From 291e05849a8498ae3168c4cd972c9b89dd0007c0 Mon Sep 17 00:00:00 2001
From: PX4BuildBot <bot@px4.io>
Date: Tue, 12 Mar 2019 16:11:18 +0000
Subject: [PATCH] Update PX4 Firmware metadata Tue Mar 12 16:11:18 UTC 2019

---
 .../PX4/PX4ParameterFactMetaData.xml          | 19 +++++--------------
 1 file changed, 5 insertions(+), 14 deletions(-)

diff --git a/src/FirmwarePlugin/PX4/PX4ParameterFactMetaData.xml b/src/FirmwarePlugin/PX4/PX4ParameterFactMetaData.xml
index 4d92b3e8e..ca5389504 100644
--- a/src/FirmwarePlugin/PX4/PX4ParameterFactMetaData.xml
+++ b/src/FirmwarePlugin/PX4/PX4ParameterFactMetaData.xml
@@ -647,15 +647,6 @@ Note: ekf2 will limit the delta velocity bias estimate magnitude to be less than
       <decimal>1</decimal>
       <increment>0.5</increment>
     </parameter>
-    <parameter default="0" name="COM_DL_REG_T" type="INT32">
-      <short_desc>Datalink regain time threshold</short_desc>
-      <long_desc>After a data link loss: after this this amount of seconds with a healthy datalink the 'datalink loss' flag is set back to false</long_desc>
-      <min>0</min>
-      <max>3</max>
-      <unit>s</unit>
-      <decimal>1</decimal>
-      <increment>0.5</increment>
-    </parameter>
     <parameter default="5.0" name="COM_EF_C2T" type="FLOAT">
       <short_desc>Engine Failure Current/Throttle Threshold</short_desc>
       <long_desc>Engine failure triggers only below this current value</long_desc>
@@ -3825,6 +3816,11 @@ Used to calculate increased terrain random walk nosie due to movement</short_des
         <value code="5">Hold mode</value>
       </values>
     </parameter>
+    <parameter default="0" name="COM_OBS_AVOID" type="INT32">
+      <short_desc>Flag to enable obstacle avoidance
+Temporary Parameter to enable interface testing</short_desc>
+      <boolean />
+    </parameter>
     <parameter default="0" name="COM_POSCTL_NAVL" type="INT32">
       <short_desc>Position control navigation loss response</short_desc>
       <long_desc>This sets the flight mode that will be used if navigation accuracy is no longer adequate for position control. Navigation accuracy checks can be disabled using the CBRK_VELPOSERR parameter, but doing so will remove protection for all flight modes.</long_desc>
@@ -4627,11 +4623,6 @@ is 90 degrees. It should be lower than MPC_XY_CRUISE</short_desc>
       <unit>deg/s</unit>
       <decimal>1</decimal>
     </parameter>
-    <parameter default="0" name="MPC_OBS_AVOID" type="INT32">
-      <short_desc>Flag to enable obstacle avoidance
-Temporary Parameter to enable interface testing</short_desc>
-      <boolean />
-    </parameter>
     <parameter default="1" name="MPC_POS_MODE" type="INT32">
       <short_desc>Manual-Position control sub-mode</short_desc>
       <long_desc>The supported sub-modes are: 0 Default position control where sticks map to position/velocity directly. Maximum speeds is MPC_VEL_MANUAL. 1 Smooth position control where setpoints are adjusted based on acceleration limits and jerk limits. 2 Sport mode that is the same Default position control but with velocity limits set to the maximum allowed speeds (MPC_XY_VEL_MAX) 3 Smooth position control with maximum acceleration and jerk limits (different algorithm than 1).</long_desc>
-- 
2.22.0