failsafe If 0, whichever channel is mapped to throttle is used otherwise the value indicates the specific rc channel to use</long_desc>
3949 3950 3951 3952
      <min>0</min>
      <max>18</max>
    </parameter>
  </group>
3953
</parameters>