Commit 3b7567eb authored by pixhawk's avatar pixhawk

bravo parameters added

parent ced2da0d
# Onboard parameters for system MAV 042
#
# MAV ID COMPONENT ID PARAM NAME VALUE (FLOAT)
42 200 ACC_NAV_OFFS_X 0
42 200 ACC_NAV_OFFS_Y 0
42 200 ACC_NAV_OFFS_Z -1000
42 200 ACC_OFFSET_X 0
42 200 ACC_OFFSET_Y 0
42 200 ACC_OFFSET_Z 0
42 200 ATT_KAL_IYAW 1
42 200 ATT_KAL_KACC 0.0033
42 200 ATT_OFFSET_X 0
42 200 ATT_OFFSET_Y 0
42 200 ATT_OFFSET_Z -0.08
42 200 CAM_EXP 1000
42 200 CAM_INTERVAL 36000
42 200 DEBUG_1 0
42 200 DEBUG_2 0
42 200 DEBUG_3 0
42 200 DEBUG_4 0
42 200 DEBUG_5 0
42 200 DEBUG_6 0
42 200 GYRO_OFFSET_X 29936
42 200 GYRO_OFFSET_Y 30294
42 200 GYRO_OFFSET_Z 29453
42 200 MIX_OFFSET 0
42 200 MIX_POSITION 0
42 200 MIX_POS_YAW 0
42 200 PID_ATT_AWU 0.3
42 200 PID_ATT_D 30
42 200 PID_ATT_I 60
42 200 PID_POS_AWU 5
42 200 PID_POS_D 2
42 200 PID_POS_I 0.4
42 200 PID_POS_P 1.8
42 200 PID_POS_Z_AWU 3
42 200 PID_POS_Z_D 0.2
42 200 PID_POS_Z_I 0.4
42 200 PID_POS_Z_LIM 0.3
42 200 PID_POS_Z_P 0.5
42 200 PID_YAWPOS_AWU 1
42 200 PID_YAWPOS_D 1
42 200 PID_YAWPOS_I 0.1
42 200 PID_YAWPOS_P 5
42 200 PID_YAWSPEED_D 0
42 200 PID_YAWSPEED_I 10
42 200 PID_YAWSPEED_P 30
42 200 PID_YAWSPE_AWU 1
42 200 POS_SP_ACCEPT 0
42 200 POS_SP_X 1.1
42 200 POS_SP_Y 1.1
42 200 POS_SP_YAW 0
42 200 POS_SP_Z -0.8
42 200 POS_TIMEOUT 2e+06
42 200 RC_NICK_CHAN 1
42 200 RC_ROLL_CHAN 2
42 200 RC_SAFETY_CHAN 5
42 200 RC_THRUST_CHAN 3
42 200 RC_TUNE_CHAN1 7
42 200 RC_TUNE_CHAN2 5
42 200 RC_TUNE_CHAN3 6
42 200 RC_TUNE_CHAN4 8
42 200 RC_YAW_CHAN 4
42 200 SEND_DEBUGCHAN 0
42 200 SLOT_ATTITUDE 1
42 200 SLOT_CONTROL 0
42 200 SLOT_RAW_IMU 0
42 200 SLOT_RC 0
42 200 SYS_COMP_ID 200
42 200 SYS_ID 42
42 200 SYS_IMU_RESET 0
42 200 SYS_SW_VER 2000
42 200 SYS_TYPE 2
42 200 UART_0_BAUD 115200
42 200 UART_1_BAUD 57600
42 200 VEL_DAMP 0.95
42 200 VEL_OFFSET_X 0
42 200 VEL_OFFSET_Y 0
42 200 VEL_OFFSET_Z 0
42 200 VIS_OUTL_TRESH 0.2
42 200 VIS_YAWCORR 0
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment