ParameterFactMetaData.xml 135 KB
Newer Older
Don Gagne's avatar
Don Gagne committed
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161
<?xml version="1.0" ?>
<parameters>
    <group name="Battery Calibration">
        <parameter name="BAT_V_EMPTY" type="FLOAT">
            <short_desc>Empty cell voltage</short_desc>
            <long_desc>Defines the voltage where a single cell of the battery is considered empty.</long_desc>
            <default>3.4</default>
        </parameter>
        <parameter name="BAT_V_CHARGED" type="FLOAT">
            <short_desc>Full cell voltage</short_desc>
            <long_desc>Defines the voltage where a single cell of the battery is considered full.</long_desc>
            <default>4.2</default>
        </parameter>
        <parameter name="BAT_V_LOAD_DROP" type="FLOAT">
            <short_desc>Voltage drop per cell on 100% load</short_desc>
            <long_desc>This implicitely defines the internal resistance
                to maximum current ratio and assumes linearity.</long_desc>
            <default>0.07</default>
        </parameter>
        <parameter name="BAT_N_CELLS" type="INT32">
            <short_desc>Number of cells</short_desc>
            <long_desc>Defines the number of cells the attached battery consists of.</long_desc>
            <default>3</default>
        </parameter>
        <parameter name="BAT_CAPACITY" type="FLOAT">
            <short_desc>Battery capacity</short_desc>
            <long_desc>Defines the capacity of the attached battery.</long_desc>
            <default>-1.0</default>
        </parameter>
        <parameter name="BAT_V_SCALE_IO" type="INT32">
            <short_desc>Scaling factor for battery voltage sensor on PX4IO</short_desc>
            <default>10000</default>
        </parameter>
        <parameter name="BAT_V_SCALING" type="FLOAT">
            <short_desc>Scaling factor for battery voltage sensor on FMU v2</short_desc>
            <default>0.0082</default>
        </parameter>
        <parameter name="BAT_V_SCALING" type="FLOAT">
            <short_desc>Scaling factor for battery voltage sensor on AeroCore</short_desc>
            <long_desc>For R70 = 133K, R71 = 10K --&gt; scale = 1.8 * 143 / (4096*10) = 0.0063</long_desc>
            <default>0.0063</default>
        </parameter>
        <parameter name="BAT_V_SCALING" type="FLOAT">
            <short_desc>Scaling factor for battery voltage sensor on FMU v1</short_desc>
            <long_desc>FMUv1 standalone: 1/(10 / (47+10)) * (3.3 / 4095) = 0.00459340659
                FMUv1 with PX4IO: 0.00459340659
                FMUv1 with PX4IOAR: (3.3f * 52.0f / 5.0f / 4095.0f) = 0.00838095238</long_desc>
            <default>0.00459340659</default>
        </parameter>
        <parameter name="BAT_C_SCALING" type="FLOAT">
            <short_desc>Scaling factor for battery current sensor</short_desc>
            <default>0.0124</default>
        </parameter>
    </group>
    <group name="Circuit Breaker">
        <parameter name="CBRK_SUPPLY_CHK" type="INT32">
            <short_desc>Circuit breaker for power supply check</short_desc>
            <long_desc>Setting this parameter to 894281 will disable the power valid
                checks in the commander.
                WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
            <default>0</default>
            <min>0</min>
            <max>894281</max>
        </parameter>
        <parameter name="CBRK_RATE_CTRL" type="INT32">
            <short_desc>Circuit breaker for rate controller output</short_desc>
            <long_desc>Setting this parameter to 140253 will disable the rate
                controller uORB publication.
                WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
            <default>0</default>
            <min>0</min>
            <max>140253</max>
        </parameter>
        <parameter name="CBRK_IO_SAFETY" type="INT32">
            <short_desc>Circuit breaker for IO safety</short_desc>
            <long_desc>Setting this parameter to 894281 will disable IO safety.
                WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
            <default>0</default>
            <min>0</min>
            <max>22027</max>
        </parameter>
        <parameter name="CBRK_AIRSPD_CHK" type="INT32">
            <short_desc>Circuit breaker for airspeed sensor</short_desc>
            <long_desc>Setting this parameter to 162128 will disable the check for an airspeed sensor.
                WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
            <default>0</default>
            <min>0</min>
            <max>162128</max>
        </parameter>
        <parameter name="CBRK_FLIGHTTERM" type="INT32">
            <short_desc>Circuit breaker for flight termination</short_desc>
            <long_desc>Setting this parameter to 121212 will disable the flight termination action.
                --&gt; The IO driver will not do flight termination if requested by the FMU
                WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
            <default>121212</default>
            <min>0</min>
            <max>121212</max>
        </parameter>
        <parameter name="CBRK_ENGINEFAIL" type="INT32">
            <short_desc>Circuit breaker for engine failure detection</short_desc>
            <long_desc>Setting this parameter to 284953 will disable the engine failure detection.
                If the aircraft is in engine failure mode the enine failure flag will be
                set to healthy
                WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
            <default>284953</default>
            <min>0</min>
            <max>284953</max>
        </parameter>
        <parameter name="CBRK_GPSFAIL" type="INT32">
            <short_desc>Circuit breaker for gps failure detection</short_desc>
            <long_desc>Setting this parameter to 240024 will disable the gps failure detection.
                If the aircraft is in gps failure mode the gps failure flag will be
                set to healthy
                WARNING: ENABLING THIS CIRCUIT BREAKER IS AT OWN RISK</long_desc>
            <default>240024</default>
            <min>0</min>
            <max>240024</max>
        </parameter>
    </group>
    <group name="DLL">
        <parameter name="NAV_DLL_CH_T" type="FLOAT">
            <short_desc>Comms hold wait time</short_desc>
            <long_desc>The amount of time in seconds the system should wait at the comms hold waypoint</long_desc>
            <default>120.0</default>
            <min>0.0</min>
            <unit>seconds</unit>
        </parameter>
        <parameter name="NAV_DLL_CH_LAT" type="INT32">
            <short_desc>Comms hold Lat</short_desc>
            <long_desc>Latitude of comms hold waypoint</long_desc>
            <default>-266072120</default>
            <min>0</min>
            <unit>degrees * 1e7</unit>
        </parameter>
        <parameter name="NAV_DLL_CH_LON" type="INT32">
            <short_desc>Comms hold Lon</short_desc>
            <long_desc>Longitude of comms hold waypoint</long_desc>
            <default>1518453890</default>
            <min>0</min>
            <unit>degrees * 1e7</unit>
        </parameter>
        <parameter name="NAV_DLL_CH_ALT" type="FLOAT">
            <short_desc>Comms hold alt</short_desc>
            <long_desc>Altitude of comms hold waypoint</long_desc>
            <default>600.0</default>
            <min>0.0</min>
            <unit>m</unit>
        </parameter>
        <parameter name="NAV_DLL_AH_T" type="FLOAT">
            <short_desc>Aifield hole wait time</short_desc>
            <long_desc>The amount of time in seconds the system should wait at the airfield home waypoint</long_desc>
            <default>120.0</default>
            <min>0.0</min>
            <unit>seconds</unit>
        </parameter>
        <parameter name="NAV_DLL_N" type="INT32">
            <short_desc>Number of allowed Datalink timeouts</short_desc>
            <long_desc>After more than this number of data link timeouts the aircraft returns home directly</long_desc>
            <default>2</default>
            <min>0</min>
            <max>1000</max>
162
            <unit>timeouts</unit>
Don Gagne's avatar
Don Gagne committed
163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129 1130 1131 1132 1133 1134 1135 1136 1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1165 1166 1167 1168 1169 1170 1171 1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210 1211 1212 1213 1214 1215 1216 1217 1218 1219 1220 1221 1222 1223 1224 1225 1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246 1247 1248 1249 1250 1251 1252 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272 1273 1274 1275 1276 1277 1278 1279 1280 1281 1282 1283 1284 1285 1286 1287 1288 1289 1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 1314 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345 1346 1347 1348 1349 1350 1351 1352 1353 1354 1355 1356 1357 1358 1359 1360 1361 1362 1363 1364 1365 1366 1367 1368 1369 1370 1371 1372 1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1385 1386 1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397 1398 1399 1400 1401 1402 1403 1404 1405 1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440 1441 1442 1443 1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456 1457 1458 1459 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492 1493 1494 1495 1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1514 1515 1516 1517 1518 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 1541 1542 1543 1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561 1562 1563 1564 1565 1566 1567 1568 1569 1570 1571 1572 1573 1574 1575 1576 1577 1578 1579 1580 1581 1582 1583 1584 1585 1586 1587 1588 1589 1590 1591 1592 1593 1594 1595 1596 1597 1598 1599 1600 1601 1602 1603 1604 1605 1606 1607 1608 1609 1610 1611 1612 1613 1614 1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625 1626 1627 1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651 1652 1653 1654 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686 1687 1688 1689 1690 1691 1692 1693 1694 1695 1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 1739 1740 1741 1742 1743 1744 1745 1746 1747 1748 1749 1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760 1761 1762 1763 1764 1765 1766 1767 1768 1769 1770 1771 1772 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782 1783 1784 1785 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797 1798 1799 1800 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1820 1821 1822 1823 1824 1825 1826 1827 1828 1829 1830 1831 1832 1833 1834 1835 1836 1837 1838 1839 1840 1841 1842 1843 1844 1845 1846 1847 1848 1849 1850 1851 1852 1853 1854 1855 1856 1857 1858 1859 1860 1861 1862 1863 1864 1865 1866 1867 1868 1869 1870 1871 1872 1873 1874 1875 1876 1877 1878 1879 1880 1881 1882 1883 1884 1885 1886 1887 1888 1889 1890 1891 1892 1893 1894 1895 1896 1897 1898 1899 1900 1901 1902 1903 1904 1905 1906 1907 1908 1909 1910 1911 1912 1913 1914 1915 1916 1917 1918 1919 1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931 1932 1933 1934 1935 1936 1937 1938 1939 1940 1941 1942 1943 1944 1945 1946 1947 1948 1949 1950 1951 1952 1953 1954 1955 1956 1957 1958 1959 1960 1961 1962 1963 1964 1965 1966 1967 1968 1969 1970 1971 1972 1973 1974 1975 1976 1977 1978 1979 1980 1981 1982 1983 1984 1985 1986 1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 2031 2032 2033 2034 2035 2036 2037 2038 2039 2040 2041 2042 2043 2044
        </parameter>
        <parameter name="NAV_DLL_CHSK" type="INT32">
            <short_desc>Skip comms hold wp</short_desc>
            <long_desc>If set to 1 the system will skip the comms hold wp on data link loss and will directly fly to
                airfield home</long_desc>
            <default>0</default>
            <min>0</min>
            <max>1</max>
        </parameter>
        <parameter name="NAV_AH_LAT" type="INT32">
            <short_desc>Airfield home Lat</short_desc>
            <long_desc>Latitude of airfield home waypoint</long_desc>
            <default>-265847810</default>
            <min>0</min>
            <unit>degrees * 1e7</unit>
        </parameter>
        <parameter name="NAV_AH_LON" type="INT32">
            <short_desc>Airfield home Lon</short_desc>
            <long_desc>Longitude of airfield home waypoint</long_desc>
            <default>1518423250</default>
            <min>0</min>
            <unit>degrees * 1e7</unit>
        </parameter>
        <parameter name="NAV_AH_ALT" type="FLOAT">
            <short_desc>Airfield home alt</short_desc>
            <long_desc>Altitude of airfield home waypoint</long_desc>
            <default>600.0</default>
            <min>0.0</min>
            <unit>m</unit>
        </parameter>
    </group>
    <group name="FW Attitude Control">
        <parameter name="FW_ATT_TC" type="FLOAT">
            <short_desc>Attitude Time Constant</short_desc>
            <long_desc>This defines the latency between a step input and the achieved setpoint
                (inverse to a P gain). Half a second is a good start value and fits for
                most average systems. Smaller systems may require smaller values, but as
                this will wear out servos faster, the value should only be decreased as
                needed.</long_desc>
            <default>0.5</default>
            <min>0.4</min>
            <max>1.0</max>
            <unit>seconds</unit>
        </parameter>
        <parameter name="FW_PR_P" type="FLOAT">
            <short_desc>Pitch rate proportional gain</short_desc>
            <long_desc>This defines how much the elevator input will be commanded depending on the
                current body angular rate error.</long_desc>
            <default>0.05</default>
        </parameter>
        <parameter name="FW_PR_I" type="FLOAT">
            <short_desc>Pitch rate integrator gain</short_desc>
            <long_desc>This gain defines how much control response will result out of a steady
                state error. It trims any constant error.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>50.0</max>
        </parameter>
        <parameter name="FW_P_RMAX_POS" type="FLOAT">
            <short_desc>Maximum positive / up pitch rate</short_desc>
            <long_desc>This limits the maximum pitch up angular rate the controller will output (in
                degrees per second). Setting a value of zero disables the limit.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>90.0</max>
            <unit>deg/s</unit>
        </parameter>
        <parameter name="FW_P_RMAX_NEG" type="FLOAT">
            <short_desc>Maximum negative / down pitch rate</short_desc>
            <long_desc>This limits the maximum pitch down up angular rate the controller will
                output (in degrees per second). Setting a value of zero disables the limit.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>90.0</max>
            <unit>deg/s</unit>
        </parameter>
        <parameter name="FW_PR_IMAX" type="FLOAT">
            <short_desc>Pitch rate integrator limit</short_desc>
            <long_desc>The portion of the integrator part in the control surface deflection is
                limited to this value</long_desc>
            <default>0.2</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="FW_P_ROLLFF" type="FLOAT">
            <short_desc>Roll to Pitch feedforward gain</short_desc>
            <long_desc>This compensates during turns and ensures the nose stays level.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>2.0</max>
        </parameter>
        <parameter name="FW_RR_P" type="FLOAT">
            <short_desc>Roll rate proportional Gain</short_desc>
            <long_desc>This defines how much the aileron input will be commanded depending on the
                current body angular rate error.</long_desc>
            <default>0.05</default>
        </parameter>
        <parameter name="FW_RR_I" type="FLOAT">
            <short_desc>Roll rate integrator Gain</short_desc>
            <long_desc>This gain defines how much control response will result out of a steady
                state error. It trims any constant error.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>100.0</max>
        </parameter>
        <parameter name="FW_RR_IMAX" type="FLOAT">
            <short_desc>Roll Integrator Anti-Windup</short_desc>
            <long_desc>The portion of the integrator part in the control surface deflection is limited to this value.</long_desc>
            <default>0.2</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="FW_R_RMAX" type="FLOAT">
            <short_desc>Maximum Roll Rate</short_desc>
            <long_desc>This limits the maximum roll rate the controller will output (in degrees per
                second). Setting a value of zero disables the limit.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>90.0</max>
            <unit>deg/s</unit>
        </parameter>
        <parameter name="FW_YR_P" type="FLOAT">
            <short_desc>Yaw rate proportional gain</short_desc>
            <long_desc>This defines how much the rudder input will be commanded depending on the
                current body angular rate error.</long_desc>
            <default>0.05</default>
        </parameter>
        <parameter name="FW_YR_I" type="FLOAT">
            <short_desc>Yaw rate integrator gain</short_desc>
            <long_desc>This gain defines how much control response will result out of a steady
                state error. It trims any constant error.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>50.0</max>
        </parameter>
        <parameter name="FW_YR_IMAX" type="FLOAT">
            <short_desc>Yaw rate integrator limit</short_desc>
            <long_desc>The portion of the integrator part in the control surface deflection is
                limited to this value</long_desc>
            <default>0.2</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="FW_Y_RMAX" type="FLOAT">
            <short_desc>Maximum Yaw Rate</short_desc>
            <long_desc>This limits the maximum yaw rate the controller will output (in degrees per
                second). Setting a value of zero disables the limit.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>90.0</max>
            <unit>deg/s</unit>
        </parameter>
        <parameter name="FW_RR_FF" type="FLOAT">
            <short_desc>Roll rate feed forward</short_desc>
            <long_desc>Direct feed forward from rate setpoint to control surface output</long_desc>
            <default>0.3</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="FW_PR_FF" type="FLOAT">
            <short_desc>Pitch rate feed forward</short_desc>
            <long_desc>Direct feed forward from rate setpoint to control surface output</long_desc>
            <default>0.4</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="FW_YR_FF" type="FLOAT">
            <short_desc>Yaw rate feed forward</short_desc>
            <long_desc>Direct feed forward from rate setpoint to control surface output</long_desc>
            <default>0.3</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="FW_YCO_VMIN" type="FLOAT">
            <short_desc>Minimal speed for yaw coordination</short_desc>
            <long_desc>For airspeeds above this value, the yaw rate is calculated for a coordinated
                turn. Set to a very high value to disable.</long_desc>
            <default>1000.0</default>
            <unit>m/s</unit>
        </parameter>
        <parameter name="FW_AIRSPD_MIN" type="FLOAT">
            <short_desc>Minimum Airspeed</short_desc>
            <long_desc>If the airspeed falls below this value, the TECS controller will try to
                increase airspeed more aggressively.</long_desc>
            <default>13.0</default>
            <min>0.0</min>
            <max>30.0</max>
            <unit>m/s</unit>
        </parameter>
        <parameter name="FW_AIRSPD_TRIM" type="FLOAT">
            <short_desc>Trim Airspeed</short_desc>
            <long_desc>The TECS controller tries to fly at this airspeed.</long_desc>
            <default>20.0</default>
            <min>0.0</min>
            <max>30.0</max>
            <unit>m/s</unit>
        </parameter>
        <parameter name="FW_AIRSPD_MAX" type="FLOAT">
            <short_desc>Maximum Airspeed</short_desc>
            <long_desc>If the airspeed is above this value, the TECS controller will try to decrease
                airspeed more aggressively.</long_desc>
            <default>50.0</default>
            <min>0.0</min>
            <max>30.0</max>
            <unit>m/s</unit>
        </parameter>
        <parameter name="FW_RSP_OFF" type="FLOAT">
            <short_desc>Roll Setpoint Offset</short_desc>
            <long_desc>An airframe specific offset of the roll setpoint in degrees, the value is
                added to the roll setpoint and should correspond to the typical cruise speed
                of the airframe.</long_desc>
            <default>0.0</default>
            <min>-90.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="FW_PSP_OFF" type="FLOAT">
            <short_desc>Pitch Setpoint Offset</short_desc>
            <long_desc>An airframe specific offset of the pitch setpoint in degrees, the value is
                added to the pitch setpoint and should correspond to the typical cruise
                speed of the airframe.</long_desc>
            <default>0.0</default>
            <min>-90.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="FW_MAN_R_MAX" type="FLOAT">
            <short_desc>Max Manual Roll</short_desc>
            <long_desc>Max roll for manual control in attitude stabilized mode</long_desc>
            <default>45.0</default>
            <min>0.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="FW_MAN_P_MAX" type="FLOAT">
            <short_desc>Max Manual Pitch</short_desc>
            <long_desc>Max pitch for manual control in attitude stabilized mode</long_desc>
            <default>45.0</default>
            <min>0.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
    </group>
    <group name="Fixed Wing TECS">
        <parameter name="FW_T_SINK_MIN" type="FLOAT">
            <short_desc>Minimum descent rate</short_desc>
            <long_desc>This is the sink rate of the aircraft with the throttle
                set to THR_MIN and flown at the same airspeed as used
                to measure FW_T_CLMB_MAX.</long_desc>
            <default>2.0</default>
        </parameter>
        <parameter name="FW_T_SINK_MAX" type="FLOAT">
            <short_desc>Maximum descent rate</short_desc>
            <long_desc>This sets the maximum descent rate that the controller will use.
                If this value is too large, the aircraft can over-speed on descent.
                This should be set to a value that can be achieved without
                exceeding the lower pitch angle limit and without over-speeding
                the aircraft.</long_desc>
            <default>5.0</default>
        </parameter>
        <parameter name="FW_T_TIME_CONST" type="FLOAT">
            <short_desc>TECS time constant</short_desc>
            <long_desc>This is the time constant of the TECS control algorithm (in seconds).
                Smaller values make it faster to respond, larger values make it slower
                to respond.</long_desc>
            <default>5.0</default>
        </parameter>
        <parameter name="FW_T_THRO_CONST" type="FLOAT">
            <short_desc>TECS Throttle time constant</short_desc>
            <long_desc>This is the time constant of the TECS throttle control algorithm (in seconds).
                Smaller values make it faster to respond, larger values make it slower
                to respond.</long_desc>
            <default>8.0</default>
        </parameter>
        <parameter name="FW_T_THR_DAMP" type="FLOAT">
            <short_desc>Throttle damping factor</short_desc>
            <long_desc>This is the damping gain for the throttle demand loop.
                Increase to add damping to correct for oscillations in speed and height.</long_desc>
            <default>0.5</default>
        </parameter>
        <parameter name="FW_T_INTEG_GAIN" type="FLOAT">
            <short_desc>Integrator gain</short_desc>
            <long_desc>This is the integrator gain on the control loop.
                Increasing this gain increases the speed at which speed
                and height offsets are trimmed out, but reduces damping and
                increases overshoot.</long_desc>
            <default>0.1</default>
        </parameter>
        <parameter name="FW_T_VERT_ACC" type="FLOAT">
            <short_desc>Maximum vertical acceleration</short_desc>
            <long_desc>This is the maximum vertical acceleration (in metres/second square)
                either up or down that the controller will use to correct speed
                or height errors. The default value of 7 m/s/s (equivalent to +- 0.7 g)
                allows for reasonably aggressive pitch changes if required to recover
                from under-speed conditions.</long_desc>
            <default>7.0</default>
        </parameter>
        <parameter name="FW_T_HGT_OMEGA" type="FLOAT">
            <short_desc>Complementary filter &quot;omega&quot; parameter for height</short_desc>
            <long_desc>This is the cross-over frequency (in radians/second) of the complementary
                filter used to fuse vertical acceleration and barometric height to obtain
                an estimate of height rate and height. Increasing this frequency weights
                the solution more towards use of the barometer, whilst reducing it weights
                the solution more towards use of the accelerometer data.</long_desc>
            <default>3.0</default>
        </parameter>
        <parameter name="FW_T_SPD_OMEGA" type="FLOAT">
            <short_desc>Complementary filter &quot;omega&quot; parameter for speed</short_desc>
            <long_desc>This is the cross-over frequency (in radians/second) of the complementary
                filter used to fuse longitudinal acceleration and airspeed to obtain an
                improved airspeed estimate. Increasing this frequency weights the solution
                more towards use of the arispeed sensor, whilst reducing it weights the
                solution more towards use of the accelerometer data.</long_desc>
            <default>2.0</default>
        </parameter>
        <parameter name="FW_T_RLL2THR" type="FLOAT">
            <short_desc>Roll -&gt; Throttle feedforward</short_desc>
            <long_desc>Increasing this gain turn increases the amount of throttle that will
                be used to compensate for the additional drag created by turning.
                Ideally this should be set to  approximately 10 x the extra sink rate
                in m/s created by a 45 degree bank turn. Increase this gain if
                the aircraft initially loses energy in turns and reduce if the
                aircraft initially gains energy in turns. Efficient high aspect-ratio
                aircraft (eg powered sailplanes) can use a lower value, whereas
                inefficient low aspect-ratio models (eg delta wings) can use a higher value.</long_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="FW_T_SPDWEIGHT" type="FLOAT">
            <short_desc>Speed &lt;--&gt; Altitude priority</short_desc>
            <long_desc>This parameter adjusts the amount of weighting that the pitch control
                applies to speed vs height errors. Setting it to 0.0 will cause the
                pitch control to control height and ignore speed errors. This will
                normally improve height accuracy but give larger airspeed errors.
                Setting it to 2.0 will cause the pitch control loop to control speed
                and ignore height errors. This will normally reduce airspeed errors,
                but give larger height errors. The default value of 1.0 allows the pitch
                control to simultaneously control height and speed.
                Note to Glider Pilots - set this parameter to 2.0 (The glider will
                adjust its pitch angle to maintain airspeed, ignoring changes in height).</long_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="FW_T_PTCH_DAMP" type="FLOAT">
            <short_desc>Pitch damping factor</short_desc>
            <long_desc>This is the damping gain for the pitch demand loop. Increase to add
                damping to correct for oscillations in height. The default value of 0.0
                will work well provided the pitch to servo controller has been tuned
                properly.</long_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FW_T_HRATE_P" type="FLOAT">
            <short_desc>Height rate P factor</short_desc>
            <default>0.05</default>
        </parameter>
        <parameter name="FW_T_HRATE_FF" type="FLOAT">
            <short_desc>Height rate FF factor</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FW_T_SRATE_P" type="FLOAT">
            <short_desc>Speed rate P factor</short_desc>
            <default>0.05</default>
        </parameter>
    </group>
    <group name="GPSF">
        <parameter name="NAV_GPSF_LT" type="FLOAT">
            <short_desc>Loiter time</short_desc>
            <long_desc>The amount of time in seconds the system should do open loop loiter and wait for gps recovery
                before it goes into flight termination.</long_desc>
            <default>30.0</default>
            <min>0.0</min>
            <unit>seconds</unit>
        </parameter>
        <parameter name="NAV_GPSF_R" type="FLOAT">
            <short_desc>Open loop loiter roll</short_desc>
            <long_desc>Roll in degrees during the open loop loiter</long_desc>
            <default>15.0</default>
            <min>0.0</min>
            <max>30.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="NAV_GPSF_P" type="FLOAT">
            <short_desc>Open loop loiter pitch</short_desc>
            <long_desc>Pitch in degrees during the open loop loiter</long_desc>
            <default>0.0</default>
            <min>-30.0</min>
            <max>30.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="NAV_GPSF_TR" type="FLOAT">
            <short_desc>Open loop loiter thrust</short_desc>
            <long_desc>Thrust value which is set during the open loop loiter</long_desc>
            <default>0.7</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
    </group>
    <group name="Geofence">
        <parameter name="GF_ON" type="INT32">
            <short_desc>Enable geofence</short_desc>
            <long_desc>Set to 1 to enable geofence.
                Defaults to 1 because geofence is only enabled when the geofence.txt file is present.</long_desc>
            <default>1</default>
            <min>0</min>
            <max>1</max>
        </parameter>
        <parameter name="GF_ALTMODE" type="INT32">
            <short_desc>Geofence altitude mode</short_desc>
            <long_desc>Select which altitude reference should be used
                0 = WGS84, 1 = AMSL</long_desc>
            <default>0</default>
            <min>0</min>
            <max>1</max>
        </parameter>
        <parameter name="GF_SOURCE" type="INT32">
            <short_desc>Geofence source</short_desc>
            <long_desc>Select which position source should be used. Selecting GPS instead of global position makes sure that there is
                no dependence on the position estimator
                0 = global position, 1 = GPS</long_desc>
            <default>0</default>
            <min>0</min>
            <max>1</max>
        </parameter>
        <parameter name="GF_COUNT" type="INT32">
            <short_desc>Geofence counter limit</short_desc>
            <long_desc>Set how many subsequent position measurements outside of the fence are needed before geofence violation is triggered</long_desc>
            <default>-1</default>
            <min>-1</min>
            <max>10</max>
        </parameter>
    </group>
    <group name="L1 Control">
        <parameter name="FW_L1_PERIOD" type="FLOAT">
            <short_desc>L1 period</short_desc>
            <long_desc>This is the L1 distance and defines the tracking
                point ahead of the aircraft its following.
                A value of 25 meters works for most aircraft. Shorten
                slowly during tuning until response is sharp without oscillation.</long_desc>
            <default>25.0</default>
            <min>1.0</min>
            <max>100.0</max>
        </parameter>
        <parameter name="FW_L1_DAMPING" type="FLOAT">
            <short_desc>L1 damping</short_desc>
            <long_desc>Damping factor for L1 control.</long_desc>
            <default>0.75</default>
            <min>0.6</min>
            <max>0.9</max>
        </parameter>
        <parameter name="FW_THR_CRUISE" type="FLOAT">
            <short_desc>Cruise throttle</short_desc>
            <long_desc>This is the throttle setting required to achieve the desired cruise speed. Most airframes have a value of 0.5-0.7.</long_desc>
            <default>0.7</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="FW_THR_SLEW_MAX" type="FLOAT">
            <short_desc>Throttle max slew rate</short_desc>
            <long_desc>Maximum slew rate for the commanded throttle</long_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="FW_P_LIM_MIN" type="FLOAT">
            <short_desc>Negative pitch limit</short_desc>
            <long_desc>The minimum negative pitch the controller will output.</long_desc>
            <default>-45.0</default>
            <min>-60.0</min>
            <max>0.0</max>
            <unit>degrees</unit>
        </parameter>
        <parameter name="FW_P_LIM_MAX" type="FLOAT">
            <short_desc>Positive pitch limit</short_desc>
            <long_desc>The maximum positive pitch the controller will output.</long_desc>
            <default>45.0</default>
            <min>0.0</min>
            <max>60.0</max>
            <unit>degrees</unit>
        </parameter>
        <parameter name="FW_R_LIM" type="FLOAT">
            <short_desc>Controller roll limit</short_desc>
            <long_desc>The maximum roll the controller will output.</long_desc>
            <default>45.0</default>
            <min>0.0</min>
            <unit>degrees</unit>
        </parameter>
        <parameter name="FW_THR_MAX" type="FLOAT">
            <short_desc>Throttle limit max</short_desc>
            <long_desc>This is the maximum throttle % that can be used by the controller.
                For overpowered aircraft, this should be reduced to a value that
                provides sufficient thrust to climb at the maximum pitch angle PTCH_MAX.</long_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="FW_THR_MIN" type="FLOAT">
            <short_desc>Throttle limit min</short_desc>
            <long_desc>This is the minimum throttle % that can be used by the controller.
                For electric aircraft this will normally be set to zero, but can be set
                to a small non-zero value if a folding prop is fitted to prevent the
                prop from folding and unfolding repeatedly in-flight or to provide
                some aerodynamic drag from a turning prop to improve the descent rate.
                For aircraft with internal combustion engine this parameter should be set
                for desired idle rpm.</long_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FW_THR_LND_MAX" type="FLOAT">
            <short_desc>Throttle limit value before flare</short_desc>
            <long_desc>This throttle value will be set as throttle limit at FW_LND_TLALT,
                before arcraft will flare.</long_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="FW_CLMBOUT_DIFF" type="FLOAT">
            <short_desc>Climbout Altitude difference</short_desc>
            <long_desc>If the altitude error exceeds this parameter, the system will climb out
                with maximum throttle and minimum airspeed until it is closer than this
                distance to the desired altitude. Mostly used for takeoff waypoints / modes.
                Set to zero to disable climbout mode (not recommended).</long_desc>
            <default>25.0</default>
        </parameter>
        <parameter name="FW_T_CLMB_MAX" type="FLOAT">
            <short_desc>Maximum climb rate</short_desc>
            <long_desc>This is the best climb rate that the aircraft can achieve with
                the throttle set to THR_MAX and the airspeed set to the
                default value. For electric aircraft make sure this number can be
                achieved towards the end of flight when the battery voltage has reduced.
                The setting of this parameter can be checked by commanding a positive
                altitude change of 100m in loiter, RTL or guided mode. If the throttle
                required to climb is close to THR_MAX and the aircraft is maintaining
                airspeed, then this parameter is set correctly. If the airspeed starts
                to reduce, then the parameter is set to high, and if the throttle
                demand required to climb and maintain speed is noticeably less than
                FW_THR_MAX, then either FW_T_CLMB_MAX should be increased or
                FW_THR_MAX reduced.</long_desc>
            <default>5.0</default>
        </parameter>
        <parameter name="FW_LND_ANG" type="FLOAT">
            <short_desc>Landing slope angle</short_desc>
            <default>5.0</default>
        </parameter>
        <parameter name="FW_LND_HVIRT" type="FLOAT">
            <short_desc>FW_LND_HVIRT</short_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="FW_LND_FLALT" type="FLOAT">
            <short_desc>Landing flare altitude (relative to landing altitude)</short_desc>
            <default>8.0</default>
            <unit>meter</unit>
        </parameter>
        <parameter name="FW_LND_TLALT" type="FLOAT">
            <short_desc>Landing throttle limit altitude (relative landing altitude)</short_desc>
            <long_desc>Default of -1.0f lets the system default to applying throttle
                limiting at 2/3 of the flare altitude.</long_desc>
            <default>-1.0</default>
            <unit>meter</unit>
        </parameter>
        <parameter name="FW_LND_HHDIST" type="FLOAT">
            <short_desc>Landing heading hold horizontal distance</short_desc>
            <default>15.0</default>
        </parameter>
        <parameter name="FW_LND_USETER" type="INT32">
            <short_desc>Enable or disable usage of terrain estimate during landing</short_desc>
            <long_desc>0: disabled, 1: enabled</long_desc>
            <default>0</default>
        </parameter>
    </group>
    <group name="Launch detection">
        <parameter name="LAUN_ALL_ON" type="INT32">
            <short_desc>Enable launch detection</short_desc>
            <default>0</default>
            <min>0</min>
            <max>1</max>
        </parameter>
        <parameter name="LAUN_CAT_A" type="FLOAT">
            <short_desc>Catapult accelerometer theshold</short_desc>
            <long_desc>LAUN_CAT_A * LAUN_CAT_T serves as threshold to trigger launch detection.</long_desc>
            <default>30.0</default>
            <min>0</min>
        </parameter>
        <parameter name="LAUN_CAT_T" type="FLOAT">
            <short_desc>Catapult time theshold</short_desc>
            <long_desc>LAUN_CAT_A * LAUN_CAT_T serves as threshold to trigger launch detection.</long_desc>
            <default>0.05</default>
            <min>0</min>
        </parameter>
        <parameter name="LAUN_CAT_MDEL" type="FLOAT">
            <short_desc>Motor delay</short_desc>
            <long_desc>Delay between starting attitude control and powering up the throttle (giving throttle control to the controller)
                Before this timespan is up the throttle will be set to LAUN_THR_PRE, set to 0 to deactivate</long_desc>
            <default>0.0</default>
            <min>0</min>
            <unit>seconds</unit>
        </parameter>
        <parameter name="LAUN_CAT_PMAX" type="FLOAT">
            <short_desc>Maximum pitch before the throttle is powered up (during motor delay phase)</short_desc>
            <long_desc>This is an extra limit for the maximum pitch which is imposed in the phase before the throttle turns on.
                This allows to limit the maximum pitch angle during a bungee launch (make the launch less steep).</long_desc>
            <default>30.0</default>
            <min>0</min>
            <max>45</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="LAUN_THR_PRE" type="FLOAT">
            <short_desc>Throttle setting while detecting launch</short_desc>
            <long_desc>The throttle is set to this value while the system is waiting for the take-off.</long_desc>
            <default>0.0</default>
            <min>0</min>
            <max>1</max>
        </parameter>
    </group>
    <group name="MAVLink">
        <parameter name="MAV_SYS_ID" type="INT32">
            <short_desc>MAVLink system ID</short_desc>
            <default>1</default>
        </parameter>
        <parameter name="MAV_COMP_ID" type="INT32">
            <short_desc>MAVLink component ID</short_desc>
            <default>50</default>
        </parameter>
        <parameter name="MAV_TYPE" type="INT32">
            <short_desc>MAVLink type</short_desc>
            <default>MAV_TYPE_FIXED_WING</default>
        </parameter>
        <parameter name="MAV_USEHILGPS" type="INT32">
            <short_desc>Use/Accept HIL GPS message (even if not in HIL mode)
                If set to 1 incomming HIL GPS messages are parsed</short_desc>
            <default>0</default>
        </parameter>
        <parameter name="MAV_FWDEXTSP" type="INT32">
            <short_desc>Forward external setpoint messages
                If set to 1 incomming external setpoint messages will be directly forwarded to the controllers if in offboard
                control mode</short_desc>
            <default>1</default>
        </parameter>
    </group>
    <group name="Mission">
        <parameter name="MIS_TAKEOFF_ALT" type="FLOAT">
            <short_desc>Take-off altitude</short_desc>
            <long_desc>Even if first waypoint has altitude less then MIS_TAKEOFF_ALT above home position, system will climb to
                MIS_TAKEOFF_ALT on takeoff, then go to waypoint.</long_desc>
            <default>10.0</default>
            <unit>meters</unit>
        </parameter>
        <parameter name="MIS_ONBOARD_EN" type="INT32">
            <short_desc>Enable persistent onboard mission storage</short_desc>
            <long_desc>When enabled, missions that have been uploaded by the GCS are stored
                and reloaded after reboot persistently.</long_desc>
            <default>1</default>
            <min>0</min>
            <max>1</max>
        </parameter>
        <parameter name="MIS_DIST_1WP" type="FLOAT">
            <short_desc>Maximal horizontal distance from home to first waypoint</short_desc>
            <long_desc>Failsafe check to prevent running mission stored from previous flight at a new takeoff location.
                Set a value of zero or less to disable. The mission will not be started if the current
                waypoint is more distant than MIS_DIS_1WP from the current position.</long_desc>
            <default>500</default>
            <min>0</min>
            <max>1000</max>
        </parameter>
        <parameter name="MIS_ALTMODE" type="INT32">
            <short_desc>Altitude setpoint mode</short_desc>
            <long_desc>0: the system will follow a zero order hold altitude setpoint
                1: the system will follow a first order hold altitude setpoint
                values follow the definition in enum mission_altitude_mode</long_desc>
            <default>0</default>
            <min>0</min>
            <max>1</max>
        </parameter>
        <parameter name="NAV_LOITER_RAD" type="FLOAT">
            <short_desc>Loiter radius (FW only)</short_desc>
            <long_desc>Default value of loiter radius for missions, loiter, RTL, etc. (fixedwing only).</long_desc>
            <default>50.0</default>
            <min>0.0</min>
            <unit>meters</unit>
        </parameter>
        <parameter name="NAV_ACC_RAD" type="FLOAT">
            <short_desc>Acceptance Radius</short_desc>
            <long_desc>Default acceptance radius, overridden by acceptance radius of waypoint if set.</long_desc>
            <default>25.0</default>
            <min>1.0</min>
            <unit>meters</unit>
        </parameter>
        <parameter name="NAV_DLL_OBC" type="INT32">
            <short_desc>Set OBC mode for data link loss</short_desc>
            <long_desc>If set to 1 the behaviour on data link loss is set to a mode according to the OBC rules</long_desc>
            <default>0</default>
            <min>0</min>
        </parameter>
        <parameter name="NAV_RCL_OBC" type="INT32">
            <short_desc>Set OBC mode for rc loss</short_desc>
            <long_desc>If set to 1 the behaviour on data link loss is set to a mode according to the OBC rules</long_desc>
            <default>0</default>
            <min>0</min>
        </parameter>
    </group>
    <group name="Multicopter Attitude Control">
        <parameter name="MC_ROLL_P" type="FLOAT">
            <short_desc>Roll P gain</short_desc>
            <long_desc>Roll proportional gain, i.e. desired angular speed in rad/s for error 1 rad.</long_desc>
            <default>6.0</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MC_ROLLRATE_P" type="FLOAT">
            <short_desc>Roll rate P gain</short_desc>
            <long_desc>Roll rate proportional gain, i.e. control output for angular speed error 1 rad/s.</long_desc>
            <default>0.1</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MC_ROLLRATE_I" type="FLOAT">
            <short_desc>Roll rate I gain</short_desc>
            <long_desc>Roll rate integral gain. Can be set to compensate static thrust difference or gravity center offset.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MC_ROLLRATE_D" type="FLOAT">
            <short_desc>Roll rate D gain</short_desc>
            <long_desc>Roll rate differential gain. Small values help reduce fast oscillations. If value is too big oscillations will appear again.</long_desc>
            <default>0.002</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MC_PITCH_P" type="FLOAT">
            <short_desc>Pitch P gain</short_desc>
            <long_desc>Pitch proportional gain, i.e. desired angular speed in rad/s for error 1 rad.</long_desc>
            <default>6.0</default>
            <min>0.0</min>
            <unit>1/s</unit>
        </parameter>
        <parameter name="MC_PITCHRATE_P" type="FLOAT">
            <short_desc>Pitch rate P gain</short_desc>
            <long_desc>Pitch rate proportional gain, i.e. control output for angular speed error 1 rad/s.</long_desc>
            <default>0.1</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MC_PITCHRATE_I" type="FLOAT">
            <short_desc>Pitch rate I gain</short_desc>
            <long_desc>Pitch rate integral gain. Can be set to compensate static thrust difference or gravity center offset.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MC_PITCHRATE_D" type="FLOAT">
            <short_desc>Pitch rate D gain</short_desc>
            <long_desc>Pitch rate differential gain. Small values help reduce fast oscillations. If value is too big oscillations will appear again.</long_desc>
            <default>0.002</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MC_YAW_P" type="FLOAT">
            <short_desc>Yaw P gain</short_desc>
            <long_desc>Yaw proportional gain, i.e. desired angular speed in rad/s for error 1 rad.</long_desc>
            <default>2.0</default>
            <min>0.0</min>
            <unit>1/s</unit>
        </parameter>
        <parameter name="MC_YAWRATE_P" type="FLOAT">
            <short_desc>Yaw rate P gain</short_desc>
            <long_desc>Yaw rate proportional gain, i.e. control output for angular speed error 1 rad/s.</long_desc>
            <default>0.3</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MC_YAWRATE_I" type="FLOAT">
            <short_desc>Yaw rate I gain</short_desc>
            <long_desc>Yaw rate integral gain. Can be set to compensate static thrust difference or gravity center offset.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MC_YAWRATE_D" type="FLOAT">
            <short_desc>Yaw rate D gain</short_desc>
            <long_desc>Yaw rate differential gain. Small values help reduce fast oscillations. If value is too big oscillations will appear again.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MC_YAW_FF" type="FLOAT">
            <short_desc>Yaw feed forward</short_desc>
            <long_desc>Feed forward weight for manual yaw control. 0 will give slow responce and no overshot, 1 - fast responce and big overshot.</long_desc>
            <default>0.5</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MC_YAWRATE_MAX" type="FLOAT">
            <short_desc>Max yaw rate</short_desc>
            <long_desc>Limit for yaw rate, has effect for large rotations in autonomous mode, to avoid large control output and mixer saturation.</long_desc>
            <default>120.0</default>
            <min>0.0</min>
            <max>360.0</max>
            <unit>deg/s</unit>
        </parameter>
        <parameter name="MC_MAN_R_MAX" type="FLOAT">
            <short_desc>Max manual roll</short_desc>
            <default>35.0</default>
            <min>0.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MC_MAN_P_MAX" type="FLOAT">
            <short_desc>Max manual pitch</short_desc>
            <default>35.0</default>
            <min>0.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MC_MAN_Y_MAX" type="FLOAT">
            <short_desc>Max manual yaw rate</short_desc>
            <default>120.0</default>
            <min>0.0</min>
            <unit>deg/s</unit>
        </parameter>
        <parameter name="MC_ACRO_R_MAX" type="FLOAT">
            <short_desc>Max acro roll rate</short_desc>
            <default>90.0</default>
            <min>0.0</min>
            <max>360.0</max>
            <unit>deg/s</unit>
        </parameter>
        <parameter name="MC_ACRO_P_MAX" type="FLOAT">
            <short_desc>Max acro pitch rate</short_desc>
            <default>90.0</default>
            <min>0.0</min>
            <max>360.0</max>
            <unit>deg/s</unit>
        </parameter>
        <parameter name="MC_ACRO_Y_MAX" type="FLOAT">
            <short_desc>Max acro yaw rate</short_desc>
            <default>120.0</default>
            <min>0.0</min>
            <unit>deg/s</unit>
        </parameter>
    </group>
    <group name="Multicopter Position Control">
        <parameter name="MPC_THR_MIN" type="FLOAT">
            <short_desc>Minimum thrust</short_desc>
            <long_desc>Minimum vertical thrust. It's recommended to set it &gt; 0 to avoid free fall with zero thrust.</long_desc>
            <default>0.1</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MPC_THR_MAX" type="FLOAT">
            <short_desc>Maximum thrust</short_desc>
            <long_desc>Limit max allowed thrust.</long_desc>
            <default>1.0</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MPC_Z_P" type="FLOAT">
            <short_desc>Proportional gain for vertical position error</short_desc>
            <default>1.0</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MPC_Z_VEL_P" type="FLOAT">
            <short_desc>Proportional gain for vertical velocity error</short_desc>
            <default>0.1</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MPC_Z_VEL_I" type="FLOAT">
            <short_desc>Integral gain for vertical velocity error</short_desc>
            <long_desc>Non zero value allows hovering thrust estimation on stabilized or autonomous takeoff.</long_desc>
            <default>0.02</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MPC_Z_VEL_D" type="FLOAT">
            <short_desc>Differential gain for vertical velocity error</short_desc>
            <default>0.0</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MPC_Z_VEL_MAX" type="FLOAT">
            <short_desc>Maximum vertical velocity</short_desc>
            <long_desc>Maximum vertical velocity in AUTO mode and endpoint for stabilized modes (ALTCTRL, POSCTRL).</long_desc>
            <default>5.0</default>
            <min>0.0</min>
            <unit>m/s</unit>
        </parameter>
        <parameter name="MPC_Z_FF" type="FLOAT">
            <short_desc>Vertical velocity feed forward</short_desc>
            <long_desc>Feed forward weight for altitude control in stabilized modes (ALTCTRL, POSCTRL). 0 will give slow responce and no overshot, 1 - fast responce and big overshot.</long_desc>
            <default>0.5</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MPC_XY_P" type="FLOAT">
            <short_desc>Proportional gain for horizontal position error</short_desc>
            <default>1.0</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MPC_XY_VEL_P" type="FLOAT">
            <short_desc>Proportional gain for horizontal velocity error</short_desc>
            <default>0.1</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MPC_XY_VEL_I" type="FLOAT">
            <short_desc>Integral gain for horizontal velocity error</short_desc>
            <long_desc>Non-zero value allows to resist wind.</long_desc>
            <default>0.02</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MPC_XY_VEL_D" type="FLOAT">
            <short_desc>Differential gain for horizontal velocity error. Small values help reduce fast oscillations. If value is too big oscillations will appear again</short_desc>
            <default>0.01</default>
            <min>0.0</min>
        </parameter>
        <parameter name="MPC_XY_VEL_MAX" type="FLOAT">
            <short_desc>Maximum horizontal velocity</short_desc>
            <long_desc>Maximum horizontal velocity in AUTO mode and endpoint for position stabilized mode (POSCTRL).</long_desc>
            <default>5.0</default>
            <min>0.0</min>
            <unit>m/s</unit>
        </parameter>
        <parameter name="MPC_XY_FF" type="FLOAT">
            <short_desc>Horizontal velocity feed forward</short_desc>
            <long_desc>Feed forward weight for position control in position control mode (POSCTRL). 0 will give slow responce and no overshot, 1 - fast responce and big overshot.</long_desc>
            <default>0.5</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MPC_TILTMAX_AIR" type="FLOAT">
            <short_desc>Maximum tilt angle in air</short_desc>
            <long_desc>Limits maximum tilt in AUTO and POSCTRL modes during flight.</long_desc>
            <default>45.0</default>
            <min>0.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MPC_TILTMAX_LND" type="FLOAT">
            <short_desc>Maximum tilt during landing</short_desc>
            <long_desc>Limits maximum tilt angle on landing.</long_desc>
            <default>15.0</default>
            <min>0.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MPC_LAND_SPEED" type="FLOAT">
            <short_desc>Landing descend rate</short_desc>
            <default>1.0</default>
            <min>0.0</min>
            <unit>m/s</unit>
        </parameter>
    </group>
    <group name="Payload drop">
        <parameter name="BD_GPROPERTIES" type="FLOAT">
            <short_desc>Ground drag property</short_desc>
            <long_desc>This parameter encodes the ground drag coefficient and the corresponding
                decrease in wind speed from the plane altitude to ground altitude.</long_desc>
            <default>0.03</default>
            <min>0.001</min>
            <max>0.1</max>
            <unit>unknown</unit>
        </parameter>
        <parameter name="BD_TURNRADIUS" type="FLOAT">
            <short_desc>Plane turn radius</short_desc>
            <long_desc>The planes known minimal turn radius - use a higher value
                to make the plane maneuver more distant from the actual drop
                position. This is to ensure the wings are level during the drop.</long_desc>
            <default>120.0</default>
            <min>30.0</min>
            <max>500.0</max>
            <unit>meter</unit>
        </parameter>
        <parameter name="BD_PRECISION" type="FLOAT">
            <short_desc>Drop precision</short_desc>
            <long_desc>If the system is closer than this distance on passing over the
                drop position, it will release the payload. This is a safeguard
                to prevent a drop out of the required accuracy.</long_desc>
            <default>30.0</default>
            <min>1.0</min>
            <max>80.0</max>
            <unit>meter</unit>
        </parameter>
        <parameter name="BD_OBJ_CD" type="FLOAT">
            <short_desc>Payload drag coefficient of the dropped object</short_desc>
            <long_desc>The drag coefficient (cd) is the typical drag
                constant for air. It is in general object specific,
                but the closest primitive shape to the actual object
                should give good results:
                http://en.wikipedia.org/wiki/Drag_coefficient</long_desc>
            <default>0.1</default>
            <min>0.08</min>
            <max>1.5</max>
            <unit>meter</unit>
        </parameter>
        <parameter name="BD_OBJ_MASS" type="FLOAT">
            <short_desc>Payload mass</short_desc>
            <long_desc>A typical small toy ball:
                0.025 kg
                OBC water bottle:
                0.6 kg</long_desc>
            <default>0.6</default>
            <min>0.001</min>
            <max>5.0</max>
            <unit>kilogram</unit>
        </parameter>
        <parameter name="BD_OBJ_SURFACE" type="FLOAT">
            <short_desc>Payload front surface area</short_desc>
            <long_desc>A typical small toy ball:
                (0.045 * 0.045) / 4.0 * pi = 0.001590 m^2
                OBC water bottle:
                (0.063 * 0.063) / 4.0 * pi = 0.003117 m^2</long_desc>
            <default>0.00311724531</default>
            <min>0.001</min>
            <max>0.5</max>
            <unit>m^2</unit>
        </parameter>
    </group>
    <group name="Position Estimator">
        <parameter name="PE_VEL_DELAY_MS" type="INT32">
            <short_desc>Velocity estimate delay</short_desc>
            <long_desc>The delay in milliseconds of the velocity estimate from GPS.</long_desc>
            <default>230</default>
            <min>0</min>
            <max>1000</max>
        </parameter>
        <parameter name="PE_POS_DELAY_MS" type="INT32">
            <short_desc>Position estimate delay</short_desc>
            <long_desc>The delay in milliseconds of the position estimate from GPS.</long_desc>
            <default>210</default>
            <min>0</min>
            <max>1000</max>
        </parameter>
        <parameter name="PE_HGT_DELAY_MS" type="INT32">
            <short_desc>Height estimate delay</short_desc>
            <long_desc>The delay in milliseconds of the height estimate from the barometer.</long_desc>
            <default>350</default>
            <min>0</min>
            <max>1000</max>
        </parameter>
        <parameter name="PE_MAG_DELAY_MS" type="INT32">
            <short_desc>Mag estimate delay</short_desc>
            <long_desc>The delay in milliseconds of the magnetic field estimate from
                the magnetometer.</long_desc>
            <default>30</default>
            <min>0</min>
            <max>1000</max>
        </parameter>
        <parameter name="PE_TAS_DELAY_MS" type="INT32">
            <short_desc>True airspeeed estimate delay</short_desc>
            <long_desc>The delay in milliseconds of the airspeed estimate.</long_desc>
            <default>210</default>
            <min>0</min>
            <max>1000</max>
        </parameter>
        <parameter name="PE_GPS_ALT_WGT" type="FLOAT">
            <short_desc>GPS vs. barometric altitude update weight</short_desc>
            <long_desc>RE-CHECK this.</long_desc>
            <default>0.9</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="PE_EAS_NOISE" type="FLOAT">
            <short_desc>Airspeed measurement noise</short_desc>
            <long_desc>Increasing this value will make the filter trust this sensor
                less and trust other sensors more.</long_desc>
            <default>1.4</default>
            <min>0.5</min>
            <max>5.0</max>
        </parameter>
        <parameter name="PE_VELNE_NOISE" type="FLOAT">
            <short_desc>Velocity measurement noise in north-east (horizontal) direction</short_desc>
            <long_desc>Generic default: 0.3, multicopters: 0.5, ground vehicles: 0.5</long_desc>
            <default>0.3</default>
            <min>0.05</min>
            <max>5.0</max>
        </parameter>
        <parameter name="PE_VELD_NOISE" type="FLOAT">
            <short_desc>Velocity noise in down (vertical) direction</short_desc>
            <long_desc>Generic default: 0.5, multicopters: 0.7, ground vehicles: 0.7</long_desc>
            <default>0.5</default>
            <min>0.05</min>
            <max>5.0</max>
        </parameter>
        <parameter name="PE_POSNE_NOISE" type="FLOAT">
            <short_desc>Position noise in north-east (horizontal) direction</short_desc>
            <long_desc>Generic defaults: 0.5, multicopters: 0.5, ground vehicles: 0.5</long_desc>
            <default>0.5</default>
            <min>0.1</min>
            <max>10.0</max>
        </parameter>
        <parameter name="PE_POSD_NOISE" type="FLOAT">
            <short_desc>Position noise in down (vertical) direction</short_desc>
            <long_desc>Generic defaults: 0.5, multicopters: 1.0, ground vehicles: 1.0</long_desc>
            <default>0.5</default>
            <min>0.1</min>
            <max>10.0</max>
        </parameter>
        <parameter name="PE_MAG_NOISE" type="FLOAT">
            <short_desc>Magnetometer measurement noise</short_desc>
            <long_desc>Generic defaults: 0.05, multicopters: 0.05, ground vehicles: 0.05</long_desc>
            <default>0.05</default>
            <min>0.1</min>
            <max>10.0</max>
        </parameter>
        <parameter name="PE_GYRO_PNOISE" type="FLOAT">
            <short_desc>Gyro process noise</short_desc>
            <long_desc>Generic defaults: 0.015, multicopters: 0.015, ground vehicles: 0.015.
                This noise controls how much the filter trusts the gyro measurements.
                Increasing it makes the filter trust the gyro less and other sensors more.</long_desc>
            <default>0.015</default>
            <min>0.001</min>
            <max>0.05</max>
        </parameter>
        <parameter name="PE_ACC_PNOISE" type="FLOAT">
            <short_desc>Accelerometer process noise</short_desc>
            <long_desc>Generic defaults: 0.25, multicopters: 0.25, ground vehicles: 0.25.
                Increasing this value makes the filter trust the accelerometer less
                and other sensors more.</long_desc>
            <default>0.25</default>
            <min>0.05</min>
            <max>1.0</max>
        </parameter>
        <parameter name="PE_GBIAS_PNOISE" type="FLOAT">
            <short_desc>Gyro bias estimate process noise</short_desc>
            <long_desc>Generic defaults: 1e-07f, multicopters: 1e-07f, ground vehicles: 1e-07f.
                Increasing this value will make the gyro bias converge faster but noisier.</long_desc>
            <default>1e-07</default>
            <min>0.0000001</min>
            <max>0.00001</max>
        </parameter>
        <parameter name="PE_ABIAS_PNOISE" type="FLOAT">
            <short_desc>Accelerometer bias estimate process noise</short_desc>
            <long_desc>Generic defaults: 0.0001f, multicopters: 0.0001f, ground vehicles: 0.0001f.
                Increasing this value makes the bias estimation faster and noisier.</long_desc>
            <default>0.00005</default>
            <min>0.00001</min>
            <max>0.001</max>
        </parameter>
        <parameter name="PE_MAGE_PNOISE" type="FLOAT">
            <short_desc>Magnetometer earth frame offsets process noise</short_desc>
            <long_desc>Generic defaults: 0.0001, multicopters: 0.0001, ground vehicles: 0.0001.
                Increasing this value makes the magnetometer earth bias estimate converge
                faster but also noisier.</long_desc>
            <default>0.0003</default>
            <min>0.0001</min>
            <max>0.01</max>
        </parameter>
        <parameter name="PE_MAGB_PNOISE" type="FLOAT">
            <short_desc>Magnetometer body frame offsets process noise</short_desc>
            <long_desc>Generic defaults: 0.0003, multicopters: 0.0003, ground vehicles: 0.0003.
                Increasing this value makes the magnetometer body bias estimate converge faster
                but also noisier.</long_desc>
            <default>0.0003</default>
            <min>0.0001</min>
            <max>0.01</max>
        </parameter>
        <parameter name="PE_POSDEV_INIT" type="FLOAT">
            <short_desc>Threshold for filter initialization</short_desc>
            <long_desc>If the standard deviation of the GPS position estimate is below this threshold
                in meters, the filter will initialize.</long_desc>
            <default>5.0</default>
            <min>0.3</min>
            <max>10.0</max>
        </parameter>
    </group>
    <group name="Position Estimator INAV">
        <parameter name="INAV_W_Z_BARO" type="FLOAT">
            <short_desc>Z axis weight for barometer</short_desc>
            <long_desc>Weight (cutoff frequency) for barometer altitude measurements.</long_desc>
            <default>0.5</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="INAV_W_Z_GPS_P" type="FLOAT">
            <short_desc>Z axis weight for GPS</short_desc>
            <long_desc>Weight (cutoff frequency) for GPS altitude measurements. GPS altitude data is very noisy and should be used only as slow correction for baro offset.</long_desc>
            <default>0.005</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="INAV_W_Z_VIS_P" type="FLOAT">
            <short_desc>Z axis weight for vision</short_desc>
            <long_desc>Weight (cutoff frequency) for vision altitude measurements. vision altitude data is very noisy and should be used only as slow correction for baro offset.</long_desc>
            <default>0.5</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="INAV_W_Z_SONAR" type="FLOAT">
            <short_desc>Z axis weight for sonar</short_desc>
            <long_desc>Weight (cutoff frequency) for sonar measurements.</long_desc>
            <default>3.0</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="INAV_W_XY_GPS_P" type="FLOAT">
            <short_desc>XY axis weight for GPS position</short_desc>
            <long_desc>Weight (cutoff frequency) for GPS position measurements.</long_desc>
            <default>1.0</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="INAV_W_XY_GPS_V" type="FLOAT">
            <short_desc>XY axis weight for GPS velocity</short_desc>
            <long_desc>Weight (cutoff frequency) for GPS velocity measurements.</long_desc>
            <default>2.0</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="INAV_W_XY_VIS_P" type="FLOAT">
            <short_desc>XY axis weight for vision position</short_desc>
            <long_desc>Weight (cutoff frequency) for vision position measurements.</long_desc>
            <default>5.0</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="INAV_W_XY_VIS_V" type="FLOAT">
            <short_desc>XY axis weight for vision velocity</short_desc>
            <long_desc>Weight (cutoff frequency) for vision velocity measurements.</long_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="INAV_W_XY_FLOW" type="FLOAT">
            <short_desc>XY axis weight for optical flow</short_desc>
            <long_desc>Weight (cutoff frequency) for optical flow (velocity) measurements.</long_desc>
            <default>5.0</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="INAV_W_XY_RES_V" type="FLOAT">
            <short_desc>XY axis weight for resetting velocity</short_desc>
            <long_desc>When velocity sources lost slowly decrease estimated horizontal velocity with this weight.</long_desc>
            <default>0.5</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="INAV_W_GPS_FLOW" type="FLOAT">
            <short_desc>XY axis weight factor for GPS when optical flow available</short_desc>
            <long_desc>When optical flow data available, multiply GPS weights (for position and velocity) by this factor.</long_desc>
            <default>0.1</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="INAV_W_ACC_BIAS" type="FLOAT">
            <short_desc>Accelerometer bias estimation weight</short_desc>
            <long_desc>Weight (cutoff frequency) for accelerometer bias estimation. 0 to disable.</long_desc>
            <default>0.05</default>
            <min>0.0</min>
            <max>0.1</max>
        </parameter>
        <parameter name="INAV_FLOW_K" type="FLOAT">
            <short_desc>Optical flow scale factor</short_desc>
            <long_desc>Factor to convert raw optical flow (in pixels) to radians [rad/px].</long_desc>
            <default>0.15</default>
            <min>0.0</min>
            <max>1.0</max>
            <unit>rad/px</unit>
        </parameter>
        <parameter name="INAV_FLOW_Q_MIN" type="FLOAT">
            <short_desc>Minimal acceptable optical flow quality</short_desc>
            <long_desc>0 - lowest quality, 1 - best quality.</long_desc>
            <default>0.5</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="INAV_SONAR_FILT" type="FLOAT">
            <short_desc>Weight for sonar filter</short_desc>
            <long_desc>Sonar filter detects spikes on sonar measurements and used to detect new surface level.</long_desc>
            <default>0.05</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="INAV_SONAR_ERR" type="FLOAT">
            <short_desc>Sonar maximal error for new surface</short_desc>
            <long_desc>If sonar measurement error is larger than this value it skiped (spike) or accepted as new surface level (if offset is stable).</long_desc>
            <default>0.5</default>
            <min>0.0</min>
            <max>1.0</max>
            <unit>m</unit>
        </parameter>
        <parameter name="INAV_LAND_T" type="FLOAT">
            <short_desc>Land detector time</short_desc>
            <long_desc>Vehicle assumed landed if no altitude changes happened during this time on low throttle.</long_desc>
            <default>3.0</default>
            <min>0.0</min>
            <max>10.0</max>
            <unit>s</unit>
        </parameter>
        <parameter name="INAV_LAND_DISP" type="FLOAT">
            <short_desc>Land detector altitude dispersion threshold</short_desc>
            <long_desc>Dispersion threshold for triggering land detector.</long_desc>
            <default>0.7</default>
            <min>0.0</min>
            <max>10.0</max>
            <unit>m</unit>
        </parameter>
        <parameter name="INAV_LAND_THR" type="FLOAT">
            <short_desc>Land detector throttle threshold</short_desc>
            <long_desc>Value should be lower than minimal hovering thrust. Half of it is good choice.</long_desc>
            <default>0.2</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="INAV_DELAY_GPS" type="FLOAT">
            <short_desc>GPS delay</short_desc>
            <long_desc>GPS delay compensation</long_desc>
            <default>0.2</default>
            <min>0.0</min>
            <max>1.0</max>
            <unit>s</unit>
        </parameter>
        <parameter name="CBRK_NO_VISION" type="INT32">
            <short_desc>Disable vision input</short_desc>
            <long_desc>Set to the appropriate key (328754) to disable vision input.</long_desc>
            <default>0</default>
            <min>0</min>
            <max>1</max>
        </parameter>
    </group>
    <group name="RCL">
        <parameter name="NAV_RCL_LT" type="FLOAT">
            <short_desc>Loiter Time</short_desc>
            <long_desc>The amount of time in seconds the system should loiter at current position before termination
                Set to -1 to make the system skip loitering</long_desc>
            <default>120.0</default>
            <min>-1.0</min>
            <unit>seconds</unit>
        </parameter>
    </group>
    <group name="RTL">
        <parameter name="RTL_LOITER_RAD" type="FLOAT">
            <short_desc>Loiter radius after RTL (FW only)</short_desc>
            <long_desc>Default value of loiter radius after RTL (fixedwing only).</long_desc>
            <default>50.0</default>
            <min>0.0</min>
            <unit>meters</unit>
        </parameter>
        <parameter name="RTL_RETURN_ALT" type="FLOAT">
            <short_desc>RTL altitude</short_desc>
            <long_desc>Altitude to fly back in RTL in meters</long_desc>
            <default>100</default>
            <min>0</min>
            <max>1</max>
            <unit>meters</unit>
        </parameter>
        <parameter name="RTL_DESCEND_ALT" type="FLOAT">
            <short_desc>RTL loiter altitude</short_desc>
            <long_desc>Stay at this altitude above home position after RTL descending.
                Land (i.e. slowly descend) from this altitude if autolanding allowed.</long_desc>
            <default>20</default>
            <min>0</min>
            <max>100</max>
            <unit>meters</unit>
        </parameter>
        <parameter name="RTL_LAND_DELAY" type="FLOAT">
            <short_desc>RTL delay</short_desc>
            <long_desc>Delay after descend before landing in RTL mode.
                If set to -1 the system will not land but loiter at NAV_LAND_ALT.</long_desc>
            <default>-1.0</default>
            <min>-1.0</min>
            <unit>seconds</unit>
        </parameter>
    </group>
    <group name="Radio Calibration">
        <parameter name="RC1_MIN" type="FLOAT">
            <short_desc>RC Channel 1 Minimum</short_desc>
            <long_desc>Minimum value for RC channel 1</long_desc>
            <default>1000.0</default>
            <min>800.0</min>
            <max>1500.0</max>
        </parameter>
        <parameter name="RC1_TRIM" type="FLOAT">
            <short_desc>RC Channel 1 Trim</short_desc>
            <long_desc>Mid point value (same as min for throttle)</long_desc>
            <default>1500.0</default>
            <min>800.0</min>
            <max>2200.0</max>
        </parameter>
        <parameter name="RC1_MAX" type="FLOAT">
            <short_desc>RC Channel 1 Maximum</short_desc>
            <long_desc>Maximum value for RC channel 1</long_desc>
            <default>2000.0</default>
            <min>1500.0</min>
            <max>2200.0</max>
        </parameter>
        <parameter name="RC1_REV" type="FLOAT">
            <short_desc>RC Channel 1 Reverse</short_desc>
            <long_desc>Set to -1 to reverse channel.</long_desc>
            <default>1.0</default>
            <min>-1.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="RC1_DZ" type="FLOAT">
            <short_desc>RC Channel 1 dead zone</short_desc>
            <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
            <default>10.0</default>
            <min>0.0</min>
            <max>100.0</max>
        </parameter>
        <parameter name="RC2_MIN" type="FLOAT">
            <short_desc>RC Channel 2 Minimum</short_desc>
            <long_desc>Minimum value for RC channel 2</long_desc>
            <default>1000.0</default>
            <min>800.0</min>
            <max>1500.0</max>
        </parameter>
        <parameter name="RC2_TRIM" type="FLOAT">
            <short_desc>RC Channel 2 Trim</short_desc>
            <long_desc>Mid point value (same as min for throttle)</long_desc>
            <default>1500.0</default>
            <min>800.0</min>
            <max>2200.0</max>
        </parameter>
        <parameter name="RC2_MAX" type="FLOAT">
            <short_desc>RC Channel 2 Maximum</short_desc>
            <long_desc>Maximum value for RC channel 2</long_desc>
            <default>2000.0</default>
            <min>1500.0</min>
            <max>2200.0</max>
        </parameter>
        <parameter name="RC2_REV" type="FLOAT">
            <short_desc>RC Channel 2 Reverse</short_desc>
            <long_desc>Set to -1 to reverse channel.</long_desc>
            <default>1.0</default>
            <min>-1.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="RC2_DZ" type="FLOAT">
            <short_desc>RC Channel 2 dead zone</short_desc>
            <long_desc>The +- range of this value around the trim value will be considered as zero.</long_desc>
            <default>10.0</default>
            <min>0.0</min>
            <max>100.0</max>
        </parameter>
        <parameter name="RC_DSM_BIND" type="INT32">
            <short_desc>DSM binding trigger</short_desc>
            <long_desc>-1 = Idle, 0 = Start DSM2 bind, 1 = Start DSMX bind</long_desc>
            <default>-1</default>
        </parameter>
        <parameter name="RC_MAP_ROLL" type="INT32">
            <short_desc>Roll control channel mapping</short_desc>
            <long_desc>The channel index (starting from 1 for channel 1) indicates
                which channel should be used for reading roll inputs from.
                A value of zero indicates the switch is not assigned.</long_desc>
            <default>1</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_PITCH" type="INT32">
            <short_desc>Pitch control channel mapping</short_desc>
            <long_desc>The channel index (starting from 1 for channel 1) indicates
                which channel should be used for reading pitch inputs from.
                A value of zero indicates the switch is not assigned.</long_desc>
            <default>2</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_THROTTLE" type="INT32">
            <short_desc>Throttle control channel mapping</short_desc>
            <long_desc>The channel index (starting from 1 for channel 1) indicates
                which channel should be used for reading throttle inputs from.
                A value of zero indicates the switch is not assigned.</long_desc>
            <default>3</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_YAW" type="INT32">
            <short_desc>Yaw control channel mapping</short_desc>
            <long_desc>The channel index (starting from 1 for channel 1) indicates
                which channel should be used for reading yaw inputs from.
                A value of zero indicates the switch is not assigned.</long_desc>
            <default>4</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_MODE_SW" type="INT32">
            <short_desc>Mode switch channel mapping</short_desc>
            <long_desc>This is the main flight mode selector.
                The channel index (starting from 1 for channel 1) indicates
                which channel should be used for deciding about the main mode.
                A value of zero indicates the switch is not assigned.</long_desc>
            <default>0</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_RETURN_SW" type="INT32">
            <short_desc>Return switch channel mapping</short_desc>
            <default>0</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_POSCTL_SW" type="INT32">
            <short_desc>Posctl switch channel mapping</short_desc>
            <default>0</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_LOITER_SW" type="INT32">
            <short_desc>Loiter switch channel mapping</short_desc>
            <default>0</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_ACRO_SW" type="INT32">
            <short_desc>Acro switch channel mapping</short_desc>
            <default>0</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_OFFB_SW" type="INT32">
            <short_desc>Offboard switch channel mapping</short_desc>
            <default>0</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_FLAPS" type="INT32">
            <short_desc>Flaps channel mapping</short_desc>
            <default>0</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_AUX1" type="INT32">
            <short_desc>Auxiliary switch 1 channel mapping</short_desc>
            <long_desc>Default function: Camera pitch</long_desc>
            <default>0</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_AUX2" type="INT32">
            <short_desc>Auxiliary switch 2 channel mapping</short_desc>
            <long_desc>Default function: Camera roll</long_desc>
            <default>0</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_MAP_AUX3" type="INT32">
            <short_desc>Auxiliary switch 3 channel mapping</short_desc>
            <long_desc>Default function: Camera azimuth / yaw</long_desc>
            <default>0</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_FAILS_THR" type="INT32">
            <short_desc>Failsafe channel PWM threshold</short_desc>
            <default>0</default>
            <min>800</min>
            <max>2200</max>
        </parameter>
    </group>
    <group name="SD Logging">
        <parameter name="SDLOG_RATE" type="INT32">
            <short_desc>Logging rate</short_desc>
            <long_desc>A value of -1 indicates the commandline argument
                should be obeyed. A value of 0 sets the minimum rate,
                any other value is interpreted as rate in Hertz. This
                parameter is only read out before logging starts (which
                commonly is before arming).</long_desc>
            <default>-1</default>
            <min>-1</min>
            <max>1</max>
        </parameter>
        <parameter name="SDLOG_EXT" type="INT32">
            <short_desc>Enable extended logging mode</short_desc>
            <long_desc>A value of -1 indicates the commandline argument
                should be obeyed. A value of 0 disables extended
                logging mode, a value of 1 enables it. This
                parameter is only read out before logging starts
                (which commonly is before arming).</long_desc>
            <default>-1</default>
            <min>-1</min>
            <max>1</max>
        </parameter>
    </group>
    <group name="Sensor Calibration">
        <parameter name="SENS_GYRO_XOFF" type="FLOAT">
            <short_desc>Gyro X-axis offset</short_desc>
            <default>0.0</default>
            <min>-10.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="SENS_GYRO_YOFF" type="FLOAT">
            <short_desc>Gyro Y-axis offset</short_desc>
            <default>0.0</default>
            <min>-10.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="SENS_GYRO_ZOFF" type="FLOAT">
            <short_desc>Gyro Z-axis offset</short_desc>
            <default>0.0</default>
            <min>-5.0</min>
            <max>5.0</max>
        </parameter>
        <parameter name="SENS_GYRO_XSCALE" type="FLOAT">
            <short_desc>Gyro X-axis scaling factor</short_desc>
            <default>1.0</default>
            <min>-1.5</min>
            <max>1.5</max>
        </parameter>
        <parameter name="SENS_GYRO_YSCALE" type="FLOAT">
            <short_desc>Gyro Y-axis scaling factor</short_desc>
            <default>1.0</default>
            <min>-1.5</min>
            <max>1.5</max>
        </parameter>
        <parameter name="SENS_GYRO_ZSCALE" type="FLOAT">
            <short_desc>Gyro Z-axis scaling factor</short_desc>
            <default>1.0</default>
            <min>-1.5</min>
            <max>1.5</max>
        </parameter>
        <parameter name="SENS_MAG_XOFF" type="FLOAT">
            <short_desc>Magnetometer X-axis offset</short_desc>
            <default>0.0</default>
            <min>-500.0</min>
            <max>500.0</max>
        </parameter>
        <parameter name="SENS_MAG_YOFF" type="FLOAT">
            <short_desc>Magnetometer Y-axis offset</short_desc>
            <default>0.0</default>
            <min>-500.0</min>
            <max>500.0</max>
        </parameter>
        <parameter name="SENS_MAG_ZOFF" type="FLOAT">
            <short_desc>Magnetometer Z-axis offset</short_desc>
            <default>0.0</default>
            <min>-500.0</min>
            <max>500.0</max>
        </parameter>
        <parameter name="SENS_MAG_XSCALE" type="FLOAT">
            <short_desc>Magnetometer X-axis scaling factor</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="SENS_MAG_YSCALE" type="FLOAT">
            <short_desc>Magnetometer Y-axis scaling factor</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="SENS_MAG_ZSCALE" type="FLOAT">
            <short_desc>Magnetometer Z-axis scaling factor</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="SENS_ACC_XOFF" type="FLOAT">
            <short_desc>Accelerometer X-axis offset</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="SENS_ACC_YOFF" type="FLOAT">
            <short_desc>Accelerometer Y-axis offset</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="SENS_ACC_ZOFF" type="FLOAT">
            <short_desc>Accelerometer Z-axis offset</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="SENS_ACC_XSCALE" type="FLOAT">
            <short_desc>Accelerometer X-axis scaling factor</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="SENS_ACC_YSCALE" type="FLOAT">
            <short_desc>Accelerometer Y-axis scaling factor</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="SENS_ACC_ZSCALE" type="FLOAT">
            <short_desc>Accelerometer Z-axis scaling factor</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="SENS_DPRES_OFF" type="FLOAT">
            <short_desc>Differential pressure sensor offset</short_desc>
            <long_desc>The offset (zero-reading) in Pascal</long_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="SENS_DPRES_ANSC" type="FLOAT">
            <short_desc>Differential pressure sensor analog scaling</short_desc>
            <long_desc>Pick the appropriate scaling from the datasheet.
                this number defines the (linear) conversion from voltage
                to Pascal (pa). For the MPXV7002DP this is 1000.
                NOTE: If the sensor always registers zero, try switching
                the static and dynamic tubes.</long_desc>
            <default>0</default>
        </parameter>
        <parameter name="SENS_BARO_QNH" type="FLOAT">
            <short_desc>QNH for barometer</short_desc>
            <default>1013.25</default>
            <min>500</min>
            <max>1500</max>
            <unit>hPa</unit>
        </parameter>
        <parameter name="SENS_BOARD_ROT" type="INT32">
            <short_desc>Board rotation</short_desc>
            <long_desc>This parameter defines the rotation of the FMU board relative to the platform.
                Possible values are:
                0 = No rotation
                1 = Yaw 45°
                2 = Yaw 90°
                3 = Yaw 135°
                4 = Yaw 180°
                5 = Yaw 225°
                6 = Yaw 270°
                7 = Yaw 315°
                8 = Roll 180°
                9 = Roll 180°, Yaw 45°
                10 = Roll 180°, Yaw 90°
                11 = Roll 180°, Yaw 135°
                12 = Pitch 180°
                13 = Roll 180°, Yaw 225°
                14 = Roll 180°, Yaw 270°
                15 = Roll 180°, Yaw 315°
                16 = Roll 90°
                17 = Roll 90°, Yaw 45°
                18 = Roll 90°, Yaw 90°
                19 = Roll 90°, Yaw 135°
                20 = Roll 270°
                21 = Roll 270°, Yaw 45°
                22 = Roll 270°, Yaw 90°
                23 = Roll 270°, Yaw 135°
                24 = Pitch 90°
                25 = Pitch 270°</long_desc>
            <default>0</default>
        </parameter>
        <parameter name="SENS_BOARD_Y_OFF" type="FLOAT">
            <short_desc>Board rotation Y (Pitch) offset</short_desc>
            <long_desc>This parameter defines a rotational offset in degrees around the Y (Pitch) axis. It allows the user
                to fine tune the board offset in the event of misalignment.</long_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="SENS_BOARD_X_OFF" type="FLOAT">
            <short_desc>Board rotation X (Roll) offset</short_desc>
            <long_desc>This parameter defines a rotational offset in degrees around the X (Roll) axis It allows the user
                to fine tune the board offset in the event of misalignment.</long_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="SENS_BOARD_Z_OFF" type="FLOAT">
            <short_desc>Board rotation Z (YAW) offset</short_desc>
            <long_desc>This parameter defines a rotational offset in degrees around the Z (Yaw) axis. It allows the user
                to fine tune the board offset in the event of misalignment.</long_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="SENS_EXT_MAG_ROT" type="INT32">
            <short_desc>External magnetometer rotation</short_desc>
            <long_desc>This parameter defines the rotation of the external magnetometer relative
                to the platform (not relative to the FMU).
                See SENS_BOARD_ROT for possible values.</long_desc>
            <default>0</default>
        </parameter>
        <parameter name="SENS_EXT_MAG" type="INT32">
            <short_desc>Set usage of external magnetometer</short_desc>
            <long_desc>* Set to 0 (default) to auto-detect (will try to get the external as primary)
                * Set to 1 to force the external magnetometer as primary
                * Set to 2 to force the internal magnetometer as primary</long_desc>
            <default>0</default>
            <min>0</min>
            <max>2</max>
        </parameter>
    </group>
    <group name="System">
        <parameter name="SYS_AUTOSTART" type="INT32">
            <short_desc>Auto-start script index</short_desc>
            <long_desc>Defines the auto-start script used to bootstrap the system.</long_desc>
            <default>0</default>
        </parameter>
        <parameter name="SYS_AUTOCONFIG" type="INT32">
            <short_desc>Automatically configure default values</short_desc>
            <long_desc>Set to 1 to set platform-specific parameters to their default
                values on next system startup.</long_desc>
            <default>0</default>
            <min>0</min>
            <max>1</max>
        </parameter>
        <parameter name="SYS_USE_IO" type="INT32">
            <short_desc>Set usage of IO board</short_desc>
            <long_desc>Can be used to use a standard startup script but with a FMU only set-up. Set to 0 to force the FMU only set-up.</long_desc>
            <default>1</default>
            <min>0</min>
            <max>1</max>
        </parameter>
        <parameter name="SYS_RESTART_TYPE" type="INT32">
            <short_desc>Set restart type</short_desc>
            <long_desc>Set by px4io to indicate type of restart</long_desc>
            <default>2</default>
            <min>0</min>
            <max>2</max>
        </parameter>
    </group>
    <group name="UAVCAN">
        <parameter name="UAVCAN_ENABLE" type="INT32">
            <short_desc>Enable UAVCAN</short_desc>
            <long_desc>Enables support for UAVCAN-interfaced actuators and sensors.</long_desc>
            <default>0</default>
            <min>0</min>
            <max>1</max>
        </parameter>
        <parameter name="UAVCAN_NODE_ID" type="INT32">
            <short_desc>UAVCAN Node ID</short_desc>
            <long_desc>Read the specs at http://uavcan.org to learn more about Node ID.</long_desc>
            <default>1</default>
            <min>1</min>
            <max>125</max>
        </parameter>
        <parameter name="UAVCAN_BITRATE" type="INT32">
            <short_desc>UAVCAN CAN bus bitrate</short_desc>
            <default>1000000</default>
            <min>20000</min>
            <max>1000000</max>
        </parameter>
    </group>
    <group name="attitude_ekf">
        <parameter name="EKF_ATT_V3_Q0" type="FLOAT">
            <short_desc>Body angular rate process noise</short_desc>
            <default>1e-4</default>
        </parameter>
        <parameter name="EKF_ATT_V3_Q1" type="FLOAT">
            <short_desc>Body angular acceleration process noise</short_desc>
            <default>0.08</default>
        </parameter>
        <parameter name="EKF_ATT_V3_Q2" type="FLOAT">
            <short_desc>Acceleration process noise</short_desc>
            <default>0.009</default>
        </parameter>
        <parameter name="EKF_ATT_V3_Q3" type="FLOAT">
            <short_desc>Magnet field vector process noise</short_desc>
            <default>0.005</default>
        </parameter>
        <parameter name="EKF_ATT_V4_R0" type="FLOAT">
            <short_desc>Gyro measurement noise</short_desc>
            <default>0.0008</default>
        </parameter>
        <parameter name="EKF_ATT_V4_R1" type="FLOAT">
            <short_desc>Accel measurement noise</short_desc>
            <default>10000.0</default>
        </parameter>
        <parameter name="EKF_ATT_V4_R2" type="FLOAT">
            <short_desc>Mag measurement noise</short_desc>
            <default>100.0</default>
        </parameter>
        <parameter name="ATT_J11" type="FLOAT">
            <short_desc>Moment of inertia matrix diagonal entry (1, 1)</short_desc>
            <default>0.0018</default>
            <unit>kg*m^2</unit>
        </parameter>
        <parameter name="ATT_J22" type="FLOAT">
            <short_desc>Moment of inertia matrix diagonal entry (2, 2)</short_desc>
            <default>0.0018</default>
            <unit>kg*m^2</unit>
        </parameter>
        <parameter name="ATT_J33" type="FLOAT">
            <short_desc>Moment of inertia matrix diagonal entry (3, 3)</short_desc>
            <default>0.0037</default>
            <unit>kg*m^2</unit>
        </parameter>
        <parameter name="ATT_J_EN" type="INT32">
            <short_desc>Moment of inertia enabled in estimator</short_desc>
            <long_desc>If set to != 0 the moment of inertia will be used in the estimator</long_desc>
            <default>0</default>
            <min>0</min>
            <max>1</max>
        </parameter>
    </group>
    <group name="commander">
        <parameter name="COM_DL_LOSS_EN" type="INT32">
            <short_desc>Datalink loss mode enabled</short_desc>
            <long_desc>Set to 1 to enable actions triggered when the datalink is lost.</long_desc>
            <default>0</default>
            <min>0</min>
            <max>1</max>
        </parameter>
        <parameter name="COM_DL_LOSS_T" type="INT32">
            <short_desc>After this amount of seconds without datalink the data link lost mode triggers</short_desc>
            <default>10</default>
            <min>0</min>
            <max>30</max>
            <unit>second</unit>
        </parameter>
        <parameter name="COM_DL_REG_T" type="INT32">
            <short_desc>After a data link loss: after this this amount of seconds with a healthy datalink the 'datalink loss'
                flag is set back to false</short_desc>
            <default>0</default>
            <min>0</min>
            <max>30</max>
            <unit>second</unit>
        </parameter>
        <parameter name="COM_EF_THROT" type="FLOAT">
            <short_desc>Engine failure triggers only above this throttle value</short_desc>
            <default>0.5</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="COM_EF_C2T" type="FLOAT">
            <short_desc>Engine failure triggers only below this current/throttle value</short_desc>
            <default>5.0</default>
            <min>0.0</min>
            <max>7.0</max>
        </parameter>
        <parameter name="COM_EF_TIME" type="FLOAT">
            <short_desc>Engine failure triggers only if the throttle threshold and the
                current to throttle threshold are violated for this time</short_desc>
            <default>10.0</default>
            <min>0.0</min>
            <max>7.0</max>
            <unit>second</unit>
        </parameter>
        <parameter name="COM_RC_LOSS_T" type="FLOAT">
            <short_desc>After this amount of seconds without RC connection the rc lost flag is set to true</short_desc>
            <default>0.5</default>
            <min>0</min>
            <max>35</max>
2045
            <unit>seconds</unit>
Don Gagne's avatar
Don Gagne committed
2046 2047 2048 2049 2050 2051 2052 2053 2054 2055 2056 2057 2058 2059 2060 2061 2062 2063 2064 2065 2066 2067 2068 2069 2070 2071 2072 2073 2074 2075 2076 2077 2078 2079 2080 2081 2082 2083 2084 2085 2086 2087 2088 2089 2090 2091 2092 2093 2094 2095 2096 2097 2098 2099 2100 2101 2102 2103 2104 2105 2106 2107 2108 2109 2110 2111 2112 2113 2114 2115 2116 2117 2118 2119 2120 2121 2122 2123 2124 2125 2126 2127 2128 2129 2130 2131 2132 2133 2134 2135 2136 2137 2138 2139 2140 2141 2142 2143 2144 2145 2146 2147 2148 2149 2150 2151 2152 2153 2154 2155 2156 2157 2158 2159 2160 2161 2162 2163 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174 2175 2176 2177 2178 2179 2180 2181 2182 2183 2184 2185 2186 2187 2188 2189 2190 2191 2192 2193 2194 2195 2196 2197 2198 2199 2200 2201 2202 2203 2204 2205 2206 2207 2208 2209 2210 2211 2212 2213 2214 2215 2216 2217 2218 2219 2220 2221 2222 2223 2224 2225 2226 2227 2228 2229 2230 2231 2232 2233 2234 2235 2236 2237 2238 2239 2240 2241 2242 2243 2244 2245 2246 2247 2248 2249 2250 2251 2252 2253 2254 2255 2256 2257 2258 2259 2260 2261 2262 2263 2264 2265 2266 2267 2268 2269 2270 2271 2272 2273 2274 2275 2276 2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287 2288 2289 2290 2291 2292 2293 2294 2295 2296 2297 2298 2299 2300 2301 2302 2303 2304 2305 2306 2307 2308 2309 2310 2311 2312 2313 2314 2315 2316 2317 2318 2319 2320 2321 2322 2323 2324 2325 2326 2327 2328 2329 2330 2331 2332 2333 2334 2335 2336 2337 2338 2339 2340 2341 2342 2343 2344 2345 2346 2347 2348 2349 2350 2351 2352 2353 2354 2355 2356 2357 2358 2359 2360 2361 2362 2363 2364 2365 2366 2367 2368 2369 2370 2371 2372 2373 2374 2375 2376 2377 2378 2379 2380 2381 2382 2383 2384 2385 2386 2387 2388 2389 2390 2391 2392 2393 2394 2395 2396 2397 2398 2399 2400 2401 2402 2403 2404 2405 2406 2407 2408 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420 2421 2422 2423 2424 2425 2426 2427 2428 2429 2430 2431 2432 2433 2434 2435 2436 2437 2438 2439 2440 2441 2442 2443 2444 2445 2446 2447 2448 2449 2450 2451 2452 2453 2454 2455 2456 2457 2458 2459 2460 2461 2462 2463 2464 2465 2466 2467 2468 2469 2470 2471 2472 2473 2474 2475 2476 2477 2478 2479 2480 2481 2482 2483 2484 2485 2486 2487 2488 2489 2490 2491 2492 2493 2494 2495 2496 2497 2498 2499 2500 2501 2502 2503 2504 2505 2506 2507 2508 2509 2510 2511 2512 2513 2514 2515 2516 2517 2518 2519 2520 2521 2522 2523 2524 2525 2526 2527 2528 2529 2530 2531 2532 2533 2534 2535 2536 2537 2538 2539 2540 2541 2542 2543 2544 2545 2546 2547 2548 2549 2550 2551 2552 2553 2554 2555 2556 2557 2558 2559 2560 2561 2562 2563 2564 2565 2566 2567 2568 2569 2570 2571 2572 2573 2574 2575 2576 2577 2578 2579 2580 2581 2582 2583 2584 2585 2586 2587 2588 2589 2590 2591 2592 2593 2594 2595 2596 2597 2598 2599 2600 2601 2602 2603 2604 2605 2606 2607 2608 2609 2610 2611 2612 2613 2614 2615 2616 2617 2618 2619 2620 2621 2622 2623 2624 2625 2626 2627 2628 2629 2630 2631 2632 2633 2634 2635 2636 2637 2638 2639 2640 2641 2642 2643 2644 2645 2646 2647 2648 2649 2650 2651 2652 2653 2654 2655 2656 2657 2658 2659 2660 2661 2662 2663 2664 2665 2666 2667 2668 2669 2670 2671 2672 2673 2674 2675 2676 2677 2678 2679 2680 2681 2682 2683 2684 2685 2686 2687 2688 2689 2690 2691 2692 2693 2694 2695 2696 2697 2698 2699 2700 2701 2702 2703 2704 2705 2706 2707 2708 2709 2710 2711 2712 2713 2714 2715 2716 2717 2718 2719 2720 2721 2722 2723 2724 2725 2726 2727 2728 2729 2730 2731 2732 2733 2734 2735 2736 2737 2738 2739 2740 2741 2742 2743 2744 2745 2746 2747 2748 2749 2750 2751 2752 2753 2754 2755 2756 2757 2758 2759 2760 2761 2762 2763 2764 2765 2766 2767 2768 2769 2770 2771 2772 2773 2774 2775 2776 2777 2778 2779 2780 2781 2782 2783 2784 2785 2786 2787 2788 2789 2790 2791 2792 2793 2794 2795 2796 2797 2798 2799 2800 2801 2802 2803 2804 2805 2806 2807 2808 2809 2810 2811 2812 2813 2814 2815 2816 2817 2818 2819 2820 2821 2822 2823 2824 2825 2826 2827 2828 2829 2830 2831 2832 2833 2834 2835 2836 2837 2838 2839 2840 2841 2842 2843 2844 2845 2846 2847 2848 2849 2850 2851 2852 2853 2854 2855 2856 2857 2858 2859 2860 2861 2862 2863 2864 2865 2866 2867 2868 2869 2870 2871 2872 2873 2874 2875 2876 2877 2878 2879 2880 2881 2882 2883 2884 2885 2886 2887 2888 2889 2890 2891 2892 2893 2894 2895 2896 2897 2898 2899 2900 2901 2902 2903 2904 2905 2906 2907 2908 2909 2910 2911 2912 2913 2914 2915 2916 2917 2918 2919 2920 2921 2922 2923 2924 2925 2926 2927 2928 2929 2930 2931 2932 2933 2934 2935 2936 2937 2938 2939 2940 2941 2942 2943 2944 2945 2946 2947 2948 2949 2950 2951 2952 2953 2954 2955 2956 2957 2958 2959 2960 2961 2962 2963 2964 2965 2966 2967 2968 2969 2970 2971 2972 2973 2974 2975 2976 2977 2978 2979 2980 2981 2982 2983 2984 2985 2986 2987 2988 2989 2990 2991 2992 2993 2994 2995 2996 2997 2998 2999 3000 3001 3002 3003 3004 3005 3006 3007 3008 3009 3010 3011 3012 3013 3014 3015 3016 3017 3018 3019 3020 3021 3022 3023 3024 3025 3026 3027 3028 3029 3030 3031 3032 3033 3034 3035 3036 3037 3038
        </parameter>
    </group>
    <group name="mTECS">
        <parameter name="MT_ENABLED" type="INT32">
            <short_desc>mTECS enabled</short_desc>
            <long_desc>Set to 1 to enable mTECS</long_desc>
            <default>0</default>
            <min>0</min>
            <max>1</max>
        </parameter>
        <parameter name="MT_THR_FF" type="FLOAT">
            <short_desc>Total Energy Rate Control Feedforward
                Maps the total energy rate setpoint to the throttle setpoint</short_desc>
            <default>0.7</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_THR_P" type="FLOAT">
            <short_desc>Total Energy Rate Control P
                Maps the total energy rate error to the throttle setpoint</short_desc>
            <default>0.1</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_THR_I" type="FLOAT">
            <short_desc>Total Energy Rate Control I
                Maps the integrated total energy rate to the throttle setpoint</short_desc>
            <default>0.25</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_THR_OFF" type="FLOAT">
            <short_desc>Total Energy Rate Control Offset (Cruise throttle sp)</short_desc>
            <default>0.7</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_PIT_FF" type="FLOAT">
            <short_desc>Energy Distribution Rate Control Feedforward
                Maps the energy distribution rate setpoint to the pitch setpoint</short_desc>
            <default>0.4</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_PIT_P" type="FLOAT">
            <short_desc>Energy Distribution Rate Control P
                Maps the energy distribution rate error to the pitch setpoint</short_desc>
            <default>0.03</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_PIT_I" type="FLOAT">
            <short_desc>Energy Distribution Rate Control I
                Maps the integrated energy distribution rate error to the pitch setpoint</short_desc>
            <default>0.03</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_PIT_OFF" type="FLOAT">
            <short_desc>Total Energy Distribution Offset (Cruise pitch sp)</short_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_THR_MIN" type="FLOAT">
            <short_desc>Minimal Throttle Setpoint</short_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MT_THR_MAX" type="FLOAT">
            <short_desc>Maximal Throttle Setpoint</short_desc>
            <default>1.0</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MT_PIT_MIN" type="FLOAT">
            <short_desc>Minimal Pitch Setpoint in Degrees</short_desc>
            <default>-45.0</default>
            <min>-90.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MT_PIT_MAX" type="FLOAT">
            <short_desc>Maximal Pitch Setpoint in Degrees</short_desc>
            <default>20.0</default>
            <min>-90.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MT_ALT_LP" type="FLOAT">
            <short_desc>Lowpass (cutoff freq.) for altitude</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="MT_FPA_LP" type="FLOAT">
            <short_desc>Lowpass (cutoff freq.) for the flight path angle</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="MT_FPA_P" type="FLOAT">
            <short_desc>P gain for the altitude control
                Maps the altitude error to the flight path angle setpoint</short_desc>
            <default>0.3</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_FPA_D" type="FLOAT">
            <short_desc>D gain for the altitude control
                Maps the change of altitude error to the flight path angle setpoint</short_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_FPA_D_LP" type="FLOAT">
            <short_desc>Lowpass for FPA error derivative calculation (see MT_FPA_D)</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="MT_FPA_MIN" type="FLOAT">
            <short_desc>Minimal flight path angle setpoint</short_desc>
            <default>-20.0</default>
            <min>-90.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MT_FPA_MAX" type="FLOAT">
            <short_desc>Maximal flight path angle setpoint</short_desc>
            <default>30.0</default>
            <min>-90.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MT_A_LP" type="FLOAT">
            <short_desc>Lowpass (cutoff freq.) for airspeed</short_desc>
            <default>0.5</default>
        </parameter>
        <parameter name="MT_AD_LP" type="FLOAT">
            <short_desc>Airspeed derivative calculation lowpass</short_desc>
            <default>0.5</default>
        </parameter>
        <parameter name="MT_ACC_P" type="FLOAT">
            <short_desc>P gain for the airspeed control
                Maps the airspeed error to the acceleration setpoint</short_desc>
            <default>0.3</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_ACC_D" type="FLOAT">
            <short_desc>D gain for the airspeed control
                Maps the change of airspeed error to the acceleration setpoint</short_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_ACC_D_LP" type="FLOAT">
            <short_desc>Lowpass for ACC error derivative calculation (see MT_ACC_D)</short_desc>
            <default>0.5</default>
        </parameter>
        <parameter name="MT_ACC_MIN" type="FLOAT">
            <short_desc>Minimal acceleration (air)</short_desc>
            <default>-40.0</default>
            <unit>m/s^2</unit>
        </parameter>
        <parameter name="MT_ACC_MAX" type="FLOAT">
            <short_desc>Maximal acceleration (air)</short_desc>
            <default>40.0</default>
            <unit>m/s^2</unit>
        </parameter>
        <parameter name="MT_TKF_THR_MIN" type="FLOAT">
            <short_desc>Minimal throttle during takeoff</short_desc>
            <default>1.0</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MT_TKF_THR_MAX" type="FLOAT">
            <short_desc>Maximal throttle during takeoff</short_desc>
            <default>1.0</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MT_TKF_PIT_MIN" type="FLOAT">
            <short_desc>Minimal pitch during takeoff</short_desc>
            <default>0.0</default>
            <min>-90.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MT_TKF_PIT_MAX" type="FLOAT">
            <short_desc>Maximal pitch during takeoff</short_desc>
            <default>45.0</default>
            <min>-90.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MT_USP_THR_MIN" type="FLOAT">
            <short_desc>Minimal throttle in underspeed mode</short_desc>
            <default>1.0</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MT_USP_THR_MAX" type="FLOAT">
            <short_desc>Maximal throttle in underspeed mode</short_desc>
            <default>1.0</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MT_USP_PIT_MIN" type="FLOAT">
            <short_desc>Minimal pitch in underspeed mode</short_desc>
            <default>-45.0</default>
            <min>-90.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MT_USP_PIT_MAX" type="FLOAT">
            <short_desc>Maximal pitch in underspeed mode</short_desc>
            <default>0.0</default>
            <min>-90.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MT_LND_THR_MIN" type="FLOAT">
            <short_desc>Minimal throttle in landing mode (only last phase of landing)</short_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MT_LND_THR_MAX" type="FLOAT">
            <short_desc>Maximal throttle in landing mode (only last phase of landing)</short_desc>
            <default>0.0</default>
            <min>0.0</min>
            <max>1.0</max>
        </parameter>
        <parameter name="MT_LND_PIT_MIN" type="FLOAT">
            <short_desc>Minimal pitch in landing mode</short_desc>
            <default>-5.0</default>
            <min>-90.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MT_LND_PIT_MAX" type="FLOAT">
            <short_desc>Maximal pitch in landing mode</short_desc>
            <default>15.0</default>
            <min>-90.0</min>
            <max>90.0</max>
            <unit>deg</unit>
        </parameter>
        <parameter name="MT_THR_I_MAX" type="FLOAT">
            <short_desc>Integrator Limit for Total Energy Rate Control</short_desc>
            <default>10.0</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
        <parameter name="MT_PIT_I_MAX" type="FLOAT">
            <short_desc>Integrator Limit for Energy Distribution Rate Control</short_desc>
            <default>10.0</default>
            <min>0.0</min>
            <max>10.0</max>
        </parameter>
    </group>
    <group name="Miscellaneous">
        <parameter name="EXFW_HDNG_P" type="FLOAT">
            <short_desc>EXFW_HDNG_P</short_desc>
            <default>0.1</default>
        </parameter>
        <parameter name="EXFW_ROLL_P" type="FLOAT">
            <short_desc>EXFW_ROLL_P</short_desc>
            <default>0.2</default>
        </parameter>
        <parameter name="EXFW_PITCH_P" type="FLOAT">
            <short_desc>EXFW_PITCH_P</short_desc>
            <default>0.2</default>
        </parameter>
        <parameter name="FPE_LO_THRUST" type="FLOAT">
            <short_desc>FPE_LO_THRUST</short_desc>
            <default>0.4</default>
        </parameter>
        <parameter name="FPE_SONAR_LP_U" type="FLOAT">
            <short_desc>FPE_SONAR_LP_U</short_desc>
            <default>0.5</default>
        </parameter>
        <parameter name="FPE_SONAR_LP_L" type="FLOAT">
            <short_desc>FPE_SONAR_LP_L</short_desc>
            <default>0.2</default>
        </parameter>
        <parameter name="FPE_DEBUG" type="INT32">
            <short_desc>FPE_DEBUG</short_desc>
            <default>0</default>
        </parameter>
        <parameter name="FSC_S_P" type="FLOAT">
            <short_desc>FSC_S_P</short_desc>
            <default>0.1</default>
        </parameter>
        <parameter name="FSC_L_PITCH" type="FLOAT">
            <short_desc>FSC_L_PITCH</short_desc>
            <default>0.4</default>
        </parameter>
        <parameter name="FSC_L_ROLL" type="FLOAT">
            <short_desc>FSC_L_ROLL</short_desc>
            <default>0.4</default>
        </parameter>
        <parameter name="ATT_MAG_DECL" type="FLOAT">
            <short_desc>ATT_MAG_DECL</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="ATT_ACC_COMP" type="INT32">
            <short_desc>ATT_ACC_COMP</short_desc>
            <default>2</default>
        </parameter>
        <parameter name="SO3_COMP_KP" type="FLOAT">
            <short_desc>SO3_COMP_KP</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="SO3_COMP_KI" type="FLOAT">
            <short_desc>SO3_COMP_KI</short_desc>
            <default>0.05</default>
        </parameter>
        <parameter name="SO3_ROLL_OFFS" type="FLOAT">
            <short_desc>SO3_ROLL_OFFS</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="SO3_PITCH_OFFS" type="FLOAT">
            <short_desc>SO3_PITCH_OFFS</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="SO3_YAW_OFFS" type="FLOAT">
            <short_desc>SO3_YAW_OFFS</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="TRIM_ROLL" type="FLOAT">
            <short_desc>TRIM_ROLL</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="TRIM_PITCH" type="FLOAT">
            <short_desc>TRIM_PITCH</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="TRIM_YAW" type="FLOAT">
            <short_desc>TRIM_YAW</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="TEST_MIN" type="FLOAT">
            <short_desc>TEST_MIN</short_desc>
            <default>-1.0</default>
        </parameter>
        <parameter name="TEST_MAX" type="FLOAT">
            <short_desc>TEST_MAX</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="TEST_TRIM" type="FLOAT">
            <short_desc>TEST_TRIM</short_desc>
            <default>0.5</default>
        </parameter>
        <parameter name="TEST_HP" type="FLOAT">
            <short_desc>TEST_HP</short_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="TEST_LP" type="FLOAT">
            <short_desc>TEST_LP</short_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="TEST_P" type="FLOAT">
            <short_desc>TEST_P</short_desc>
            <default>0.2</default>
        </parameter>
        <parameter name="TEST_I" type="FLOAT">
            <short_desc>TEST_I</short_desc>
            <default>0.1</default>
        </parameter>
        <parameter name="TEST_I_MAX" type="FLOAT">
            <short_desc>TEST_I_MAX</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="TEST_D" type="FLOAT">
            <short_desc>TEST_D</short_desc>
            <default>0.01</default>
        </parameter>
        <parameter name="TEST_D_LP" type="FLOAT">
            <short_desc>TEST_D_LP</short_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="TEST_MEAN" type="FLOAT">
            <short_desc>TEST_MEAN</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="TEST_DEV" type="FLOAT">
            <short_desc>TEST_DEV</short_desc>
            <default>2.0</default>
        </parameter>
        <parameter name="FWB_P_LP" type="FLOAT">
            <short_desc>FWB_P_LP</short_desc>
            <default>300.0</default>
        </parameter>
        <parameter name="FWB_Q_LP" type="FLOAT">
            <short_desc>FWB_Q_LP</short_desc>
            <default>300.0</default>
        </parameter>
        <parameter name="FWB_R_LP" type="FLOAT">
            <short_desc>FWB_R_LP</short_desc>
            <default>300.0</default>
        </parameter>
        <parameter name="FWB_R_HP" type="FLOAT">
            <short_desc>FWB_R_HP</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="FWB_P2AIL" type="FLOAT">
            <short_desc>FWB_P2AIL</short_desc>
            <default>0.3</default>
        </parameter>
        <parameter name="FWB_Q2ELV" type="FLOAT">
            <short_desc>FWB_Q2ELV</short_desc>
            <default>0.1</default>
        </parameter>
        <parameter name="FWB_R2RDR" type="FLOAT">
            <short_desc>FWB_R2RDR</short_desc>
            <default>0.1</default>
        </parameter>
        <parameter name="FWB_PSI2PHI" type="FLOAT">
            <short_desc>FWB_PSI2PHI</short_desc>
            <default>0.5</default>
        </parameter>
        <parameter name="FWB_PHI2P" type="FLOAT">
            <short_desc>FWB_PHI2P</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="FWB_PHI_LIM_MAX" type="FLOAT">
            <short_desc>FWB_PHI_LIM_MAX</short_desc>
            <default>0.3</default>
        </parameter>
        <parameter name="FWB_V2THE_P" type="FLOAT">
            <short_desc>FWB_V2THE_P</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="FWB_V2THE_I" type="FLOAT">
            <short_desc>FWB_V2THE_I</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_V2THE_D" type="FLOAT">
            <short_desc>FWB_V2THE_D</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_V2THE_D_LP" type="FLOAT">
            <short_desc>FWB_V2THE_D_LP</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_V2THE_I_MAX" type="FLOAT">
            <short_desc>FWB_V2THE_I_MAX</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_THE_MIN" type="FLOAT">
            <short_desc>FWB_THE_MIN</short_desc>
            <default>-0.5</default>
        </parameter>
        <parameter name="FWB_THE_MAX" type="FLOAT">
            <short_desc>FWB_THE_MAX</short_desc>
            <default>0.5</default>
        </parameter>
        <parameter name="FWB_THE2Q_P" type="FLOAT">
            <short_desc>FWB_THE2Q_P</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="FWB_THE2Q_I" type="FLOAT">
            <short_desc>FWB_THE2Q_I</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_THE2Q_D" type="FLOAT">
            <short_desc>FWB_THE2Q_D</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_THE2Q_D_LP" type="FLOAT">
            <short_desc>FWB_THE2Q_D_LP</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_THE2Q_I_MAX" type="FLOAT">
            <short_desc>FWB_THE2Q_I_MAX</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_H2THR_P" type="FLOAT">
            <short_desc>FWB_H2THR_P</short_desc>
            <default>0.01</default>
        </parameter>
        <parameter name="FWB_H2THR_I" type="FLOAT">
            <short_desc>FWB_H2THR_I</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_H2THR_D" type="FLOAT">
            <short_desc>FWB_H2THR_D</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_H2THR_D_LP" type="FLOAT">
            <short_desc>FWB_H2THR_D_LP</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_H2THR_I_MAX" type="FLOAT">
            <short_desc>FWB_H2THR_I_MAX</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_XT2YAW_MAX" type="FLOAT">
            <short_desc>FWB_XT2YAW_MAX</short_desc>
            <default>1.57</default>
        </parameter>
        <parameter name="FWB_XT2YAW" type="FLOAT">
            <short_desc>FWB_XT2YAW</short_desc>
            <default>0.005</default>
        </parameter>
        <parameter name="FWB_V_MIN" type="FLOAT">
            <short_desc>FWB_V_MIN</short_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="FWB_V_CMD" type="FLOAT">
            <short_desc>FWB_V_CMD</short_desc>
            <default>12.0</default>
        </parameter>
        <parameter name="FWB_V_MAX" type="FLOAT">
            <short_desc>FWB_V_MAX</short_desc>
            <default>16.0</default>
        </parameter>
        <parameter name="FWB_CR_MAX" type="FLOAT">
            <short_desc>FWB_CR_MAX</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="FWB_CR2THR_P" type="FLOAT">
            <short_desc>FWB_CR2THR_P</short_desc>
            <default>0.01</default>
        </parameter>
        <parameter name="FWB_CR2THR_I" type="FLOAT">
            <short_desc>FWB_CR2THR_I</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_CR2THR_D" type="FLOAT">
            <short_desc>FWB_CR2THR_D</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_CR2THR_D_LP" type="FLOAT">
            <short_desc>FWB_CR2THR_D_LP</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_CR2THR_I_MAX" type="FLOAT">
            <short_desc>FWB_CR2THR_I_MAX</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="FWB_TRIM_THR" type="FLOAT">
            <short_desc>FWB_TRIM_THR</short_desc>
            <default>0.8</default>
        </parameter>
        <parameter name="FWB_TRIM_V" type="FLOAT">
            <short_desc>FWB_TRIM_V</short_desc>
            <default>12.0</default>
        </parameter>
        <parameter name="FW_FLARE_PMIN" type="FLOAT">
            <short_desc>Flare, minimum pitch</short_desc>
            <long_desc>Minimum pitch during flare, a positive sign means nose up
                Applied once FW_LND_TLALT is reached</long_desc>
            <default>2.5</default>
        </parameter>
        <parameter name="FW_FLARE_PMAX" type="FLOAT">
            <short_desc>Flare, maximum pitch</short_desc>
            <long_desc>Maximum pitch during flare, a positive sign means nose up
                Applied once FW_LND_TLALT is reached</long_desc>
            <default>15.0</default>
        </parameter>
        <parameter name="SEG_TH2V_P" type="FLOAT">
            <short_desc>SEG_TH2V_P</short_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="SEG_TH2V_I" type="FLOAT">
            <short_desc>SEG_TH2V_I</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="SEG_TH2V_I_MAX" type="FLOAT">
            <short_desc>SEG_TH2V_I_MAX</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="SEG_Q2V" type="FLOAT">
            <short_desc>SEG_Q2V</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC3_MIN" type="FLOAT">
            <short_desc>RC3_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC3_TRIM" type="FLOAT">
            <short_desc>RC3_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC3_MAX" type="FLOAT">
            <short_desc>RC3_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC3_REV" type="FLOAT">
            <short_desc>RC3_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC3_DZ" type="FLOAT">
            <short_desc>RC3_DZ</short_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="RC4_MIN" type="FLOAT">
            <short_desc>RC4_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC4_TRIM" type="FLOAT">
            <short_desc>RC4_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC4_MAX" type="FLOAT">
            <short_desc>RC4_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC4_REV" type="FLOAT">
            <short_desc>RC4_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC4_DZ" type="FLOAT">
            <short_desc>RC4_DZ</short_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="RC5_MIN" type="FLOAT">
            <short_desc>RC5_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC5_TRIM" type="FLOAT">
            <short_desc>RC5_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC5_MAX" type="FLOAT">
            <short_desc>RC5_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC5_REV" type="FLOAT">
            <short_desc>RC5_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC5_DZ" type="FLOAT">
            <short_desc>RC5_DZ</short_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="RC6_MIN" type="FLOAT">
            <short_desc>RC6_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC6_TRIM" type="FLOAT">
            <short_desc>RC6_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC6_MAX" type="FLOAT">
            <short_desc>RC6_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC6_REV" type="FLOAT">
            <short_desc>RC6_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC6_DZ" type="FLOAT">
            <short_desc>RC6_DZ</short_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="RC7_MIN" type="FLOAT">
            <short_desc>RC7_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC7_TRIM" type="FLOAT">
            <short_desc>RC7_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC7_MAX" type="FLOAT">
            <short_desc>RC7_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC7_REV" type="FLOAT">
            <short_desc>RC7_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC7_DZ" type="FLOAT">
            <short_desc>RC7_DZ</short_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="RC8_MIN" type="FLOAT">
            <short_desc>RC8_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC8_TRIM" type="FLOAT">
            <short_desc>RC8_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC8_MAX" type="FLOAT">
            <short_desc>RC8_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC8_REV" type="FLOAT">
            <short_desc>RC8_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC8_DZ" type="FLOAT">
            <short_desc>RC8_DZ</short_desc>
            <default>10.0</default>
        </parameter>
        <parameter name="RC9_MIN" type="FLOAT">
            <short_desc>RC9_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC9_TRIM" type="FLOAT">
            <short_desc>RC9_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC9_MAX" type="FLOAT">
            <short_desc>RC9_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC9_REV" type="FLOAT">
            <short_desc>RC9_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC9_DZ" type="FLOAT">
            <short_desc>RC9_DZ</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="RC10_MIN" type="FLOAT">
            <short_desc>RC10_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC10_TRIM" type="FLOAT">
            <short_desc>RC10_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC10_MAX" type="FLOAT">
            <short_desc>RC10_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC10_REV" type="FLOAT">
            <short_desc>RC10_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC10_DZ" type="FLOAT">
            <short_desc>RC10_DZ</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="RC11_MIN" type="FLOAT">
            <short_desc>RC11_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC11_TRIM" type="FLOAT">
            <short_desc>RC11_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC11_MAX" type="FLOAT">
            <short_desc>RC11_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC11_REV" type="FLOAT">
            <short_desc>RC11_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC11_DZ" type="FLOAT">
            <short_desc>RC11_DZ</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="RC12_MIN" type="FLOAT">
            <short_desc>RC12_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC12_TRIM" type="FLOAT">
            <short_desc>RC12_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC12_MAX" type="FLOAT">
            <short_desc>RC12_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC12_REV" type="FLOAT">
            <short_desc>RC12_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC12_DZ" type="FLOAT">
            <short_desc>RC12_DZ</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="RC13_MIN" type="FLOAT">
            <short_desc>RC13_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC13_TRIM" type="FLOAT">
            <short_desc>RC13_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC13_MAX" type="FLOAT">
            <short_desc>RC13_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC13_REV" type="FLOAT">
            <short_desc>RC13_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC13_DZ" type="FLOAT">
            <short_desc>RC13_DZ</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="RC14_MIN" type="FLOAT">
            <short_desc>RC14_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC14_TRIM" type="FLOAT">
            <short_desc>RC14_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC14_MAX" type="FLOAT">
            <short_desc>RC14_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC14_REV" type="FLOAT">
            <short_desc>RC14_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC14_DZ" type="FLOAT">
            <short_desc>RC14_DZ</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="RC15_MIN" type="FLOAT">
            <short_desc>RC15_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC15_TRIM" type="FLOAT">
            <short_desc>RC15_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC15_MAX" type="FLOAT">
            <short_desc>RC15_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC15_REV" type="FLOAT">
            <short_desc>RC15_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC15_DZ" type="FLOAT">
            <short_desc>RC15_DZ</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="RC16_MIN" type="FLOAT">
            <short_desc>RC16_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC16_TRIM" type="FLOAT">
            <short_desc>RC16_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC16_MAX" type="FLOAT">
            <short_desc>RC16_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC16_REV" type="FLOAT">
            <short_desc>RC16_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC16_DZ" type="FLOAT">
            <short_desc>RC16_DZ</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="RC17_MIN" type="FLOAT">
            <short_desc>RC17_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC17_TRIM" type="FLOAT">
            <short_desc>RC17_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC17_MAX" type="FLOAT">
            <short_desc>RC17_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC17_REV" type="FLOAT">
            <short_desc>RC17_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC17_DZ" type="FLOAT">
            <short_desc>RC17_DZ</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="RC18_MIN" type="FLOAT">
            <short_desc>RC18_MIN</short_desc>
            <default>1000</default>
        </parameter>
        <parameter name="RC18_TRIM" type="FLOAT">
            <short_desc>RC18_TRIM</short_desc>
            <default>1500</default>
        </parameter>
        <parameter name="RC18_MAX" type="FLOAT">
            <short_desc>RC18_MAX</short_desc>
            <default>2000</default>
        </parameter>
        <parameter name="RC18_REV" type="FLOAT">
            <short_desc>RC18_REV</short_desc>
            <default>1.0</default>
        </parameter>
        <parameter name="RC18_DZ" type="FLOAT">
            <short_desc>RC18_DZ</short_desc>
            <default>0.0</default>
        </parameter>
        <parameter name="RC_RL1_DSM_VCC" type="INT32">
            <short_desc>RC_RL1_DSM_VCC</short_desc>
            <default>0</default>
        </parameter>
        <parameter name="RC_MAP_FAILSAFE" type="INT32">
            <short_desc>Failsafe channel mapping</short_desc>
            <long_desc>The RC mapping index indicates which channel is used for failsafe
                If 0, whichever channel is mapped to throttle is used
                otherwise the value indicates the specific rc channel to use</long_desc>
            <default>0</default>
            <min>0</min>
            <max>18</max>
        </parameter>
        <parameter name="RC_ASSIST_TH" type="FLOAT">
            <short_desc>Threshold for selecting assist mode</short_desc>
            <long_desc>min:-1
                max:+1
                0-1 indicate where in the full channel range the threshold sits
                0 : min
                1 : max
                sign indicates polarity of comparison
                positive : true when channel&gt;th
                negative : true when channel&lt;th</long_desc>
            <default>0.25</default>
        </parameter>
        <parameter name="RC_AUTO_TH" type="FLOAT">
            <short_desc>Threshold for selecting auto mode</short_desc>
            <long_desc>min:-1
                max:+1
                0-1 indicate where in the full channel range the threshold sits
                0 : min
                1 : max
                sign indicates polarity of comparison
                positive : true when channel&gt;th
                negative : true when channel&lt;th</long_desc>
            <default>0.75</default>
        </parameter>
        <parameter name="RC_POSCTL_TH" type="FLOAT">
            <short_desc>Threshold for selecting posctl mode</short_desc>
            <long_desc>min:-1
                max:+1
                0-1 indicate where in the full channel range the threshold sits
                0 : min
                1 : max
                sign indicates polarity of comparison
                positive : true when channel&gt;th
                negative : true when channel&lt;th</long_desc>
            <default>0.5</default>
        </parameter>
        <parameter name="RC_RETURN_TH" type="FLOAT">
            <short_desc>Threshold for selecting return to launch mode</short_desc>
            <long_desc>min:-1
                max:+1
                0-1 indicate where in the full channel range the threshold sits
                0 : min
                1 : max
                sign indicates polarity of comparison
                positive : true when channel&gt;th
                negative : true when channel&lt;th</long_desc>
            <default>0.5</default>
        </parameter>
        <parameter name="RC_LOITER_TH" type="FLOAT">
            <short_desc>Threshold for selecting loiter mode</short_desc>
            <long_desc>min:-1
                max:+1
                0-1 indicate where in the full channel range the threshold sits
                0 : min
                1 : max
                sign indicates polarity of comparison
                positive : true when channel&gt;th
                negative : true when channel&lt;th</long_desc>
            <default>0.5</default>
        </parameter>
        <parameter name="RC_ACRO_TH" type="FLOAT">
            <short_desc>Threshold for selecting acro mode</short_desc>
            <long_desc>min:-1
                max:+1
                0-1 indicate where in the full channel range the threshold sits
                0 : min
                1 : max
                sign indicates polarity of comparison
                positive : true when channel&gt;th
                negative : true when channel&lt;th</long_desc>
            <default>0.5</default>
        </parameter>
        <parameter name="RC_OFFB_TH" type="FLOAT">
            <short_desc>Threshold for selecting offboard mode</short_desc>
            <long_desc>min:-1
                max:+1
                0-1 indicate where in the full channel range the threshold sits
                0 : min
                1 : max
                sign indicates polarity of comparison
                positive : true when channel&gt;th
                negative : true when channel&lt;th</long_desc>
            <default>0.5</default>
        </parameter>
    </group>
</parameters>