Commit 7e2a2f65 authored by PX4BuildBot's avatar PX4BuildBot

Update PX4 Firmware metadata Wed Nov 4 16:06:10 UTC 2020

parent cb8b124f
...@@ -3281,6 +3281,20 @@ but also ignore less noise</short_desc> ...@@ -3281,6 +3281,20 @@ but also ignore less noise</short_desc>
<value code="300">Radio Controller</value> <value code="300">Radio Controller</value>
</values> </values>
</parameter> </parameter>
<parameter name="GPS_1_PROTOCOL" default="1" type="INT32">
<short_desc>Protocol for Main GPS</short_desc>
<long_desc>Select the GPS protocol over serial. Auto-detection will probe all protocols, and thus is a bit slower.</long_desc>
<min>0</min>
<max>4</max>
<reboot_required>true</reboot_required>
<values>
<value code="0">Auto detect</value>
<value code="1">u-blox</value>
<value code="2">MTK</value>
<value code="3">Ashtech / Trimble</value>
<value code="4">Emlid Reach</value>
</values>
</parameter>
<parameter name="GPS_2_CONFIG" default="0" type="INT32"> <parameter name="GPS_2_CONFIG" default="0" type="INT32">
<short_desc>Serial Configuration for Secondary GPS</short_desc> <short_desc>Serial Configuration for Secondary GPS</short_desc>
<long_desc>Configure on which serial port to run Secondary GPS.</long_desc> <long_desc>Configure on which serial port to run Secondary GPS.</long_desc>
...@@ -3298,6 +3312,20 @@ but also ignore less noise</short_desc> ...@@ -3298,6 +3312,20 @@ but also ignore less noise</short_desc>
<value code="300">Radio Controller</value> <value code="300">Radio Controller</value>
</values> </values>
</parameter> </parameter>
<parameter name="GPS_2_PROTOCOL" default="1" type="INT32">
<short_desc>Protocol for Secondary GPS</short_desc>
<long_desc>Select the GPS protocol over serial. Auto-detection will probe all protocols, and thus is a bit slower.</long_desc>
<min>0</min>
<max>4</max>
<reboot_required>true</reboot_required>
<values>
<value code="0">Auto detect</value>
<value code="1">u-blox</value>
<value code="2">MTK</value>
<value code="3">Ashtech / Trimble</value>
<value code="4">Emlid Reach</value>
</values>
</parameter>
<parameter name="GPS_DUMP_COMM" default="0" type="INT32"> <parameter name="GPS_DUMP_COMM" default="0" type="INT32">
<short_desc>Dump GPS communication to a file</short_desc> <short_desc>Dump GPS communication to a file</short_desc>
<long_desc>If this is set to 1, all GPS communication data will be published via uORB, and written to the log file as gps_dump message.</long_desc> <long_desc>If this is set to 1, all GPS communication data will be published via uORB, and written to the log file as gps_dump message.</long_desc>
...@@ -3322,6 +3350,17 @@ but also ignore less noise</short_desc> ...@@ -3322,6 +3350,17 @@ but also ignore less noise</short_desc>
<value code="8">airborne with &lt;4g acceleration</value> <value code="8">airborne with &lt;4g acceleration</value>
</values> </values>
</parameter> </parameter>
<parameter name="GPS_UBX_MODE" default="0" type="INT32">
<short_desc>u-blox GPS Mode</short_desc>
<long_desc>Select the u-blox configuration setup. Most setups will use the default, including RTK and dual GPS without heading. The Heading mode requires 2 F9P devices to be attached. The main GPS will act as rover and output heading information, whereas the secondary will act as moving base, sending RTCM on UART2 to the rover GPS. RTK is still possible with this setup.</long_desc>
<min>0</min>
<max>1</max>
<reboot_required>true</reboot_required>
<values>
<value code="0">Default</value>
<value code="1">Heading</value>
</values>
</parameter>
<parameter name="GPS_YAW_OFFSET" default="0." type="FLOAT"> <parameter name="GPS_YAW_OFFSET" default="0." type="FLOAT">
<short_desc>Heading/Yaw offset for dual antenna GPS</short_desc> <short_desc>Heading/Yaw offset for dual antenna GPS</short_desc>
<long_desc>Heading offset angle for dual antenna GPS setups that support heading estimation. (currently only for the Trimble MB-Two). Set this to 0 if the antennas are parallel to the forward-facing direction of the vehicle and the first antenna is in front. The offset angle increases counterclockwise. Set this to 90 if the first antenna is placed on the right side and the second on the left side of the vehicle.</long_desc> <long_desc>Heading offset angle for dual antenna GPS setups that support heading estimation. (currently only for the Trimble MB-Two). Set this to 0 if the antennas are parallel to the forward-facing direction of the vehicle and the first antenna is in front. The offset angle increases counterclockwise. Set this to 90 if the first antenna is placed on the right side and the second on the left side of the vehicle.</long_desc>
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment